Groups > linux.kernel > #1470377 > unrolled thread

[PATCH v3 0/5] net/usb: asix driver improvements

Started by	robert.foss@collabora.com
First post	2016-08-25 22:20 +0200
Last post	2016-09-01 06:10 +0200
Articles	20 on this page of 23 — 5 participants

Back to article view | Back to linux.kernel

  [PATCH v3 0/5] net/usb: asix driver improvements robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 3/5] net: asix: Fix AX88772x resume failures robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 1/5] net: asix: Add in_pm parameter robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 3/5] net: asix: Fix AX88772x resume failures robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg robert.foss@collabora.com - 2016-08-25 22:20 +0200
      Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg Robert Foss <robert.foss@collabora.com> - 2016-09-01 18:50 +0200
        Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg Eric Dumazet <eric.dumazet@gmail.com> - 2016-09-01 23:10 +0200
          Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg Grant Grundler <grundler@google.com> - 2016-09-06 18:50 +0200
            Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg Robert Foss <robert.foss@collabora.com> - 2016-09-06 23:50 +0200
      Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg Eric Dumazet <eric.dumazet@gmail.com> - 2016-09-01 18:50 +0200
    [PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected robert.foss@collabora.com - 2016-08-25 22:20 +0200
    [PATCH v3 1/5] net: asix: Add in_pm parameter robert.foss@collabora.com - 2016-08-25 22:20 +0200
    Re: [PATCH v3 0/5] net/usb: asix driver improvements David Miller <davem@davemloft.net> - 2016-08-27 06:30 +0200
    [PATCH v3 3/5] net: asix: Fix AX88772x resume failures robert.foss@collabora.com - 2016-08-29 15:40 +0200
    [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg robert.foss@collabora.com - 2016-08-29 15:40 +0200
    [PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected robert.foss@collabora.com - 2016-08-29 15:40 +0200
    [PATCH v3 1/5] net: asix: Add in_pm parameter robert.foss@collabora.com - 2016-08-29 15:40 +0200
    [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset robert.foss@collabora.com - 2016-08-29 15:40 +0200
    Re: [PATCH v3 0/5] net/usb: asix driver improvements Robert Foss <robert.foss@collabora.com> - 2016-08-31 19:30 +0200
    Re: [PATCH v3 0/5] net/usb: asix driver improvements David Miller <davem@davemloft.net> - 2016-09-01 06:10 +0200

Page 1 of 2 [1] 2 Next page →

#1470377 — [PATCH v3 0/5] net/usb: asix driver improvements

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 0/5] net/usb: asix driver improvements
Message-ID	<sa9i1-5Ly-3@gated-at.bofh.it>

From: Robert Foss <robert.foss@collabora.com>

This series improves power management of the asix driver.

 - Suspend/resume support is improved to save needed registers.
 - Device disconnection is improved.
 - Fixes AX88772x resume failures
 - Implementes IEEE 802.3 spec section "22.2.4.1.1 Reset" correctly
 - Fixes AX_CMD_WRITE_MEDIUM_MODE being set incorrectly

Changes since v1:
- Added proper metadata tags to series.
- Added two more patches to series.

Changes since v2:
- Added coverletter
- Tested patches on AX88772A/AX88772B/AX88178/AX88179 hardware

Allan Chou (1):
  net: asix: Fix AX88772x resume failures

Freddy Xin (1):
  net: asix: Add in_pm parameter

Grant Grundler (2):
  net: asix: see 802.3 spec for phy reset
  net: asix: autoneg will set WRITE_MEDIUM reg

Vincent Palatin (1):
  net: asix: Avoid looping when the device is disconnected

 drivers/net/usb/asix.h         |  40 ++-
 drivers/net/usb/asix_common.c  | 212 ++++++++++++----
 drivers/net/usb/asix_devices.c | 450 +++++++++++++++++++++++++++-------
 drivers/net/usb/ax88172a.c     |  29 +-
 4 files changed, 575 insertions(+), 156 deletions(-)

-- 
git-series 0.8.10

[toc] | [next] | [standalone]

#1470379 — [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 4/5] net: asix: see 802.3 spec for phy reset
Message-ID	<sa9i2-5Ly-7@gated-at.bofh.it>
In reply to	#1470377

From: Robert Foss <robert.foss@collabora.com>

From: Grant Grundler <grundler@chromium.org>

https://lkml.org/lkml/2014/11/11/947

Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.

Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 27 ++++++++++++++++++++++++---
 1 file changed, 24 insertions(+), 3 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index 083dc2e..dbcdda2 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -212,6 +212,28 @@ static const struct net_device_ops ax88172_netdev_ops = {
 	.ndo_set_rx_mode	= ax88172_set_multicast,
 };
 
+static void asix_phy_reset(struct usbnet *dev, unsigned int reset_bits)
+{
+	unsigned int timeout = 5000;
+
+	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, reset_bits);
+
+	/* give phy_id a chance to process reset */
+	udelay(500);
+
+	/* See IEEE 802.3 "22.2.4.1.1 Reset": 500ms max */
+	while (timeout--) {
+		if (asix_mdio_read(dev->net, dev->mii.phy_id, MII_BMCR)
+							& BMCR_RESET)
+			udelay(100);
+		else
+			return;
+	}
+
+	netdev_err(dev->net, "BMCR_RESET timeout on phy_id %d\n",
+		   dev->mii.phy_id);
+}
+
 static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	int ret = 0;
@@ -258,7 +280,7 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
+	asix_phy_reset(dev, BMCR_RESET);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
 		ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
 	mii_nway_restart(&dev->mii);
@@ -900,8 +922,7 @@ static int ax88178_reset(struct usbnet *dev)
 	} else if (data->phymode == PHY_MODE_RTL8211CL)
 		rtl8211cl_phy_init(dev);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR,
-			BMCR_RESET | BMCR_ANENABLE);
+	asix_phy_reset(dev, BMCR_RESET | BMCR_ANENABLE);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
 			ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000,
-- 
git-series 0.8.10

[toc] | [prev] | [next] | [standalone]

#1470380 — [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 4/5] net: asix: see 802.3 spec for phy reset
Message-ID	<sa9i2-5Ly-15@gated-at.bofh.it>
In reply to	#1470377

From: Grant Grundler <grundler@chromium.org>

        https://lkml.org/lkml/2014/11/11/947

Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.

Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 27 ++++++++++++++++++++++++---
 1 file changed, 24 insertions(+), 3 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index 083dc2e..dbcdda2 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -212,6 +212,28 @@ static const struct net_device_ops ax88172_netdev_ops = {
 	.ndo_set_rx_mode	= ax88172_set_multicast,
 };
 
+static void asix_phy_reset(struct usbnet *dev, unsigned int reset_bits)
+{
+	unsigned int timeout = 5000;
+
+	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, reset_bits);
+
+	/* give phy_id a chance to process reset */
+	udelay(500);
+
+	/* See IEEE 802.3 "22.2.4.1.1 Reset": 500ms max */
+	while (timeout--) {
+		if (asix_mdio_read(dev->net, dev->mii.phy_id, MII_BMCR)
+							& BMCR_RESET)
+			udelay(100);
+		else
+			return;
+	}
+
+	netdev_err(dev->net, "BMCR_RESET timeout on phy_id %d\n",
+		   dev->mii.phy_id);
+}
+
 static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	int ret = 0;
@@ -258,7 +280,7 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
+	asix_phy_reset(dev, BMCR_RESET);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
 		ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
 	mii_nway_restart(&dev->mii);
@@ -900,8 +922,7 @@ static int ax88178_reset(struct usbnet *dev)
 	} else if (data->phymode == PHY_MODE_RTL8211CL)
 		rtl8211cl_phy_init(dev);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR,
-			BMCR_RESET | BMCR_ANENABLE);
+	asix_phy_reset(dev, BMCR_RESET | BMCR_ANENABLE);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
 			ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000,
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1470382 — [PATCH v3 3/5] net: asix: Fix AX88772x resume failures

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 3/5] net: asix: Fix AX88772x resume failures
Message-ID	<sa9i2-5Ly-13@gated-at.bofh.it>
In reply to	#1470377

From: Allan Chou <allan@asix.com.tw>

The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY

Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 47 +++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 46 insertions(+), 1 deletion(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index ebeb730..083dc2e 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -35,6 +35,15 @@
 
