Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1304912 > unrolled thread

[PATCH 0/9 REPOST] Tegra CLK Fixes

Back to article view | Back to linux.kernel

Contents

  [PATCH 0/9 REPOST] Tegra CLK Fixes Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    [PATCH 4/9] clk: tegra: Fix the misnaming of nvenc from msenc Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    [PATCH 3/9] clk: tegra210: Fix naming of MISC registers Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    [PATCH 2/9] clk: tegra210: Remove improper flags for lock_enable Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    [PATCH 6/9] clk: tegra210: fix pllx dyn step calculation Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    [PATCH 7/9] clk: tegra: pll: Do not disable PLLE when under HW control Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
      Re: [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate Thierry Reding <thierry.reding@gmail.com> - 2016-01-13 15:10 +0100
        Re: [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate Rhyland Klein <rklein@nvidia.com> - 2016-01-13 17:30 +0100
          Re: [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate Thierry Reding <thierry.reding@gmail.com> - 2016-01-13 18:30 +0100
    [PATCH 1/9] clk: tegra: Fix divider on VI_I2C Rhyland Klein <rklein@nvidia.com> - 2016-01-08 19:50 +0100
    Re: [PATCH 0/9 REPOST] Tegra CLK Fixes Thierry Reding <thierry.reding@gmail.com> - 2016-01-13 15:10 +0100

#1304912 — [PATCH 0/9 REPOST] Tegra CLK Fixes

This patch set fixes some issues found with the Tegra CLK drivers
in testing. There are also a few patches which clean up the code
and fix some naming issues.

Resending with correct email address for Mike Turquette.

Andrew Bresticker (1):
  clk: tegra: pll: Fix potential sleeping-while-atomic

Mark Kuo (2):
  clk: tegra: pll: Do not disable PLLE when under HW control
  clk: tegra: pll: Fix PLLE SS config

Rhyland Klein (6):
  clk: tegra: Fix divider on VI_I2C
  clk: tegra210: Remove improper flags for lock_enable
  clk: tegra210: Fix naming of MISC registers
  clk: tegra: Fix the misnaming of nvenc from msenc
  clk: tegra210: fix pllx dyn step calculation
  clk: tegra210: Initialize PLL_D2 to a sane rate

 drivers/clk/tegra/clk-pll.c          | 50 +++++++++++++--------
 drivers/clk/tegra/clk-tegra-periph.c |  4 +-
 drivers/clk/tegra/clk-tegra210.c     | 87 +++++++++++++++---------------------
 3 files changed, 71 insertions(+), 70 deletions(-)

-- 
1.9.1

[toc] | [next] | [standalone]

#1304913 — [PATCH 4/9] clk: tegra: Fix the misnaming of nvenc from msenc

When adding the nvenc clock, it was partially named msenc in
the code. Since the msenc clk isn't present in T210 where the nvenc
clk is, its misleading to see it present. Therefore, properly
rename it.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-tegra-periph.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/tegra/clk-tegra-periph.c b/drivers/clk/tegra/clk-tegra-periph.c
index 105405ca85ab..1860df1862dd 100644
--- a/drivers/clk/tegra/clk-tegra-periph.c
+++ b/drivers/clk/tegra/clk-tegra-periph.c
@@ -773,7 +773,7 @@ static struct tegra_periph_init_data periph_clks[] = {
 	XUSB("xusb_dev_src", mux_clkm_pllp_pllc_pllre, CLK_SOURCE_XUSB_DEV_SRC, 95, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_xusb_dev_src),
 	XUSB("xusb_dev_src", mux_clkm_pllp_pllre, CLK_SOURCE_XUSB_DEV_SRC, 95, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_xusb_dev_src_8),
 	MUX8("dbgapb", mux_pllp_clkm_2, CLK_SOURCE_DBGAPB, 185, TEGRA_PERIPH_NO_RESET, tegra_clk_dbgapb),
-	MUX8("msenc", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVENC, 219, 0, tegra_clk_nvenc),
+	MUX8("nvenc", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVENC, 219, 0, tegra_clk_nvenc),
 	MUX8("nvdec", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVDEC, 194, 0, tegra_clk_nvdec),
 	MUX8("nvjpg", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVJPG, 195, 0, tegra_clk_nvjpg),
 	MUX8("ape", mux_plla_pllc4_out0_pllc_pllc4_out1_pllp_pllc4_out2_clkm, CLK_SOURCE_APE, 198, TEGRA_PERIPH_ON_APB, tegra_clk_ape),
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1304914 — [PATCH 3/9] clk: tegra210: Fix naming of MISC registers

