Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1400983

Re: [PATCH 2/4] phy: rockchip-emmc: configure frequency range and drive impedance

Show all headers | View raw

On Fri, May 13, 2016 at 11:46:33AM -0700, Doug Anderson wrote:
> On Thu, May 12, 2016 at 6:02 PM, Shawn Lin <shawn.lin@rock-chips.com> wrote:
> > On 2016/5/13 6:43, Brian Norris wrote:
> >> @@ -154,6 +167,20 @@ static int rockchip_emmc_phy_power_on(struct phy
> >> *phy)
> >>         struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
> >>         int ret = 0;
> >>
> >> +       /* DLL operation: 170 to 200 MHz */
> >
> >
> > What is 170 here? Should we expose them to dt instead of hardcoding
> > them?
> 
> This was probably my fault.  I did some searching and found
> <https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf>.
> It appears to be docs for a similar (but not identical) PHY.  We were
> looking at it to try to get more clarity on some bits that were hard
> to understand in the docs we had.
> 
> In that doc there appear to be 3 bits for selecting the DLL operation
> and they have ranges defined.  In Rockchip's PHY there are only 2
> bits.  Thus things don't map totally properly.
> 
> Anyway, comment should probably be removed.

[...]

> So overall:
> 
> * Should re-spin and remove the comment about 170 MHz.
> 
> * I think this could land as-is other than the comment.

Right, will fix the first bullet point.

Brian

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

[PATCH 1/4] phy: rockchip-emmc: give DLL some extra time to be ready Brian Norris <briannorris@chromium.org> - 2016-05-13 00:50 +0200
  [PATCH 3/4] phy: rockchip-emmc: configure default output tap delay Brian Norris <briannorris@chromium.org> - 2016-05-13 00:50 +0200
    Re: [PATCH 3/4] phy: rockchip-emmc: configure default output tap delay Doug Anderson <dianders@chromium.org> - 2016-05-14 00:30 +0200
      Re: [PATCH 3/4] phy: rockchip-emmc: configure default output tap  delay Shawn Lin <shawn.lin@rock-chips.com> - 2016-05-16 06:20 +0200
        Re: [PATCH 3/4] phy: rockchip-emmc: configure default output tap delay Doug Anderson <dianders@chromium.org> - 2016-05-16 17:20 +0200
  [PATCH 2/4] phy: rockchip-emmc: configure frequency range and drive impedance Brian Norris <briannorris@chromium.org> - 2016-05-13 00:50 +0200
    Re: [PATCH 2/4] phy: rockchip-emmc: configure frequency range and  drive impedance Shawn Lin <shawn.lin@rock-chips.com> - 2016-05-13 03:10 +0200
      Re: [PATCH 2/4] phy: rockchip-emmc: configure frequency range and  drive impedance Doug Anderson <dianders@chromium.org> - 2016-05-13 20:50 +0200
        Re: [PATCH 2/4] phy: rockchip-emmc: configure frequency range and  drive impedance Brian Norris <briannorris@chromium.org> - 2016-05-13 23:10 +0200
        Re: [PATCH 2/4] phy: rockchip-emmc: configure frequency range and  drive impedance Doug Anderson <dianders@chromium.org> - 2016-05-24 07:00 +0200
    [PATCH v2 2/4] phy: rockchip-emmc: configure frequency range and  drive impedance Brian Norris <briannorris@chromium.org> - 2016-05-13 23:10 +0200
      Re: [PATCH v2 2/4] phy: rockchip-emmc: configure frequency range and  drive impedance Doug Anderson <dianders@chromium.org> - 2016-05-14 00:10 +0200
  [PATCH 4/4] phy: rockchip-emmc: reindent the register definitions Brian Norris <briannorris@chromium.org> - 2016-05-13 00:50 +0200
    Re: [PATCH 4/4] phy: rockchip-emmc: reindent the register definitions Doug Anderson <dianders@chromium.org> - 2016-05-14 00:30 +0200
  Re: [PATCH 1/4] phy: rockchip-emmc: give DLL some extra time to be ready Doug Anderson <dianders@chromium.org> - 2016-05-14 00:10 +0200

csiph-web