 #define	PHY_MODE_RTL8211CL	0x000C
 
+#define AX88772A_PHY14H		0x14
+#define AX88772A_PHY14H_DEFAULT 0x442C
+
+#define AX88772A_PHY15H		0x15
+#define AX88772A_PHY15H_DEFAULT 0x03C8
+
+#define AX88772A_PHY16H		0x16
+#define AX88772A_PHY16H_DEFAULT 0x4044
+
 struct ax88172_int_data {
 	__le16 res1;
 	u8 link;
@@ -424,7 +433,7 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
-	u16 rx_ctl;
+	u16 rx_ctl, phy14h, phy15h, phy16h;
 	u8 chipcode = 0;
 
 	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
@@ -482,6 +491,32 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 				   ret);
 			goto out;
 		}
+	} else if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772A_CHIPCODE) {
+		/* Check if the PHY registers have default settings */
+		phy14h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H);
+		phy15h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H);
+		phy16h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H);
+
+		netdev_dbg(dev->net,
+			   "772a_hw_reset: MR20=0x%x MR21=0x%x MR22=0x%x\n",
+			   phy14h, phy15h, phy16h);
+
+		/* Restore PHY registers default setting if not */
+		if (phy14h != AX88772A_PHY14H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H,
+					     AX88772A_PHY14H_DEFAULT);
+		if (phy15h != AX88772A_PHY15H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H,
+					     AX88772A_PHY15H_DEFAULT);
+		if (phy16h != AX88772A_PHY16H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H,
+					     AX88772A_PHY16H_DEFAULT);
 	}
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
@@ -543,6 +578,15 @@ static const struct net_device_ops ax88772_netdev_ops = {
 static void ax88772_suspend(struct usbnet *dev)
 {
 	struct asix_common_private *priv = dev->driver_priv;
+	u16 medium;
+
+	/* Stop MAC operation */
+	medium = asix_read_medium_status(dev, 0);
+	medium &= ~AX_MEDIUM_RE;
+	asix_write_medium_mode(dev, medium, 0);
+
+	netdev_dbg(dev->net, "ax88772_suspend: medium=0x%04x\n",
+		   asix_read_medium_status(dev, 0));
 
 	/* Preserve BMCR for restoring */
 	priv->presvd_phy_bmcr =
@@ -577,6 +621,7 @@ static void ax88772_restore_phy(struct usbnet *dev)
 		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
 				     priv->presvd_phy_bmcr);
 
+		mii_nway_restart(&dev->mii);
 		priv->presvd_phy_advertise = 0;
 		priv->presvd_phy_bmcr = 0;
 	}
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1470383 — [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<sa9i2-5Ly-23@gated-at.bofh.it>
In reply to	#1470377

From: Grant Grundler <grundler@chromium.org>

The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.

The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.

Ignore the ret value since it's ignored in XXX_link_reset() functions.

Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index dbcdda2..cce2495 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -928,12 +928,9 @@ static int ax88178_reset(struct usbnet *dev)
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000,
 			ADVERTISE_1000FULL);
 
+	asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
-	if (ret < 0)
-		return ret;
-
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1470385 — [PATCH v3 1/5] net: asix: Add in_pm parameter

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 1/5] net: asix: Add in_pm parameter
Message-ID	<sa9i2-5Ly-11@gated-at.bofh.it>
In reply to	#1470377

From: Robert Foss <robert.foss@collabora.com>

From: Freddy Xin <freddy@asix.com.tw>

In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.

Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.

Reset HW in resume function to ensure the PHY works correctly.

Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix.h         |  40 +++-
 drivers/net/usb/asix_common.c  | 180 ++++++++++++----
 drivers/net/usb/asix_devices.c | 373 ++++++++++++++++++++++++++--------
 drivers/net/usb/ax88172a.c     |  29 +--
 4 files changed, 472 insertions(+), 150 deletions(-)

diff --git a/drivers/net/usb/asix.h b/drivers/net/usb/asix.h
index a2d3ea6..d109242 100644
--- a/drivers/net/usb/asix.h
+++ b/drivers/net/usb/asix.h
@@ -46,6 +46,7 @@
 #define AX_CMD_SET_SW_MII		0x06
 #define AX_CMD_READ_MII_REG		0x07
 #define AX_CMD_WRITE_MII_REG		0x08
+#define AX_CMD_STATMNGSTS_REG		0x09
 #define AX_CMD_SET_HW_MII		0x0a
 #define AX_CMD_READ_EEPROM		0x0b
 #define AX_CMD_WRITE_EEPROM		0x0c
@@ -71,6 +72,17 @@
 #define AX_CMD_SW_RESET			0x20
 #define AX_CMD_SW_PHY_STATUS		0x21
 #define AX_CMD_SW_PHY_SELECT		0x22
+#define AX_QCTCTRL			0x2A
+
+#define AX_CHIPCODE_MASK		0x70
+#define AX_AX88772_CHIPCODE		0x00
+#define AX_AX88772A_CHIPCODE		0x10
+#define AX_AX88772B_CHIPCODE		0x20
+#define AX_HOST_EN			0x01
+
+#define AX_PHYSEL_PSEL			0x01
+#define AX_PHYSEL_SSMII			0
+#define AX_PHYSEL_SSEN			0x10
 
 #define AX_PHY_SELECT_MASK		(BIT(3) | BIT(2))
 #define AX_PHY_SELECT_INTERNAL		0
@@ -173,6 +185,10 @@ struct asix_rx_fixup_info {
 };
 
 struct asix_common_private {
+	void (*resume)(struct usbnet *dev);
+	void (*suspend)(struct usbnet *dev);
+	u16 presvd_phy_advertise;
+	u16 presvd_phy_bmcr;
 	struct asix_rx_fixup_info rx_fixup_info;
 };
 
@@ -182,10 +198,10 @@ extern const struct driver_info ax88172a_info;
 #define FLAG_EEPROM_MAC		(1UL << 0)  /* init device MAC from eeprom */
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data);
+		  u16 size, void *data, int in_pm);
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data);
+		   u16 size, void *data, int in_pm);
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value,
 			  u16 index, u16 size, void *data);
@@ -197,27 +213,31 @@ int asix_rx_fixup_common(struct usbnet *dev, struct sk_buff *skb);
 struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 			      gfp_t flags);
 
-int asix_set_sw_mii(struct usbnet *dev);
-int asix_set_hw_mii(struct usbnet *dev);
+int asix_set_sw_mii(struct usbnet *dev, int in_pm);
+int asix_set_hw_mii(struct usbnet *dev, int in_pm);
 
 int asix_read_phy_addr(struct usbnet *dev, int internal);
 int asix_get_phy_addr(struct usbnet *dev);
 
-int asix_sw_reset(struct usbnet *dev, u8 flags);
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm);
 
-u16 asix_read_rx_ctl(struct usbnet *dev);
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode);
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm);
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
 
-u16 asix_read_medium_status(struct usbnet *dev);
-int asix_write_medium_mode(struct usbnet *dev, u16 mode);
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep);
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
 
 void asix_set_multicast(struct net_device *net);
 
 int asix_mdio_read(struct net_device *netdev, int phy_id, int loc);
 void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val);
 
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc);
+void asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc,
+			  int val);
+
 void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 
diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c
index 7de5ab5..25609ee 100644
--- a/drivers/net/usb/asix_common.c
+++ b/drivers/net/usb/asix_common.c
@@ -22,24 +22,49 @@
 #include "asix.h"
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data)
+		  u16 size, void *data, int in_pm)
 {
 	int ret;
-	ret = usbnet_read_cmd(dev, cmd,
-			       USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			       value, index, data, size);
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_read_cmd;
+	else
+		fn = usbnet_read_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to read reg index 0x%04x: %d\n",
+			    index, ret);
 
-	if (ret != size && ret >= 0)
-		return -EINVAL;
 	return ret;
 }
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data)
+		   u16 size, void *data, int in_pm)
 {
-	return usbnet_write_cmd(dev, cmd,
-				USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-				value, index, data, size);
+	int ret;
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, const void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_write_cmd;
+	else
+		fn = usbnet_write_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to write reg index 0x%04x: %d\n",
+			    index, ret);
+
+	return ret;
 }
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value, u16 index,
@@ -225,19 +250,20 @@ struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 	return skb;
 }
 
-int asix_set_sw_mii(struct usbnet *dev)
+int asix_set_sw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL, in_pm);
+
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable software MII access\n");
 	return ret;
 }
 