Some register for PLLM and PLLMB were named MISC0 but according to the
TRM, they have different names. Sync up the names to make it easier to
understand which register they are really referring to.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-tegra210.c | 36 ++++++++++++++++++------------------
 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index f45c9adf7fb2..2a7faa357130 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -59,7 +59,7 @@
 #define PLLC3_MISC3 0x50c
 
 #define PLLM_BASE 0x90
-#define PLLM_MISC0 0x9c
+#define PLLM_MISC2 0x9c
 #define PLLM_MISC1 0x98
 #define PLLP_BASE 0xa0
 #define PLLP_MISC0 0xac
@@ -99,7 +99,7 @@
 #define PLLC4_MISC0 0x5a8
 #define PLLC4_OUT 0x5e4
 #define PLLMB_BASE 0x5e8
-#define PLLMB_MISC0 0x5ec
+#define PLLMB_MISC1 0x5ec
 #define PLLA1_BASE 0x6a4
 #define PLLA1_MISC0 0x6a8
 #define PLLA1_MISC1 0x6ac
@@ -367,12 +367,12 @@ static const char *mux_pllmcp_clkm[] = {
 /* PLLMB */
 #define PLLMB_BASE_LOCK			(1 << 27)
 
-#define PLLMB_MISC0_LOCK_OVERRIDE	(1 << 18)
-#define PLLMB_MISC0_IDDQ		(1 << 17)
-#define PLLMB_MISC0_LOCK_ENABLE		(1 << 16)
+#define PLLMB_MISC1_LOCK_OVERRIDE	(1 << 18)
+#define PLLMB_MISC1_IDDQ		(1 << 17)
+#define PLLMB_MISC1_LOCK_ENABLE		(1 << 16)
 
-#define PLLMB_MISC0_DEFAULT_VALUE	0x00030000
-#define PLLMB_MISC0_WRITE_MASK		0x0007ffff
+#define PLLMB_MISC1_DEFAULT_VALUE	0x00030000
+#define PLLMB_MISC1_WRITE_MASK		0x0007ffff
 
 /* PLLP */
 #define PLLP_BASE_OVERRIDE		(1 << 28)
@@ -914,15 +914,15 @@ void tegra210_pllmb_set_defaults(struct tegra_clk_pll *pllmb)
 		 * PLL is ON: check if defaults already set, then set those
 		 * that can be updated in flight.
 		 */
-		val = PLLMB_MISC0_DEFAULT_VALUE & (~PLLMB_MISC0_IDDQ);
-		mask = PLLMB_MISC0_LOCK_ENABLE | PLLMB_MISC0_LOCK_OVERRIDE;
+		val = PLLMB_MISC1_DEFAULT_VALUE & (~PLLMB_MISC1_IDDQ);
+		mask = PLLMB_MISC1_LOCK_ENABLE | PLLMB_MISC1_LOCK_OVERRIDE;
 		_pll_misc_chk_default(clk_base, pllmb->params, 0, val,
-				~mask & PLLMB_MISC0_WRITE_MASK);
+				~mask & PLLMB_MISC1_WRITE_MASK);
 
 		/* Enable lock detect */
 		val = readl_relaxed(clk_base + pllmb->params->ext_misc_reg[0]);
 		val &= ~mask;
-		val |= PLLMB_MISC0_DEFAULT_VALUE & mask;
+		val |= PLLMB_MISC1_DEFAULT_VALUE & mask;
 		writel_relaxed(val, clk_base + pllmb->params->ext_misc_reg[0]);
 		udelay(1);
 
@@ -930,7 +930,7 @@ void tegra210_pllmb_set_defaults(struct tegra_clk_pll *pllmb)
 	}
 
