Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1625429

Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for power-domains

Show all headers | View raw

On 17/04/17 06:27, Viresh Kumar wrote:
> On 13-04-17, 14:42, Sudeep Holla wrote:
>> What I was referring is about power domain provider with multiple power
>> domains(simply #power-domain-cells=<1> case as explained in the
>> power-domain specification.
> 
> I am not sure if we should be looking to target such a situation for now, as
> that would be like this:
> 
> Device controlled by Domain A. Domain A itself is controlled by Domain B and
> Domain C.
> 

No, may be I was not so clear. I am just referring a power controller
that provides say 3 different power domains and are indexed 0 - 2.
The consumer just passes the index along with the phandle for the power
domain info.

> Though we will end up converting the domain-performance-state property to an
> array if that is required in near future.
> 

OK, better to document that so that we know how to extend it. We have
#power-domain-cells=<1> on Juno with SCPI.

>> Yes. To simplify what not we just have power-domain for a device and
>> change state of that domain to change the performance of that device.
> 
> Consider this case to understand what I have in Mind.
> 
> The power domain have its states as A, B, C, D. There can be multiple devices
> regulated by that domain and one of the devices have its power states as: A1,
> A2, A3, B1, B2, B3, C1, C2, C3, D1, D2, D3 and all these states have different
> frequency/voltages.
> 
> IOW, the devices can have regulators as well and may want to fine tune within
> the domain performance-state.
> 

Understood. I would incline towards reusing regulators we that's what is
changed behind the scene. Calling this operating performance point
is misleading and doesn't align well with existing specs/features.

>> Then put this in the hierarchy. Some thing similar to what we already
>> have with new domain-idle states. In that way, we can move any
>> performance control to the domain and abstract the clocks and regulators
>> from the devices as the first step and from the OSPM view if there's
>> firmware support.
>>
>> If we are looking this power-domains with performance as just some
>> *advanced regulators*, I don't like the complexity added.
> 
> In the particular case I am trying to solve (Qcom), we have some sort of
> regulators which are only programmed by a M3 core. The M3 core needs integer
> numbers representing state we want the domain to be in and it will put the
> regulators (or whatever) in a particular state.
> 

Understood. We have exactly same thing with SCPI but it controls both
frequency and voltage referred as operating points. In general, this OPP
terminology is used in SCPI/ACPI/SCMI specifications as both frequency
and voltage control. I am bit worried that this binding might introduce
confusions on the definitions. But it can be reworded/renamed easily if
required.

-- 
Regards,
Sudeep

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Sudeep Holla <sudeep.holla@arm.com> - 2017-04-12 19:00 +0200
  Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-13 07:40 +0200
    Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Sudeep Holla <sudeep.holla@arm.com> - 2017-04-13 15:50 +0200
      Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-17 07:30 +0200
        Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Sudeep Holla <sudeep.holla@arm.com> - 2017-04-18 18:10 +0200
          Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-19 12:20 +0200
          Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-19 13:50 +0200
            Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Sudeep Holla <sudeep.holla@arm.com> - 2017-04-19 16:00 +0200
              Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-20 07:30 +0200
                Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for power-domains Ulf Hansson <ulf.hansson@linaro.org> - 2017-04-20 10:30 +0200
                Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-20 11:40 +0200
                Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Sudeep Holla <sudeep.holla@arm.com> - 2017-04-20 12:00 +0200
                Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Sudeep Holla <sudeep.holla@arm.com> - 2017-04-20 11:50 +0200
                Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for  power-domains Viresh Kumar <viresh.kumar@linaro.org> - 2017-04-20 12:00 +0200
                Re: [PATCH V4 1/9] PM / OPP: Allow OPP table to be used for power-domains Kevin Hilman <khilman@baylibre.com> - 2017-04-24 21:10 +0200

csiph-web