-int asix_set_hw_mii(struct usbnet *dev)
+int asix_set_hw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable hardware MII access\n");
 	return ret;
@@ -247,7 +273,7 @@ int asix_read_phy_addr(struct usbnet *dev, int internal)
 {
 	int offset = (internal ? 1 : 0);
 	u8 buf[2];
-	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf, 0);
 
 	netdev_dbg(dev->net, "asix_get_phy_addr()\n");
 
@@ -270,21 +296,21 @@ int asix_get_phy_addr(struct usbnet *dev)
 }
 
 
-int asix_sw_reset(struct usbnet *dev, u8 flags)
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm)
 {
 	int ret;
 
-        ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to send software reset: %02x\n", ret);
 
 	return ret;
 }
 
-u16 asix_read_rx_ctl(struct usbnet *dev)
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading RX_CTL register: %02x\n", ret);
@@ -295,12 +321,12 @@ out:
 	return ret;
 }
 
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_rx_ctl() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write RX_CTL mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -308,10 +334,11 @@ int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-u16 asix_read_medium_status(struct usbnet *dev)
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS,
+				0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading Medium Status register: %02x\n",
@@ -323,12 +350,13 @@ u16 asix_read_medium_status(struct usbnet *dev)
 
 }
 
-int asix_write_medium_mode(struct usbnet *dev, u16 mode)
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_medium_mode() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE,
+			     mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write Medium Mode mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -336,12 +364,12 @@ int asix_write_medium_mode(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep)
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_gpio() - value = 0x%04x\n", value);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write GPIO value 0x%04x: %02x\n",
 			   value, ret);
@@ -398,16 +426,23 @@ int asix_mdio_read(struct net_device *netdev, int phy_id, int loc)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res;
+	u8 smsr;
+	int i = 0;
 
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
+	do {
+		asix_set_sw_mii(dev, 0);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
-				(__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+				(__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
 	mutex_unlock(&dev->phy_mutex);
 
 	netdev_dbg(dev->net, "asix_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
-		   phy_id, loc, le16_to_cpu(res));
+			phy_id, loc, le16_to_cpu(res));
 
 	return le16_to_cpu(res);
 }
@@ -416,13 +451,71 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
-		   phy_id, loc, val);
+			phy_id, loc, val);
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		asix_set_sw_mii(dev, 0);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
+	mutex_unlock(&dev->phy_mutex);
+}
+
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res;
+	u8 smsr;
+	int i = 0;
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		asix_set_sw_mii(dev, 1);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
+		      (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
+	mutex_unlock(&dev->phy_mutex);
+
+	netdev_dbg(dev->net, "asix_mdio_read_nopm() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
+			phy_id, loc, le16_to_cpu(res));
+
+	return le16_to_cpu(res);
+}
+
+void
+asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc, int val)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
+
+	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
+			phy_id, loc, val);
+
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
-	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id, (__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+	do {
+		asix_set_sw_mii(dev, 1);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
 	mutex_unlock(&dev->phy_mutex);
 }
 
@@ -431,7 +524,8 @@ void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 	struct usbnet *dev = netdev_priv(net);
 	u8 opt;
 
-	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE, 0, 0, 1, &opt) < 0) {
+	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE,
+			  0, 0, 1, &opt, 0) < 0) {
 		wolinfo->supported = 0;
 		wolinfo->wolopts = 0;
 		return;
@@ -455,7 +549,7 @@ int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 		opt |= AX_MONITOR_MAGIC;
 
 	if (asix_write_cmd(dev, AX_CMD_WRITE_MONITOR_MODE,
-			      opt, 0, 0, NULL) < 0)
+			      opt, 0, 0, NULL, 0) < 0)
 		return -EINVAL;
 
 	return 0;
@@ -490,7 +584,7 @@ int asix_get_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	/* ax8817x returns 2 bytes from eeprom on read */
 	for (i = first_word; i <= last_word; i++) {
 		if (asix_read_cmd(dev, AX_CMD_READ_EEPROM, i, 0, 2,
-				  &(eeprom_buff[i - first_word])) < 0) {
+				  &eeprom_buff[i - first_word], 0) < 0) {
 			kfree(eeprom_buff);
 			return -EIO;
 		}
@@ -531,7 +625,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	   the EEPROM */
 	if (eeprom->offset & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, first_word, 0, 2,
-				    &(eeprom_buff[0]));
+				    &eeprom_buff[0], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", first_word);
 			goto free;
@@ -540,7 +634,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 
 	if ((eeprom->offset + eeprom->len) & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, last_word, 0, 2,
-				    &(eeprom_buff[last_word - first_word]));
+				    &eeprom_buff[last_word - first_word], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", last_word);
 			goto free;
@@ -550,7 +644,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	memcpy((u8 *)eeprom_buff + (eeprom->offset & 1), data, eeprom->len);
 
 	/* write data to EEPROM */
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to enable EEPROM write\n");
 		goto free;
@@ -561,7 +655,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		netdev_dbg(net, "write to EEPROM at offset 0x%02x, data 0x%04x\n",
 			   i, eeprom_buff[i - first_word]);
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_EEPROM, i,
-				     eeprom_buff[i - first_word], 0, NULL);
+				     eeprom_buff[i - first_word], 0, NULL, 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to write EEPROM at offset 0x%02x.\n",
 				   i);
@@ -570,7 +664,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		msleep(20);
 	}
 
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to disable EEPROM write\n");
 		goto free;
diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index 5cabefc..aaa4290 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -184,7 +184,7 @@ static int ax88172_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88172_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -213,18 +213,19 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	/* Toggle the GPIOs in a manufacturer/model specific way */
 	for (i = 2; i >= 0; i--) {
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS,
-				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL);
+				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL, 0);
 		if (ret < 0)
 			goto out;
 		msleep(5);
 	}
 
-	ret = asix_write_rx_ctl(dev, 0x80);
+	ret = asix_write_rx_ctl(dev, 0x80, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID,
+			    0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "read AX_CMD_READ_NODE_ID failed: %d\n",
 			   ret);
@@ -290,7 +291,7 @@ static int ax88772_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88772_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -298,78 +299,192 @@ static int ax88772_link_reset(struct usbnet *dev)
 static int ax88772_reset(struct usbnet *dev)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret;
+
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, 0);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
+	if (ret < 0)
+		goto out;
+
+	asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, 0);
+	if (ret < 0)
+		goto out;
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
 	u16 rx_ctl;
 
-	ret = asix_write_gpio(dev,
-			AX_GPIO_RSE | AX_GPIO_GPO_2 | AX_GPIO_GPO2EN, 5);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_2 |
+			      AX_GPIO_GPO2EN, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	embd_phy = ((asix_get_phy_addr(dev) & 0x1f) == 0x10 ? 1 : 0);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy,
+			     0, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
 		goto out;
 	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL);
-	if (ret < 0)
-		goto out;
+	if (embd_phy) {
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD, in_pm);
+		if (ret < 0)
+			goto out;
 
-	msleep(150);
+		usleep_range(10000, 11000);
 
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
-	if (ret < 0)
-		goto out;
+		ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+		if (ret < 0)
+			goto out;
 
-	msleep(150);
+		msleep(60);
 
-	if (embd_phy) {
-		ret = asix_sw_reset(dev, AX_SWRESET_IPRL);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	} else {
-		ret = asix_sw_reset(dev, AX_SWRESET_PRTE);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	}
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))){
+		ret = -EIO;
+		goto out;
+	}
+
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
+			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
+			     AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
+		goto out;
+	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_PRL);
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
+	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	rx_ctl = asix_read_medium_status(dev, in_pm);
+	netdev_dbg(dev->net,
+		   "Medium Status is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret, embd_phy;
+	u16 rx_ctl;
+	u8 chipcode = 0;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
-			ADVERTISE_ALL | ADVERTISE_CSMA);
-	mii_nway_restart(&dev->mii);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy |
+			     AX_PHYSEL_SSEN, 0, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
+		goto out;
+	}
+	usleep_range(10000, 11000);
 
-	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_IPRL, in_pm);
 	if (ret < 0)
 		goto out;
 