 	/* set IDDQ, enable lock detect */
-	writel_relaxed(PLLMB_MISC0_DEFAULT_VALUE,
+	writel_relaxed(PLLMB_MISC1_DEFAULT_VALUE,
 			clk_base + pllmb->params->ext_misc_reg[0]);
 	udelay(1);
 }
@@ -1557,14 +1557,14 @@ static struct tegra_clk_pll_params pll_m_params = {
 	.vco_min = 800000000,
 	.vco_max = 1866000000,
 	.base_reg = PLLM_BASE,
-	.misc_reg = PLLM_MISC0,
+	.misc_reg = PLLM_MISC2,
 	.lock_mask = PLL_BASE_LOCK,
 	.lock_enable_bit_idx = PLLM_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
-	.iddq_reg = PLLM_MISC0,
+	.iddq_reg = PLLM_MISC2,
 	.iddq_bit_idx = PLLM_IDDQ_BIT,
 	.max_p = PLL_QLIN_PDIV_MAX,
-	.ext_misc_reg[0] = PLLM_MISC0,
+	.ext_misc_reg[0] = PLLM_MISC2,
 	.ext_misc_reg[0] = PLLM_MISC1,
 	.round_p_to_pdiv = pll_qlin_p_to_pdiv,
 	.pdiv_tohw = pll_qlin_pdiv_to_hw,
@@ -1584,13 +1584,13 @@ static struct tegra_clk_pll_params pll_mb_params = {
 	.vco_min = 800000000,
 	.vco_max = 1866000000,
 	.base_reg = PLLMB_BASE,
-	.misc_reg = PLLMB_MISC0,
+	.misc_reg = PLLMB_MISC1,
 	.lock_mask = PLL_BASE_LOCK,
 	.lock_delay = 300,
-	.iddq_reg = PLLMB_MISC0,
+	.iddq_reg = PLLMB_MISC1,
 	.iddq_bit_idx = PLLMB_IDDQ_BIT,
 	.max_p = PLL_QLIN_PDIV_MAX,
-	.ext_misc_reg[0] = PLLMB_MISC0,
+	.ext_misc_reg[0] = PLLMB_MISC1,
 	.round_p_to_pdiv = pll_qlin_p_to_pdiv,
 	.pdiv_tohw = pll_qlin_pdiv_to_hw,
 	.div_nmp = &pllm_nmp,
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1304915 — [PATCH 2/9] clk: tegra210: Remove improper flags for lock_enable

Most PLL's don't actually have LOCK_ENABLE bits. However, most PLL's
also had that flag set, which meant that the clk code was trying to
enable locks, and inadvertantly flipping bits in other fields.

For PLLM, ensure the correct register is used for the misc_register.
PLL_MISC0 contains the EN_LCKDET bit which should be used for enabling
the lock, and PLLM_MISC1 shouldn't be used at all.

Lastly, remove some of the settings which would point to the EN_LCKDET
bits for some PLLs. There is no need to enable the locks, and that is
done as part of the set_defaults logic already.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-tegra210.c | 42 ++++++++++++++--------------------------
 1 file changed, 14 insertions(+), 28 deletions(-)

diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index 58514c44ea83..f45c9adf7fb2 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -1386,7 +1386,7 @@ static struct tegra_clk_pll_params pll_c_params = {
 	.mdiv_default = 3,
 	.div_nmp = &pllc_nmp,
 	.freq_table = pll_cx_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.set_defaults = _pllc_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1425,7 +1425,7 @@ static struct tegra_clk_pll_params pll_c2_params = {
 	.ext_misc_reg[2] = PLLC2_MISC2,
 	.ext_misc_reg[3] = PLLC2_MISC3,
 	.freq_table = pll_cx_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.set_defaults = _pllc2_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1455,7 +1455,7 @@ static struct tegra_clk_pll_params pll_c3_params = {
 	.ext_misc_reg[2] = PLLC3_MISC2,
 	.ext_misc_reg[3] = PLLC3_MISC3,
 	.freq_table = pll_cx_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.set_defaults = _pllc3_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1505,7 +1505,6 @@ static struct tegra_clk_pll_params pll_c4_vco_params = {
 	.base_reg = PLLC4_BASE,
 	.misc_reg = PLLC4_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLSS_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.max_p = PLL_QLIN_PDIV_MAX,
 	.ext_misc_reg[0] = PLLC4_MISC0,
@@ -1517,8 +1516,7 @@ static struct tegra_clk_pll_params pll_c4_vco_params = {
 	.div_nmp = &pllss_nmp,
 	.freq_table = pll_c4_vco_freq_table,
 	.set_defaults = tegra210_pllc4_set_defaults,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE |
-		 TEGRA_PLL_VCO_OUT,
+	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_VCO_OUT,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
 
