Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]
Groups > linux.kernel > #1416646
| From | Jarod Wilson <jarod@redhat.com> |
|---|---|
| Newsgroups | linux.kernel |
| Subject | Re: [PATCH net v2] sfc: report supported link speeds on SFP connections |
| Date | 2016-06-07 23:30 +0200 |
| Message-ID | <rHwJs-7Uj-1@gated-at.bofh.it> (permalink) |
| References | <rFMfD-58M-5@gated-at.bofh.it> <rH5Jg-7nV-31@gated-at.bofh.it> <rH7UK-da-9@gated-at.bofh.it> |
| Organization | linux.* mail to news gateway |
On Mon, Jun 06, 2016 at 02:55:29PM -0400, Jarod Wilson wrote: > On Mon, Jun 06, 2016 at 05:29:30PM +0100, Bert Kenward wrote: > > 7000-series SFC NICs connected with an SFP+ module currently fail to > > report any supported link speeds. > > > > Reported-by: Jarod Wilson <jarod@redhat.com> > > Signed-off-by: Bert Kenward <bkenward@solarflare.com> > > Had a feeling my cut might not have been quite right. Looks good to me. > > Reviewed-by: Jarod Wilson <jarod@redhat.com> ...however, upon testing, there's a gotcha. This results in my 10Gbps sfc nic reporting that it supports 40Gbps: $ ethtool ens4f0 Settings for ens4f0: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full 40000baseKR4/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Link partner advertised link modes: 10000baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 255 Transceiver: internal Auto-negotiation: on Cannot get wake-on-lan settings: Operation not permitted Current message level: 0x000020f7 (8439) drv probe link ifdown ifup rx_err tx_err hw Link detected: yes $ ethtool -i ens4f0 driver: sfc version: 4.0 firmware-version: 4.6.1.1001 rx1 tx1 expansion-rom-version: bus-info: 0000:05:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: no $ lspci -v -s 0000:05:00.0 05:00.0 Ethernet controller: Solarflare Communications SFC9120 (rev 01) Subsystem: Solarflare Communications SFN7x22F-R2 Flareon Ultra 7000 Series 10G Adapter Physical Slot: 4 Flags: bus master, fast devsel, latency 0, IRQ 16 I/O ports at c100 [size=256] Memory at ef000000 (64-bit, non-prefetchable) [size=8M] Memory at ef884000 (64-bit, non-prefetchable) [size=16K] Expansion ROM at ef840000 [disabled] [size=256K] Capabilities: <access denied> Kernel driver in use: sfc One solution would be to move the case MC_CMD_MEDIA_QSFP_PLUS above XFP/SFP_PLUS, only check the 40Gbps cap, no break, fall through into the XFP/SFP_PLUS chunk, continue processing there. -- Jarod Wilson jarod@redhat.com
Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread
[PATCH net] ethernet/sfc: report supported link speeds on SFP connections Jarod Wilson <jarod@redhat.com> - 2016-06-03 03:40 +0200
Re: [PATCH net] ethernet/sfc: report supported link speeds on SFP connections David Miller <davem@davemloft.net> - 2016-06-04 02:00 +0200
Re: [PATCH net] ethernet/sfc: report supported link speeds on SFP connections Bert Kenward <bkenward@solarflare.com> - 2016-06-06 17:20 +0200
[PATCH net v2] sfc: report supported link speeds on SFP connections Bert Kenward <bkenward@solarflare.com> - 2016-06-06 18:40 +0200
Re: [PATCH net v2] sfc: report supported link speeds on SFP connections Jarod Wilson <jarod@redhat.com> - 2016-06-06 21:00 +0200
Re: [PATCH net v2] sfc: report supported link speeds on SFP connections Jarod Wilson <jarod@redhat.com> - 2016-06-07 23:30 +0200
Re: [PATCH net v2] sfc: report supported link speeds on SFP connections Jarod Wilson <jarod@redhat.com> - 2016-06-08 15:50 +0200
Re: [PATCH net v2] sfc: report supported link speeds on SFP connections David Miller <davem@davemloft.net> - 2016-06-08 20:20 +0200
csiph-web