+	usleep_range(10000, 11000);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(160);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(200);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))) {
+		ret = -1;
+		goto out;
+	}
+
+	ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0,
+			    0, 1, &chipcode, in_pm);
+	if (ret < 0)
+		goto out;
+
+	if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772B_CHIPCODE) {
+		ret = asix_write_cmd(dev, AX_QCTCTRL, 0x8000, 0x8001,
+				     0, NULL, in_pm);
+		if (ret < 0) {
+			netdev_dbg(dev->net, "Write BQ setting failed: %d\n",
+				   ret);
+			goto out;
+		}
+	}
+
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 				AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-				AX88772_IPG2_DEFAULT, 0, NULL);
+				AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -378,20 +493,29 @@ static int ax88772_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, in_pm);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
+	if (ret < 0)
+		return ret;
+
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, in_pm);
 	netdev_dbg(dev->net,
 		   "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
@@ -400,7 +524,6 @@ static int ax88772_reset(struct usbnet *dev)
 
 out:
 	return ret;
-
 }
 
 static const struct net_device_ops ax88772_netdev_ops = {
@@ -415,11 +538,87 @@ static const struct net_device_ops ax88772_netdev_ops = {
 	.ndo_set_rx_mode        = asix_set_multicast,
 };
 
+static void ax88772_suspend(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	/* Preserve BMCR for restoring */
+	priv->presvd_phy_bmcr =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_BMCR);
+
+	/* Preserve ANAR for restoring */
+	priv->presvd_phy_advertise =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE);
+}
+
+static int asix_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->suspend)
+		priv->suspend(dev);
+
+	return usbnet_suspend(intf, message);
+}
+
+static void ax88772_restore_phy(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->presvd_phy_advertise) {
+		/* Restore Advertisement control reg */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE,
+				     priv->presvd_phy_advertise);
+
+		/* Restore BMCR */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
+				     priv->presvd_phy_bmcr);
+
+		priv->presvd_phy_advertise = 0;
+		priv->presvd_phy_bmcr = 0;
+	}
+}
+
+static void ax88772_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++)
+		if (!ax88772_hw_reset(dev, 1))
+			break;
+	ax88772_restore_phy(dev);
+}
+
+static void ax88772a_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++) {
+		if (!ax88772a_hw_reset(dev, 1))
+			break;
+	}
+
+	ax88772_restore_phy(dev);
+}
+
+static int asix_resume(struct usb_interface *intf)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->resume)
+		priv->resume(dev);
+
+	return usbnet_resume(intf);
+}
+
 static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 {
-	int ret, embd_phy, i;
-	u8 buf[ETH_ALEN];
+	int ret, i;
+	u8 buf[ETH_ALEN], chipcode = 0;
 	u32 phyid;
+	struct asix_common_private *priv;
 
 	usbnet_get_endpoints(dev,intf);
 
@@ -427,13 +626,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (dev->driver_info->data & FLAG_EEPROM_MAC) {
 		for (i = 0; i < (ETH_ALEN >> 1); i++) {
 			ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x04 + i,
-					0, 2, buf + i * 2);
+					    0, 2, buf + i * 2, 0);
 			if (ret < 0)
 				break;
 		}
 	} else {
 		ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID,
-				0, 0, ETH_ALEN, buf);
+				0, 0, ETH_ALEN, buf, 0);
 	}
 
 	if (ret < 0) {
@@ -456,16 +655,11 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
+	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
+	chipcode &= AX_CHIPCODE_MASK;
 
-	/* Reset the PHY to normal operation mode */
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
-	if (ret < 0) {
-		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
-		return ret;
-	}
-
-	ax88772_reset(dev);
+	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+					    ax88772a_hw_reset(dev, 0);
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);
@@ -482,6 +676,18 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (!dev->driver_priv)
 		return -ENOMEM;
 
+	priv = dev->driver_priv;
+
+	priv->presvd_phy_bmcr = 0;
+	priv->presvd_phy_advertise = 0;
+	if (chipcode == AX_AX88772_CHIPCODE) {
+		priv->resume = ax88772_resume;
+		priv->suspend = ax88772_suspend;
+	} else {
+		priv->resume = ax88772a_resume;
+		priv->suspend = ax88772_suspend;
+	}
+
 	return 0;
 }
 
@@ -593,12 +799,12 @@ static int ax88178_reset(struct usbnet *dev)
 	int gpio0 = 0;
 	u32 phyid;
 
-	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status);
+	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0);
 	netdev_dbg(dev->net, "GPIO Status: 0x%04x\n", status);
 
-	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL);
-	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom);
-	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL, 0);
+	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0);
+	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL, 0);
 
 	netdev_dbg(dev->net, "EEPROM index 0x17 is 0x%04x\n", eeprom);
 
@@ -614,15 +820,16 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "GPIO0: %d, PhyMode: %d\n", gpio0, data->phymode);
 
 	/* Power up external GigaPHY through AX88178 GPIO pin */
-	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 | AX_GPIO_GPO1EN, 40);
+	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 |
+			AX_GPIO_GPO1EN, 40, 0);
 	if ((le16_to_cpu(eeprom) >> 8) != 1) {
-		asix_write_gpio(dev, 0x003c, 30);
-		asix_write_gpio(dev, 0x001c, 300);
-		asix_write_gpio(dev, 0x003c, 30);
+		asix_write_gpio(dev, 0x003c, 30, 0);
+		asix_write_gpio(dev, 0x001c, 300, 0);
+		asix_write_gpio(dev, 0x003c, 30, 0);
 	} else {
 		netdev_dbg(dev->net, "gpio phymode == 1 path\n");
-		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30);
-		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30, 0);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30, 0);
 	}
 
 	/* Read PHYID register *AFTER* powering up PHY */
@@ -630,15 +837,15 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "PHYID=0x%08x\n", phyid);
 
 	/* Set AX88178 to enable MII/GMII/RGMII interface for external PHY */
-	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL, 0);
 
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
-	asix_write_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, 0, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL) {
 		marvell_phy_init(dev);
@@ -655,18 +862,18 @@ static int ax88178_reset(struct usbnet *dev)
 
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT);
+	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	if (ret < 0)
 		return ret;
 
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, 0);
 	if (ret < 0)
 		return ret;
 
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		return ret;
 
@@ -704,7 +911,7 @@ static int ax88178_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88178_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   speed, ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL && data->ledmode)
 		marvell_led_status(dev, speed);
@@ -733,15 +940,15 @@ static void ax88178_set_mfb(struct usbnet *dev)
 		mfb = AX_RX_CTL_MFB_16384;
 	}
 
-	rxctl = asix_read_rx_ctl(dev);
-	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb);
+	rxctl = asix_read_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb, 0);
 
-	medium = asix_read_medium_status(dev);
+	medium = asix_read_medium_status(dev, 0);
 	if (dev->net->mtu > 1500)
 		medium |= AX_MEDIUM_JFE;
 	else
 		medium &= ~AX_MEDIUM_JFE;
-	asix_write_medium_mode(dev, medium);
+	asix_write_medium_mode(dev, medium, 0);
 
 	if (dev->rx_urb_size > old_rx_urb_size)
 		usbnet_unlink_rx_urbs(dev);
@@ -790,7 +997,7 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	usbnet_get_endpoints(dev,intf);
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret);
 		return ret;
@@ -811,10 +1018,10 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88178_ethtool_ops;
 
 	/* Blink LEDS so users know driver saw dongle */
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
 	/* Asix framing packs multiple eth frames into a 2K usb bulk transfer */
@@ -877,7 +1084,7 @@ static const struct driver_info ax88772_info = {
 	.unbind = ax88772_unbind,
 	.status = asix_status,
 	.link_reset = ax88772_link_reset,
-	.reset = ax88772_link_reset,
+	.reset = ax88772_reset,
 	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
@@ -1005,7 +1212,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Lenovo U2L100P 10/100
 	USB_DEVICE (0x17ef, 0x7203),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	// ASIX AX88772B 10/100
 	USB_DEVICE (0x0b95, 0x772b),
@@ -1073,7 +1280,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Asus USB Ethernet Adapter
 	USB_DEVICE (0x0b95, 0x7e2b),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	/* ASIX 88172a demo board */
 	USB_DEVICE(0x0b95, 0x172a),
@@ -1095,8 +1302,8 @@ static struct usb_driver asix_driver = {
 	.name =		DRIVER_NAME,
 	.id_table =	products,
 	.probe =	usbnet_probe,
-	.suspend =	usbnet_suspend,
-	.resume =	usbnet_resume,
+	.suspend =	asix_suspend,
+	.resume =	asix_resume,
 	.disconnect =	usbnet_disconnect,
 	.supports_autosuspend = 1,
 	.disable_hub_initiated_lpm = 1,
diff --git a/drivers/net/usb/ax88172a.c b/drivers/net/usb/ax88172a.c
index 163a2c5..49a3bc1 100644
--- a/drivers/net/usb/ax88172a.c
+++ b/drivers/net/usb/ax88172a.c
@@ -81,7 +81,7 @@ static void ax88172a_adjust_link(struct net_device *netdev)
 	}
 
 	if (mode != priv->oldmode) {
-		asix_write_medium_mode(dev, mode);
+		asix_write_medium_mode(dev, mode, 0);
 		priv->oldmode = mode;
 		netdev_dbg(netdev, "speed %u duplex %d, setting mode to 0x%04x\n",
 			   phydev->speed, phydev->duplex, mode);
@@ -176,18 +176,19 @@ static int ax88172a_reset_phy(struct usbnet *dev, int embd_phy)
 {
 	int ret;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
 