@@ -1559,7 +1557,7 @@ static struct tegra_clk_pll_params pll_m_params = {
 	.vco_min = 800000000,
 	.vco_max = 1866000000,
 	.base_reg = PLLM_BASE,
-	.misc_reg = PLLM_MISC1,
+	.misc_reg = PLLM_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
 	.lock_enable_bit_idx = PLLM_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
@@ -1588,7 +1586,6 @@ static struct tegra_clk_pll_params pll_mb_params = {
 	.base_reg = PLLMB_BASE,
 	.misc_reg = PLLMB_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLMB_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.iddq_reg = PLLMB_MISC0,
 	.iddq_bit_idx = PLLMB_IDDQ_BIT,
@@ -1598,7 +1595,7 @@ static struct tegra_clk_pll_params pll_mb_params = {
 	.pdiv_tohw = pll_qlin_pdiv_to_hw,
 	.div_nmp = &pllm_nmp,
 	.freq_table = pll_m_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.set_defaults = tegra210_pllmb_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1671,7 +1668,6 @@ static struct tegra_clk_pll_params pll_re_vco_params = {
 	.base_reg = PLLRE_BASE,
 	.misc_reg = PLLRE_MISC0,
 	.lock_mask = PLLRE_MISC_LOCK,
-	.lock_enable_bit_idx = PLLRE_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.max_p = PLL_QLIN_PDIV_MAX,
 	.ext_misc_reg[0] = PLLRE_MISC0,
@@ -1681,8 +1677,7 @@ static struct tegra_clk_pll_params pll_re_vco_params = {
 	.pdiv_tohw = pll_qlin_pdiv_to_hw,
 	.div_nmp = &pllre_nmp,
 	.freq_table = pll_re_vco_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_LOCK_MISC |
-		 TEGRA_PLL_HAS_LOCK_ENABLE | TEGRA_PLL_VCO_OUT,
+	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_LOCK_MISC | TEGRA_PLL_VCO_OUT,
 	.set_defaults = tegra210_pllre_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1712,7 +1707,6 @@ static struct tegra_clk_pll_params pll_p_params = {
 	.base_reg = PLLP_BASE,
 	.misc_reg = PLLP_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLP_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.iddq_reg = PLLP_MISC0,
 	.iddq_bit_idx = PLLXP_IDDQ_BIT,
@@ -1721,8 +1715,7 @@ static struct tegra_clk_pll_params pll_p_params = {
 	.div_nmp = &pllp_nmp,
 	.freq_table = pll_p_freq_table,
 	.fixed_rate = 408000000,
-	.flags = TEGRA_PLL_FIXED | TEGRA_PLL_USE_LOCK |
-		 TEGRA_PLL_HAS_LOCK_ENABLE | TEGRA_PLL_VCO_OUT,
+	.flags = TEGRA_PLL_FIXED | TEGRA_PLL_USE_LOCK | TEGRA_PLL_VCO_OUT,
 	.set_defaults = tegra210_pllp_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1750,7 +1743,7 @@ static struct tegra_clk_pll_params pll_a1_params = {
 	.ext_misc_reg[2] = PLLA1_MISC2,
 	.ext_misc_reg[3] = PLLA1_MISC3,
 	.freq_table = pll_cx_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.set_defaults = _plla1_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
@@ -1787,7 +1780,6 @@ static struct tegra_clk_pll_params pll_a_params = {
 	.base_reg = PLLA_BASE,
 	.misc_reg = PLLA_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLA_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.round_p_to_pdiv = pll_qlin_p_to_pdiv,
 	.pdiv_tohw = pll_qlin_pdiv_to_hw,
@@ -1802,8 +1794,7 @@ static struct tegra_clk_pll_params pll_a_params = {
 	.ext_misc_reg[1] = PLLA_MISC1,
 	.ext_misc_reg[2] = PLLA_MISC2,
 	.freq_table = pll_a_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_MDIV_NEW |
-		 TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK | TEGRA_MDIV_NEW,
 	.set_defaults = tegra210_plla_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 	.set_gain = tegra210_clk_pll_set_gain,
@@ -1836,7 +1827,6 @@ static struct tegra_clk_pll_params pll_d_params = {
 	.base_reg = PLLD_BASE,
 	.misc_reg = PLLD_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLD_MISC_LOCK_ENABLE,
 	.lock_delay = 1000,
 	.iddq_reg = PLLD_MISC0,
 	.iddq_bit_idx = PLLD_IDDQ_BIT,
@@ -1850,7 +1840,7 @@ static struct tegra_clk_pll_params pll_d_params = {
 	.ext_misc_reg[0] = PLLD_MISC0,
 	.ext_misc_reg[1] = PLLD_MISC1,
 	.freq_table = pll_d_freq_table,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.mdiv_default = 1,
 	.set_defaults = tegra210_plld_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
@@ -1876,7 +1866,6 @@ static struct tegra_clk_pll_params pll_d2_params = {
 	.base_reg = PLLD2_BASE,
 	.misc_reg = PLLD2_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLSS_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.iddq_reg = PLLD2_BASE,
 	.iddq_bit_idx = PLLSS_IDDQ_BIT,
@@ -1897,7 +1886,7 @@ static struct tegra_clk_pll_params pll_d2_params = {
 	.mdiv_default = 1,
 	.freq_table = tegra210_pll_d2_freq_table,
 	.set_defaults = tegra210_plld2_set_defaults,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 	.set_gain = tegra210_clk_pll_set_gain,
 	.adjust_vco = tegra210_clk_adjust_vco_min,
@@ -1920,7 +1909,6 @@ static struct tegra_clk_pll_params pll_dp_params = {
 	.base_reg = PLLDP_BASE,
 	.misc_reg = PLLDP_MISC,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLSS_MISC_LOCK_ENABLE,
 	.lock_delay = 300,
 	.iddq_reg = PLLDP_BASE,
 	.iddq_bit_idx = PLLSS_IDDQ_BIT,
@@ -1941,7 +1929,7 @@ static struct tegra_clk_pll_params pll_dp_params = {
 	.mdiv_default = 1,
 	.freq_table = pll_dp_freq_table,
 	.set_defaults = tegra210_plldp_set_defaults,
-	.flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+	.flags = TEGRA_PLL_USE_LOCK,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 	.set_gain = tegra210_clk_pll_set_gain,
 	.adjust_vco = tegra210_clk_adjust_vco_min,
@@ -1973,7 +1961,6 @@ static struct tegra_clk_pll_params pll_u_vco_params = {
 	.base_reg = PLLU_BASE,
 	.misc_reg = PLLU_MISC0,
 	.lock_mask = PLL_BASE_LOCK,
-	.lock_enable_bit_idx = PLLU_MISC_LOCK_ENABLE,
 	.lock_delay = 1000,
 	.iddq_reg = PLLU_MISC0,
 	.iddq_bit_idx = PLLU_IDDQ_BIT,
@@ -1983,8 +1970,7 @@ static struct tegra_clk_pll_params pll_u_vco_params = {
 	.pdiv_tohw = pll_qlin_pdiv_to_hw,
 	.div_nmp = &pllu_nmp,
 	.freq_table = pll_u_freq_table,
-	.flags = TEGRA_PLLU | TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE |
-		 TEGRA_PLL_VCO_OUT,
+	.flags = TEGRA_PLLU | TEGRA_PLL_USE_LOCK | TEGRA_PLL_VCO_OUT,
 	.set_defaults = tegra210_pllu_set_defaults,
 	.calc_rate = tegra210_pll_fixed_mdiv_cfg,
 };
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1304916 — [PATCH 6/9] clk: tegra210: fix pllx dyn step calculation