-	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD,
+			    0);
 	if (ret < 0)
 		goto err;
 
@@ -213,7 +214,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->driver_priv = priv;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read MAC address: %d\n", ret);
 		goto free;
@@ -224,7 +225,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88172a_ethtool_ops;
 
 	/* are we using the internal or the external phy? */
-	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf);
+	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read software interface selection register: %d\n",
 			   ret);
@@ -303,20 +304,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	ax88172a_reset_phy(dev, priv->use_embdphy);
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+	ret = asix_write_rx_ctl(dev, 0x0000, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
 
 	msleep(150);
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-			     AX88772_IPG2_DEFAULT, 0, NULL);
+			     AX88772_IPG2_DEFAULT, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -325,20 +326,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-			     data->mac_addr);
+			     data->mac_addr, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, 0);
 	netdev_dbg(dev->net, "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-- 
git-series 0.8.10

[toc] | [prev] | [next] | [standalone]

#1470387 — [PATCH v3 3/5] net: asix: Fix AX88772x resume failures

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 3/5] net: asix: Fix AX88772x resume failures
Message-ID	<sa9i2-5Ly-27@gated-at.bofh.it>
In reply to	#1470377

From: Robert Foss <robert.foss@collabora.com>

From: Allan Chou <allan@asix.com.tw>

The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY

Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 47 ++++++++++++++++++++++++++++++++++-
 1 file changed, 46 insertions(+), 1 deletion(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index ebeb730..083dc2e 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -35,6 +35,15 @@
 
 #define	PHY_MODE_RTL8211CL	0x000C
 
+#define AX88772A_PHY14H		0x14
+#define AX88772A_PHY14H_DEFAULT 0x442C
+
+#define AX88772A_PHY15H		0x15
+#define AX88772A_PHY15H_DEFAULT 0x03C8
+
+#define AX88772A_PHY16H		0x16
+#define AX88772A_PHY16H_DEFAULT 0x4044
+
 struct ax88172_int_data {
 	__le16 res1;
 	u8 link;
@@ -424,7 +433,7 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
-	u16 rx_ctl;
+	u16 rx_ctl, phy14h, phy15h, phy16h;
 	u8 chipcode = 0;
 
 	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
@@ -482,6 +491,32 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 				   ret);
 			goto out;
 		}
+	} else if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772A_CHIPCODE) {
+		/* Check if the PHY registers have default settings */
+		phy14h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H);
+		phy15h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H);
+		phy16h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H);
+
+		netdev_dbg(dev->net,
+			   "772a_hw_reset: MR20=0x%x MR21=0x%x MR22=0x%x\n",
+			   phy14h, phy15h, phy16h);
+
+		/* Restore PHY registers default setting if not */
+		if (phy14h != AX88772A_PHY14H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H,
+					     AX88772A_PHY14H_DEFAULT);
+		if (phy15h != AX88772A_PHY15H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H,
+					     AX88772A_PHY15H_DEFAULT);
+		if (phy16h != AX88772A_PHY16H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H,
+					     AX88772A_PHY16H_DEFAULT);
 	}
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
@@ -543,6 +578,15 @@ static const struct net_device_ops ax88772_netdev_ops = {
 static void ax88772_suspend(struct usbnet *dev)
 {
 	struct asix_common_private *priv = dev->driver_priv;
+	u16 medium;
+
+	/* Stop MAC operation */
+	medium = asix_read_medium_status(dev, 0);
+	medium &= ~AX_MEDIUM_RE;
+	asix_write_medium_mode(dev, medium, 0);
+
+	netdev_dbg(dev->net, "ax88772_suspend: medium=0x%04x\n",
+		   asix_read_medium_status(dev, 0));
 
 	/* Preserve BMCR for restoring */
 	priv->presvd_phy_bmcr =
@@ -577,6 +621,7 @@ static void ax88772_restore_phy(struct usbnet *dev)
 		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
 				     priv->presvd_phy_bmcr);
 
+		mii_nway_restart(&dev->mii);
 		priv->presvd_phy_advertise = 0;
 		priv->presvd_phy_bmcr = 0;
 	}
-- 
git-series 0.8.10

[toc] | [prev] | [next] | [standalone]

#1470388 — [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<sa9i2-5Ly-29@gated-at.bofh.it>
In reply to	#1470377

From: Robert Foss <robert.foss@collabora.com>

From: Grant Grundler <grundler@chromium.org>

The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.

The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.

Ignore the ret value since it's ignored in XXX_link_reset() functions.

Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index dbcdda2..cce2495 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -928,12 +928,9 @@ static int ax88178_reset(struct usbnet *dev)
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000,
 			ADVERTISE_1000FULL);
 
+	asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
-	if (ret < 0)
-		return ret;
-
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-- 
git-series 0.8.10

[toc] | [prev] | [next] | [standalone]

#1474564 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	Robert Foss <robert.foss@collabora.com>
Date	2016-09-01 18:50 +0200
Subject	Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<scDlF-4lf-69@gated-at.bofh.it>
In reply to	#1470388


On 2016-09-01 12:43 PM, Eric Dumazet wrote:
> On Mon, 2016-08-29 at 09:32 -0400, robert.foss@collabora.com wrote:
>> From: Robert Foss <robert.foss@collabora.com>
>>
>> From: Grant Grundler <grundler@chromium.org>
>>
>> The miii_nway_restart() causes a PHY link change activity and
>> ax88772_link_reset will be called. link_reset will set
>> AX_CMD_WRITE_MEDIUM_MODE register correctly.
>>
>> The asix_write_medium_mode in reset() fills in a default value to the register
>> which may be different from the negotiation result. So do this first.
>>
>> Ignore the ret value since it's ignored in XXX_link_reset() functions.
>>
>> Signed-off-by: Grant Grundler <grundler@google.com>
>> Signed-off-by: Robert Foss <robert.foss@collabora.com>
>> Tested-by: Robert Foss <robert.foss@collabora.com>
>> ---
>
> This is _really_ confusing Robert.
>
> Why having two 'From:' clauses ?
>
> Who wrote the patch in the first place ? You or Grant ?

I'm not quite sure how the first From line was added, it
should not have been.
Grant Grundler is most definitely the author.

Would you like me to resubmit in v++ and make sure that it has been 
corrected?

>
>
>
> End result is :
>
> commit 535baf8588d04b177cb33700f81499f2b5203c2d
> Author: Robert Foss <robert.foss@collabora.com>
> Date:   Mon Aug 29 09:32:19 2016 -0400
>
>     net: asix: autoneg will set WRITE_MEDIUM reg
>
>     From: Grant Grundler <grundler@chromium.org>
>
>     The miii_nway_restart() causes a PHY link change activity and
>     ax88772_link_reset will be called. link_reset will set
>     AX_CMD_WRITE_MEDIUM_MODE register correctly.
>
>     The asix_write_medium_mode in reset() fills in a default value to the register
>     which may be different from the negotiation result. So do this first.
>
>     Ignore the ret value since it's ignored in XXX_link_reset() functions.
>
>     Signed-off-by: Grant Grundler <grundler@google.com>
>     Signed-off-by: Robert Foss <robert.foss@collabora.com>
>     Tested-by: Robert Foss <robert.foss@collabora.com>
>     Signed-off-by: David S. Miller <davem@davemloft.net>
>
>
>
> I guess Grant wrote the patch, but attribution is wrong.
>
>

[toc] | [prev] | [next] | [standalone]

#1474576 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	Eric Dumazet <eric.dumazet@gmail.com>
Date	2016-09-01 23:10 +0200
Subject	Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<scHpf-70l-3@gated-at.bofh.it>
In reply to	#1474564

On Thu, 2016-09-01 at 12:47 -0400, Robert Foss wrote:

> I'm not quite sure how the first From line was added, it
> should not have been.
> Grant Grundler is most definitely the author.
> 
> Would you like me to resubmit in v++ and make sure that it has been 
> corrected?