The logic for calculating the input rate used when figuring out
the proper dynamic steps for pllx was incorrect. It is supposed to
be calculated using parent_rate / m but it was just using the parent
rate directly, therefore using the wrong step values.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-tegra210.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index 2a7faa357130..5d8fac7052f2 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -780,13 +780,13 @@ static void pllx_get_dyn_steps(struct clk_hw *hw, u32 *step_a, u32 *step_b)
 {
 	unsigned long input_rate;
 
-	if (!IS_ERR_OR_NULL(hw->clk)) {
+	/* cf rate */
+	if (!IS_ERR_OR_NULL(hw->clk))
 		input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
-		/* cf rate */
-		input_rate /= tegra_pll_get_fixed_mdiv(hw, input_rate);
-	} else {
+	else
 		input_rate = 38400000;
-	}
+
+	input_rate /= tegra_pll_get_fixed_mdiv(hw, input_rate);
 
 	switch (input_rate) {
 	case 12000000:
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1304917 — [PATCH 7/9] clk: tegra: pll: Do not disable PLLE when under HW control

From: Mark Kuo <mkuo@nvidia.com>

SW should not disable PLLE if PLLE is already put under HW control.

Signed-off-by: Mark Kuo <mkuo@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-pll.c | 22 +++++++++++++++-------
 1 file changed, 15 insertions(+), 7 deletions(-)

diff --git a/drivers/clk/tegra/clk-pll.c b/drivers/clk/tegra/clk-pll.c
index 65156486889a..d9c3109b75bd 100644
--- a/drivers/clk/tegra/clk-pll.c
+++ b/drivers/clk/tegra/clk-pll.c
@@ -2012,7 +2012,7 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
 	struct tegra_clk_pll *pll = to_clk_pll(hw);
 	struct tegra_clk_pll_freq_table sel;
 	u32 val;
-	int ret;
+	int ret = 0;
 	unsigned long flags = 0;
 	unsigned long input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
 
@@ -2022,16 +2022,14 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
 	if (pll->lock)
 		spin_lock_irqsave(pll->lock, flags);
 
+	val = pll_readl(pll->params->aux_reg, pll);
+	if (val & PLLE_AUX_SEQ_ENABLE)
+		goto out;
+
 	val = pll_readl_base(pll);
 	val &= ~BIT(30); /* Disable lock override */
 	pll_writel_base(val, pll);
 
-	val = pll_readl(pll->params->aux_reg, pll);
-	val |= PLLE_AUX_ENABLE_SWCTL;
-	val &= ~PLLE_AUX_SEQ_ENABLE;
-	pll_writel(val, pll->params->aux_reg, pll);
-	udelay(1);
-
 	val = pll_readl_misc(pll);
 	val |= PLLE_MISC_LOCK_ENABLE;
 	val |= PLLE_MISC_IDDQ_SW_CTRL;
@@ -2104,15 +2102,25 @@ static void clk_plle_tegra210_disable(struct clk_hw *hw)
 	if (pll->lock)
 		spin_lock_irqsave(pll->lock, flags);
 
+	/* If PLLE HW sequencer is enabled, SW should not disable PLLE */
+	val = pll_readl(pll->params->aux_reg, pll);
+	if (val & PLLE_AUX_SEQ_ENABLE)
+		goto out;
+
 	val = pll_readl_base(pll);
 	val &= ~PLLE_BASE_ENABLE;
 	pll_writel_base(val, pll);
 
+	val = pll_readl(pll->params->aux_reg, pll);
+	val |= PLLE_AUX_ENABLE_SWCTL | PLLE_AUX_SS_SWCTL;
+	pll_writel(val, pll->params->aux_reg, pll);
+
 	val = pll_readl_misc(pll);
 	val |= PLLE_MISC_IDDQ_SW_CTRL | PLLE_MISC_IDDQ_SW_VALUE;
 	pll_writel_misc(val, pll);
 	udelay(1);
 
+out:
 	if (pll->lock)
 		spin_unlock_irqrestore(pll->lock, flags);
 }
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1304918 — [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate

Initialize PLL_D2 to a sane rate at the start of the day.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-tegra210.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index 5d8fac7052f2..cc560a1f6efb 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -2749,6 +2749,7 @@ static struct tegra_clk_init_table init_table[] __initdata = {
 	{ TEGRA210_CLK_PLL_DP, TEGRA210_CLK_CLK_MAX, 270000000, 0 },
 	{ TEGRA210_CLK_SOC_THERM, TEGRA210_CLK_PLL_P, 51000000, 0 },
 	{ TEGRA210_CLK_CCLK_G, TEGRA210_CLK_CLK_MAX, 0, 1 },
+	{ TEGRA210_CLK_PLL_D2, TEGRA210_CLK_CLK_MAX, 594000000, 0 },
 	/* This MUST be the last entry. */
 	{ TEGRA210_CLK_CLK_MAX, TEGRA210_CLK_CLK_MAX, 0, 0 },
 };
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1308433 — Re: [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate

[Multipart message — attachments visible in raw view] — view raw

On Fri, Jan 08, 2016 at 01:45:14PM -0500, Rhyland Klein wrote:
> Initialize PLL_D2 to a sane rate at the start of the day.
> 
> Signed-off-by: Rhyland Klein <rklein@nvidia.com>
> ---
>  drivers/clk/tegra/clk-tegra210.c | 1 +
>  1 file changed, 1 insertion(+)

There are a lot of assumptions in this commit message. I'm asking myself
why does it need to be initialized to any rate at all? Isn't it up to
the user driver to set the PLL to whatever it knows to be a sane rate?
Why is 594 MHz a sane rate?

A good commit message should answer those questions.

Thierry

[toc] | [prev] | [next] | [standalone]

#1308567 — Re: [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate

On 1/13/2016 9:03 AM, Thierry Reding wrote:
> * PGP Signed by an unknown key
> 
> On Fri, Jan 08, 2016 at 01:45:14PM -0500, Rhyland Klein wrote:
>> Initialize PLL_D2 to a sane rate at the start of the day.
>>
>> Signed-off-by: Rhyland Klein <rklein@nvidia.com>
>> ---
>>  drivers/clk/tegra/clk-tegra210.c | 1 +
>>  1 file changed, 1 insertion(+)
> 
> There are a lot of assumptions in this commit message. I'm asking myself
> why does it need to be initialized to any rate at all? Isn't it up to
> the user driver to set the PLL to whatever it knows to be a sane rate?
> Why is 594 MHz a sane rate?
> 
> A good commit message should answer those questions.
> 

Thanks. This patch came about in response to some work with
suspend/resume logic in the ChromeOS kernel. In the suspend/resume patch
there, it reads all clk rates and caches them in suspend, then re-sets
them on resume. We hadn't been using pll_d2 at all, and its rate (when
read in suspend()) came back as 0. Then in resume, we would tr to set
it, clk_set_rate(pll_d2, 0) and would generate a warning/error that 0
wasn't a valid rate.

As for the specific rate I chose, I simply took one off the table of
supported frequencies in the clk-tegra210 code, so that it was non-zero.

Since we don't support suspend/resume right now in the clk drivers, I
don't think its urgent to merge this patch. I can drop in in the next
rev if thats easier.

-rhyland


-- 
nvpublic

[toc] | [prev] | [next] | [standalone]

#1308653 — Re: [PATCH 9/9] clk: tegra210: Initialize PLL_D2 to a sane rate

[Multipart message — attachments visible in raw view] — view raw

On Wed, Jan 13, 2016 at 11:27:09AM -0500, Rhyland Klein wrote:
> On 1/13/2016 9:03 AM, Thierry Reding wrote:
> > * PGP Signed by an unknown key
> > 
> > On Fri, Jan 08, 2016 at 01:45:14PM -0500, Rhyland Klein wrote:
> >> Initialize PLL_D2 to a sane rate at the start of the day.
> >>
> >> Signed-off-by: Rhyland Klein <rklein@nvidia.com>
> >> ---
> >>  drivers/clk/tegra/clk-tegra210.c | 1 +
> >>  1 file changed, 1 insertion(+)
> > 
> > There are a lot of assumptions in this commit message. I'm asking myself
> > why does it need to be initialized to any rate at all? Isn't it up to
> > the user driver to set the PLL to whatever it knows to be a sane rate?
> > Why is 594 MHz a sane rate?
> > 
> > A good commit message should answer those questions.
> > 
> 
> Thanks. This patch came about in response to some work with
> suspend/resume logic in the ChromeOS kernel. In the suspend/resume patch
> there, it reads all clk rates and caches them in suspend, then re-sets
> them on resume. We hadn't been using pll_d2 at all, and its rate (when
> read in suspend()) came back as 0. Then in resume, we would tr to set
> it, clk_set_rate(pll_d2, 0) and would generate a warning/error that 0
> wasn't a valid rate.
> 
> As for the specific rate I chose, I simply took one off the table of
> supported frequencies in the clk-tegra210 code, so that it was non-zero.
> 
> Since we don't support suspend/resume right now in the clk drivers, I
> don't think its urgent to merge this patch. I can drop in in the next
> rev if thats easier.

Yes, that would be my preference as well. Once suspend/resume support
gets added we should run into this again. Setting the rate so some sane
value (the meaning of which is highly dependent on the use-case) sounds
to me more like a workaround rather than a real fix.

pll_d2 is used for display, so I don't quite understand why we'd have
to restore the rate on resume, since DRM/KMS would set it to whatever
it needs at a higher level anyway. Perhaps this will turn out to be a
non-issue upstream.

Thierry

[toc] | [prev] | [next] | [standalone]

#1304922 — [PATCH 1/9] clk: tegra: Fix divider on VI_I2C

VI-I2C has 16 bits available for its divider. Switch the divider
width to 16 instead of 8 so correct rates can be set.

Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
 drivers/clk/tegra/clk-tegra-periph.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/tegra/clk-tegra-periph.c b/drivers/clk/tegra/clk-tegra-periph.c
index 6ad381a888a6..105405ca85ab 100644
--- a/drivers/clk/tegra/clk-tegra-periph.c
+++ b/drivers/clk/tegra/clk-tegra-periph.c
@@ -782,7 +782,7 @@ static struct tegra_periph_init_data periph_clks[] = {
 	NODIV("sor1", mux_clkm_sor1_brick_sor1_src, CLK_SOURCE_SOR1, 15, MASK(1), 183, 0, tegra_clk_sor1, &sor1_lock),
 	MUX8("sdmmc_legacy", mux_pllp_out3_clkm_pllp_pllc4, CLK_SOURCE_SDMMC_LEGACY, 193, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_sdmmc_legacy),
 	MUX8("qspi", mux_pllp_pllc_pllc_out1_pllc4_out2_pllc4_out1_clkm_pllc4_out0, CLK_SOURCE_QSPI, 211, TEGRA_PERIPH_ON_APB, tegra_clk_qspi),
-	MUX("vii2c", mux_pllp_pllc_clkm, CLK_SOURCE_VI_I2C, 208, TEGRA_PERIPH_ON_APB, tegra_clk_vi_i2c),
+	I2C("vii2c", mux_pllp_pllc_clkm, CLK_SOURCE_VI_I2C, 208, tegra_clk_vi_i2c),
 	MUX("mipibif", mux_pllp_clkm, CLK_SOURCE_MIPIBIF, 173, TEGRA_PERIPH_ON_APB, tegra_clk_mipibif),
 	MUX("uartape", mux_pllp_pllc_clkm, CLK_SOURCE_UARTAPE, 212, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_uartape),
 	MUX8("tsecb", mux_pllp_pllc2_c_c3_clkm, CLK_SOURCE_TSECB, 206, 0, tegra_clk_tsecb),
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1308436

[Multipart message — attachments visible in raw view] — view raw

On Fri, Jan 08, 2016 at 01:45:05PM -0500, Rhyland Klein wrote:
> This patch set fixes some issues found with the Tegra CLK drivers
> in testing. There are also a few patches which clean up the code
> and fix some naming issues.
> 
> Resending with correct email address for Mike Turquette.
> 
> Andrew Bresticker (1):
>   clk: tegra: pll: Fix potential sleeping-while-atomic
> 
> Mark Kuo (2):
>   clk: tegra: pll: Do not disable PLLE when under HW control
>   clk: tegra: pll: Fix PLLE SS config
> 
> Rhyland Klein (6):
>   clk: tegra: Fix divider on VI_I2C
>   clk: tegra210: Remove improper flags for lock_enable
>   clk: tegra210: Fix naming of MISC registers
>   clk: tegra: Fix the misnaming of nvenc from msenc
>   clk: tegra210: fix pllx dyn step calculation
>   clk: tegra210: Initialize PLL_D2 to a sane rate
> 
>  drivers/clk/tegra/clk-pll.c          | 50 +++++++++++++--------
>  drivers/clk/tegra/clk-tegra-periph.c |  4 +-
>  drivers/clk/tegra/clk-tegra210.c     | 87 +++++++++++++++---------------------
>  3 files changed, 71 insertions(+), 70 deletions(-)

Rhyland,

This looks like a very nice round of fixups for the clock driver. I've
replied to a couple of individual patches where I thought things could
be improved a little, but they're mostly minor things.

Thierry

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web