This is too late, patches are already merged in David Miller net-next
tree.

These kinds of errors can not be fixed, we have to be very careful at
submission/review time.

I guess Grant does not care, but some contributors, especially new ones
would like to get proper attribution.

Thanks.

[toc] | [prev] | [next] | [standalone]

#1477616 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	Grant Grundler <grundler@google.com>
Date	2016-09-06 18:50 +0200
Subject	Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<serJo-4tA-27@gated-at.bofh.it>
In reply to	#1474576

On Thu, Sep 1, 2016 at 10:02 AM, Eric Dumazet <eric.dumazet@gmail.com> wrote:
> On Thu, 2016-09-01 at 12:47 -0400, Robert Foss wrote:
>
>> I'm not quite sure how the first From line was added, it
>> should not have been.
>> Grant Grundler is most definitely the author.
>>
>> Would you like me to resubmit in v++ and make sure that it has been
>> corrected?
>
> This is too late, patches are already merged in David Miller net-next
> tree.
>
> These kinds of errors can not be fixed, we have to be very careful at
> submission/review time.
>
> I guess Grant does not care, but some contributors, especially new ones
> would like to get proper attribution.

I do not mind. Robert will get email about bugs instead of me. :D

cheers,
grant

>
> Thanks.
>
>

[toc] | [prev] | [next] | [standalone]

#1477834 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	Robert Foss <robert.foss@collabora.com>
Date	2016-09-06 23:50 +0200
Subject	Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<sewpH-7zd-1@gated-at.bofh.it>
In reply to	#1477616


On 2016-09-06 12:41 PM, Grant Grundler wrote:
> On Thu, Sep 1, 2016 at 10:02 AM, Eric Dumazet <eric.dumazet@gmail.com> wrote:
>> On Thu, 2016-09-01 at 12:47 -0400, Robert Foss wrote:
>>
>>> I'm not quite sure how the first From line was added, it
>>> should not have been.
>>> Grant Grundler is most definitely the author.
>>>
>>> Would you like me to resubmit in v++ and make sure that it has been
>>> corrected?
>>
>> This is too late, patches are already merged in David Miller net-next
>> tree.
>>
>> These kinds of errors can not be fixed, we have to be very careful at
>> submission/review time.
>>
>> I guess Grant does not care, but some contributors, especially new ones
>> would like to get proper attribution.
>
> I do not mind. Robert will get email about bugs instead of me. :D

Thanks Grant, sorry about the mixup!


Rob.

[toc] | [prev] | [next] | [standalone]

#1474565 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	Eric Dumazet <eric.dumazet@gmail.com>
Date	2016-09-01 18:50 +0200
Subject	Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<scDlF-4lf-67@gated-at.bofh.it>
In reply to	#1470388

On Mon, 2016-08-29 at 09:32 -0400, robert.foss@collabora.com wrote:
> From: Robert Foss <robert.foss@collabora.com>
> 
> From: Grant Grundler <grundler@chromium.org>
> 
> The miii_nway_restart() causes a PHY link change activity and
> ax88772_link_reset will be called. link_reset will set
> AX_CMD_WRITE_MEDIUM_MODE register correctly.
> 
> The asix_write_medium_mode in reset() fills in a default value to the register
> which may be different from the negotiation result. So do this first.
> 
> Ignore the ret value since it's ignored in XXX_link_reset() functions.
> 
> Signed-off-by: Grant Grundler <grundler@google.com>
> Signed-off-by: Robert Foss <robert.foss@collabora.com>
> Tested-by: Robert Foss <robert.foss@collabora.com>
> ---

This is _really_ confusing Robert.

Why having two 'From:' clauses ?

Who wrote the patch in the first place ? You or Grant ?



End result is :

commit 535baf8588d04b177cb33700f81499f2b5203c2d
Author: Robert Foss <robert.foss@collabora.com>
Date:   Mon Aug 29 09:32:19 2016 -0400

    net: asix: autoneg will set WRITE_MEDIUM reg
    
    From: Grant Grundler <grundler@chromium.org>
    
    The miii_nway_restart() causes a PHY link change activity and
    ax88772_link_reset will be called. link_reset will set
    AX_CMD_WRITE_MEDIUM_MODE register correctly.
    
    The asix_write_medium_mode in reset() fills in a default value to the register
    which may be different from the negotiation result. So do this first.
    
    Ignore the ret value since it's ignored in XXX_link_reset() functions.
    
    Signed-off-by: Grant Grundler <grundler@google.com>
    Signed-off-by: Robert Foss <robert.foss@collabora.com>
    Tested-by: Robert Foss <robert.foss@collabora.com>
    Signed-off-by: David S. Miller <davem@davemloft.net>



I guess Grant wrote the patch, but attribution is wrong.

[toc] | [prev] | [next] | [standalone]

#1470389 — [PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected
Message-ID	<sa9i2-5Ly-21@gated-at.bofh.it>
In reply to	#1470377

From: Vincent Palatin <vpalatin@chromium.org>

Check the answers from the USB stack and avoid re-sending multiple times
the request if the device has disappeared.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_common.c  | 56 +++++++++++++++++++++++++++++++++---------
 drivers/net/usb/asix_devices.c |  2 ++
 2 files changed, 46 insertions(+), 12 deletions(-)

diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c
index 25609ee..f79eb12 100644
--- a/drivers/net/usb/asix_common.c
+++ b/drivers/net/usb/asix_common.c
@@ -428,13 +428,21 @@ int asix_mdio_read(struct net_device *netdev, int phy_id, int loc)
 	__le16 res;
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 0);
+		ret = asix_set_sw_mii(dev, 0);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
 
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
 				(__u16)loc, 2, &res, 0);
@@ -453,16 +461,24 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
 	__le16 res = cpu_to_le16(val);
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
 			phy_id, loc, val);
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 0);
+		ret = asix_set_sw_mii(dev, 0);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return;
+	}
 
 	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
 		       (__u16)loc, 2, &res, 0);
@@ -476,13 +492,21 @@ int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
 	__le16 res;
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 1);
+		ret = asix_set_sw_mii(dev, 1);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
 
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
 		      (__u16)loc, 2, &res, 1);
@@ -502,16 +526,24 @@ asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc, int val)
 	__le16 res = cpu_to_le16(val);
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
 			phy_id, loc, val);
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 1);
+		ret = asix_set_sw_mii(dev, 1);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return;
+	}
 
 	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
 		       (__u16)loc, 2, &res, 1);
diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index aaa4290..ebeb730 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -79,6 +79,8 @@ static u32 asix_get_phyid(struct usbnet *dev)
 	/* Poll for the rare case the FW or phy isn't ready yet.  */
 	for (i = 0; i < 100; i++) {
 		phy_reg = asix_mdio_read(dev->net, dev->mii.phy_id, MII_PHYSID1);
+		if (phy_reg < 0)
+			return 0;
 		if (phy_reg != 0 && phy_reg != 0xFFFF)
 			break;
 		mdelay(1);
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1470391 — [PATCH v3 1/5] net: asix: Add in_pm parameter

From	robert.foss@collabora.com
Date	2016-08-25 22:20 +0200
Subject	[PATCH v3 1/5] net: asix: Add in_pm parameter
Message-ID	<sa9i2-5Ly-31@gated-at.bofh.it>
In reply to	#1470377

From: Freddy Xin <freddy@asix.com.tw>

In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.

Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.

Reset HW in resume function to ensure the PHY works correctly.

Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix.h         |  40 +++--
 drivers/net/usb/asix_common.c  | 180 +++++++++++++++-----
 drivers/net/usb/asix_devices.c | 373 ++++++++++++++++++++++++++++++++---------
 drivers/net/usb/ax88172a.c     |  29 ++--
 4 files changed, 472 insertions(+), 150 deletions(-)

diff --git a/drivers/net/usb/asix.h b/drivers/net/usb/asix.h
index a2d3ea6..d109242 100644
--- a/drivers/net/usb/asix.h
+++ b/drivers/net/usb/asix.h
@@ -46,6 +46,7 @@
 #define AX_CMD_SET_SW_MII		0x06
 #define AX_CMD_READ_MII_REG		0x07
 #define AX_CMD_WRITE_MII_REG		0x08
+#define AX_CMD_STATMNGSTS_REG		0x09
 #define AX_CMD_SET_HW_MII		0x0a
 #define AX_CMD_READ_EEPROM		0x0b
 #define AX_CMD_WRITE_EEPROM		0x0c
@@ -71,6 +72,17 @@
 #define AX_CMD_SW_RESET			0x20
 #define AX_CMD_SW_PHY_STATUS		0x21
 #define AX_CMD_SW_PHY_SELECT		0x22
+#define AX_QCTCTRL			0x2A
+
+#define AX_CHIPCODE_MASK		0x70
+#define AX_AX88772_CHIPCODE		0x00
+#define AX_AX88772A_CHIPCODE		0x10
+#define AX_AX88772B_CHIPCODE		0x20
+#define AX_HOST_EN			0x01
+
+#define AX_PHYSEL_PSEL			0x01
+#define AX_PHYSEL_SSMII			0
+#define AX_PHYSEL_SSEN			0x10
 
 #define AX_PHY_SELECT_MASK		(BIT(3) | BIT(2))
 #define AX_PHY_SELECT_INTERNAL		0
@@ -173,6 +185,10 @@ struct asix_rx_fixup_info {
 };
 
 struct asix_common_private {
+	void (*resume)(struct usbnet *dev);
+	void (*suspend)(struct usbnet *dev);
+	u16 presvd_phy_advertise;
+	u16 presvd_phy_bmcr;
 	struct asix_rx_fixup_info rx_fixup_info;
 };
 
@@ -182,10 +198,10 @@ extern const struct driver_info ax88172a_info;
 #define FLAG_EEPROM_MAC		(1UL << 0)  /* init device MAC from eeprom */
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data);
+		  u16 size, void *data, int in_pm);
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data);
+		   u16 size, void *data, int in_pm);
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value,
 			  u16 index, u16 size, void *data);
@@ -197,27 +213,31 @@ int asix_rx_fixup_common(struct usbnet *dev, struct sk_buff *skb);
 struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 			      gfp_t flags);
 
-int asix_set_sw_mii(struct usbnet *dev);
-int asix_set_hw_mii(struct usbnet *dev);
+int asix_set_sw_mii(struct usbnet *dev, int in_pm);
+int asix_set_hw_mii(struct usbnet *dev, int in_pm);
 
 int asix_read_phy_addr(struct usbnet *dev, int internal);
 int asix_get_phy_addr(struct usbnet *dev);
 
-int asix_sw_reset(struct usbnet *dev, u8 flags);
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm);
 
-u16 asix_read_rx_ctl(struct usbnet *dev);
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode);
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm);
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
 
-u16 asix_read_medium_status(struct usbnet *dev);
-int asix_write_medium_mode(struct usbnet *dev, u16 mode);
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep);
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
 
 void asix_set_multicast(struct net_device *net);
 
 int asix_mdio_read(struct net_device *netdev, int phy_id, int loc);
 void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val);
 
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc);
+void asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc,
+			  int val);
+
 void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 
diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c
index 7de5ab5..25609ee 100644
--- a/drivers/net/usb/asix_common.c
+++ b/drivers/net/usb/asix_common.c
@@ -22,24 +22,49 @@
 #include "asix.h"
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data)
+		  u16 size, void *data, int in_pm)
 {
 	int ret;
-	ret = usbnet_read_cmd(dev, cmd,
-			       USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			       value, index, data, size);
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_read_cmd;
+	else
+		fn = usbnet_read_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to read reg index 0x%04x: %d\n",
+			    index, ret);
 
-	if (ret != size && ret >= 0)
-		return -EINVAL;
 	return ret;
 }
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data)
+		   u16 size, void *data, int in_pm)
 {
-	return usbnet_write_cmd(dev, cmd,
-				USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-				value, index, data, size);
+	int ret;
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, const void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_write_cmd;
+	else
+		fn = usbnet_write_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to write reg index 0x%04x: %d\n",
+			    index, ret);
+
+	return ret;
 }
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value, u16 index,
@@ -225,19 +250,20 @@ struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 	return skb;
 }
 
-int asix_set_sw_mii(struct usbnet *dev)
+int asix_set_sw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL, in_pm);
+
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable software MII access\n");
 	return ret;
 }
 
-int asix_set_hw_mii(struct usbnet *dev)
+int asix_set_hw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable hardware MII access\n");
 	return ret;
@@ -247,7 +273,7 @@ int asix_read_phy_addr(struct usbnet *dev, int internal)
 {
 	int offset = (internal ? 1 : 0);
 	u8 buf[2];
-	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf, 0);
 
 	netdev_dbg(dev->net, "asix_get_phy_addr()\n");
 
@@ -270,21 +296,21 @@ int asix_get_phy_addr(struct usbnet *dev)
 }
 
 
-int asix_sw_reset(struct usbnet *dev, u8 flags)
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm)
 {
 	int ret;
 
-        ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to send software reset: %02x\n", ret);
 
 	return ret;
 }
 
-u16 asix_read_rx_ctl(struct usbnet *dev)
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading RX_CTL register: %02x\n", ret);
@@ -295,12 +321,12 @@ out:
 	return ret;
 }
 
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_rx_ctl() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write RX_CTL mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -308,10 +334,11 @@ int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-u16 asix_read_medium_status(struct usbnet *dev)
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS,
+				0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading Medium Status register: %02x\n",
@@ -323,12 +350,13 @@ u16 asix_read_medium_status(struct usbnet *dev)
 
 }
 
-int asix_write_medium_mode(struct usbnet *dev, u16 mode)
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_medium_mode() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE,
+			     mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write Medium Mode mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -336,12 +364,12 @@ int asix_write_medium_mode(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep)
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_gpio() - value = 0x%04x\n", value);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write GPIO value 0x%04x: %02x\n",
 			   value, ret);
@@ -398,16 +426,23 @@ int asix_mdio_read(struct net_device *netdev, int phy_id, int loc)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res;
+	u8 smsr;
+	int i = 0;
 
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
+	do {
+		asix_set_sw_mii(dev, 0);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
-				(__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+				(__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
 	mutex_unlock(&dev->phy_mutex);
 
 	netdev_dbg(dev->net, "asix_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
-		   phy_id, loc, le16_to_cpu(res));
+			phy_id, loc, le16_to_cpu(res));
 
 	return le16_to_cpu(res);
 }
@@ -416,13 +451,71 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
-		   phy_id, loc, val);
+			phy_id, loc, val);
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		asix_set_sw_mii(dev, 0);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
+	mutex_unlock(&dev->phy_mutex);
+}
+
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res;
+	u8 smsr;
+	int i = 0;
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		asix_set_sw_mii(dev, 1);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
+		      (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
+	mutex_unlock(&dev->phy_mutex);
+
+	netdev_dbg(dev->net, "asix_mdio_read_nopm() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
+			phy_id, loc, le16_to_cpu(res));
+
+	return le16_to_cpu(res);
+}
+
+void
+asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc, int val)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
+
+	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
+			phy_id, loc, val);
+
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
-	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id, (__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+	do {
+		asix_set_sw_mii(dev, 1);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
 	mutex_unlock(&dev->phy_mutex);
 }
 
@@ -431,7 +524,8 @@ void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 	struct usbnet *dev = netdev_priv(net);
 	u8 opt;
 
-	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE, 0, 0, 1, &opt) < 0) {
+	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE,
+			  0, 0, 1, &opt, 0) < 0) {
 		wolinfo->supported = 0;
 		wolinfo->wolopts = 0;
 		return;
@@ -455,7 +549,7 @@ int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 		opt |= AX_MONITOR_MAGIC;
 
 	if (asix_write_cmd(dev, AX_CMD_WRITE_MONITOR_MODE,
-			      opt, 0, 0, NULL) < 0)
+			      opt, 0, 0, NULL, 0) < 0)
 		return -EINVAL;
 
 	return 0;
@@ -490,7 +584,7 @@ int asix_get_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	/* ax8817x returns 2 bytes from eeprom on read */
 	for (i = first_word; i <= last_word; i++) {
 		if (asix_read_cmd(dev, AX_CMD_READ_EEPROM, i, 0, 2,
-				  &(eeprom_buff[i - first_word])) < 0) {
+				  &eeprom_buff[i - first_word], 0) < 0) {
 			kfree(eeprom_buff);
 			return -EIO;
 		}
@@ -531,7 +625,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	   the EEPROM */
 	if (eeprom->offset & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, first_word, 0, 2,
-				    &(eeprom_buff[0]));
+				    &eeprom_buff[0], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", first_word);
 			goto free;
@@ -540,7 +634,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 
 	if ((eeprom->offset + eeprom->len) & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, last_word, 0, 2,
-				    &(eeprom_buff[last_word - first_word]));
+				    &eeprom_buff[last_word - first_word], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", last_word);
 			goto free;
@@ -550,7 +644,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	memcpy((u8 *)eeprom_buff + (eeprom->offset & 1), data, eeprom->len);
 
 	/* write data to EEPROM */
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to enable EEPROM write\n");
 		goto free;
@@ -561,7 +655,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		netdev_dbg(net, "write to EEPROM at offset 0x%02x, data 0x%04x\n",
 			   i, eeprom_buff[i - first_word]);
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_EEPROM, i,
-				     eeprom_buff[i - first_word], 0, NULL);
+				     eeprom_buff[i - first_word], 0, NULL, 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to write EEPROM at offset 0x%02x.\n",
 				   i);
@@ -570,7 +664,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		msleep(20);
 	}
 
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to disable EEPROM write\n");
 		goto free;
diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index 5cabefc..aaa4290 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -184,7 +184,7 @@ static int ax88172_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88172_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -213,18 +213,19 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	/* Toggle the GPIOs in a manufacturer/model specific way */
 	for (i = 2; i >= 0; i--) {
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS,
-				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL);
+				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL, 0);
 		if (ret < 0)
 			goto out;
 		msleep(5);
 	}
 
-	ret = asix_write_rx_ctl(dev, 0x80);
+	ret = asix_write_rx_ctl(dev, 0x80, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID,
+			    0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "read AX_CMD_READ_NODE_ID failed: %d\n",
 			   ret);
@@ -290,7 +291,7 @@ static int ax88772_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88772_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -298,78 +299,192 @@ static int ax88772_link_reset(struct usbnet *dev)
 static int ax88772_reset(struct usbnet *dev)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret;
+
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, 0);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
+	if (ret < 0)
+		goto out;
+
+	asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, 0);
+	if (ret < 0)
+		goto out;
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
 	u16 rx_ctl;
 
-	ret = asix_write_gpio(dev,
-			AX_GPIO_RSE | AX_GPIO_GPO_2 | AX_GPIO_GPO2EN, 5);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_2 |
+			      AX_GPIO_GPO2EN, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	embd_phy = ((asix_get_phy_addr(dev) & 0x1f) == 0x10 ? 1 : 0);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy,
+			     0, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
 		goto out;
 	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL);
-	if (ret < 0)
-		goto out;
+	if (embd_phy) {
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD, in_pm);
+		if (ret < 0)
+			goto out;
 
-	msleep(150);
+		usleep_range(10000, 11000);
 
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
-	if (ret < 0)
-		goto out;
+		ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+		if (ret < 0)
+			goto out;
 
-	msleep(150);
+		msleep(60);
 
-	if (embd_phy) {
-		ret = asix_sw_reset(dev, AX_SWRESET_IPRL);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	} else {
-		ret = asix_sw_reset(dev, AX_SWRESET_PRTE);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	}
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))){
+		ret = -EIO;
+		goto out;
+	}
+
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
+			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
+			     AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
+		goto out;
+	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_PRL);
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
+	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	rx_ctl = asix_read_medium_status(dev, in_pm);
+	netdev_dbg(dev->net,
+		   "Medium Status is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret, embd_phy;
+	u16 rx_ctl;
+	u8 chipcode = 0;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
-			ADVERTISE_ALL | ADVERTISE_CSMA);
-	mii_nway_restart(&dev->mii);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy |
+			     AX_PHYSEL_SSEN, 0, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
+		goto out;
+	}
+	usleep_range(10000, 11000);
 
-	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_IPRL, in_pm);
 	if (ret < 0)
 		goto out;
 
+	usleep_range(10000, 11000);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(160);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(200);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))) {
+		ret = -1;
+		goto out;
+	}
+
+	ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0,
+			    0, 1, &chipcode, in_pm);
+	if (ret < 0)
+		goto out;
+
+	if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772B_CHIPCODE) {
+		ret = asix_write_cmd(dev, AX_QCTCTRL, 0x8000, 0x8001,
+				     0, NULL, in_pm);
+		if (ret < 0) {
+			netdev_dbg(dev->net, "Write BQ setting failed: %d\n",
+				   ret);
+			goto out;
+		}
+	}
+
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 				AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-				AX88772_IPG2_DEFAULT, 0, NULL);
+				AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -378,20 +493,29 @@ static int ax88772_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, in_pm);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
+	if (ret < 0)
+		return ret;
+
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, in_pm);
 	netdev_dbg(dev->net,
 		   "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
@@ -400,7 +524,6 @@ static int ax88772_reset(struct usbnet *dev)
 
 out:
 	return ret;
-
 }
 
 static const struct net_device_ops ax88772_netdev_ops = {
@@ -415,11 +538,87 @@ static const struct net_device_ops ax88772_netdev_ops = {
 	.ndo_set_rx_mode        = asix_set_multicast,
 };
 
+static void ax88772_suspend(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	/* Preserve BMCR for restoring */
+	priv->presvd_phy_bmcr =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_BMCR);
+
+	/* Preserve ANAR for restoring */
+	priv->presvd_phy_advertise =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE);
+}
+
+static int asix_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->suspend)
+		priv->suspend(dev);
+
+	return usbnet_suspend(intf, message);
+}
+
+static void ax88772_restore_phy(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->presvd_phy_advertise) {
+		/* Restore Advertisement control reg */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE,
+				     priv->presvd_phy_advertise);
+
+		/* Restore BMCR */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
+				     priv->presvd_phy_bmcr);
+
+		priv->presvd_phy_advertise = 0;
+		priv->presvd_phy_bmcr = 0;
+	}
+}
+
+static void ax88772_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++)
+		if (!ax88772_hw_reset(dev, 1))
+			break;
+	ax88772_restore_phy(dev);
+}
+
+static void ax88772a_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++) {
+		if (!ax88772a_hw_reset(dev, 1))
+			break;
+	}
+
+	ax88772_restore_phy(dev);
+}
+
+static int asix_resume(struct usb_interface *intf)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->resume)
+		priv->resume(dev);
+
+	return usbnet_resume(intf);
+}
+
 static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 {
-	int ret, embd_phy, i;
-	u8 buf[ETH_ALEN];
+	int ret, i;
+	u8 buf[ETH_ALEN], chipcode = 0;
 	u32 phyid;
+	struct asix_common_private *priv;
 
 	usbnet_get_endpoints(dev,intf);
 
@@ -427,13 +626,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (dev->driver_info->data & FLAG_EEPROM_MAC) {
 		for (i = 0; i < (ETH_ALEN >> 1); i++) {
 			ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x04 + i,
-					0, 2, buf + i * 2);
+					    0, 2, buf + i * 2, 0);
 			if (ret < 0)
 				break;
 		}
 	} else {
 		ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID,
-				0, 0, ETH_ALEN, buf);
+				0, 0, ETH_ALEN, buf, 0);
 	}
 
 	if (ret < 0) {
@@ -456,16 +655,11 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
+	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
+	chipcode &= AX_CHIPCODE_MASK;
 
-	/* Reset the PHY to normal operation mode */
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
-	if (ret < 0) {
-		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
-		return ret;
-	}
-
-	ax88772_reset(dev);
+	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+					    ax88772a_hw_reset(dev, 0);
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);
@@ -482,6 +676,18 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (!dev->driver_priv)
 		return -ENOMEM;
 
+	priv = dev->driver_priv;
+
+	priv->presvd_phy_bmcr = 0;
+	priv->presvd_phy_advertise = 0;
+	if (chipcode == AX_AX88772_CHIPCODE) {
+		priv->resume = ax88772_resume;
+		priv->suspend = ax88772_suspend;
+	} else {
+		priv->resume = ax88772a_resume;
+		priv->suspend = ax88772_suspend;
+	}
+
 	return 0;
 }
 
@@ -593,12 +799,12 @@ static int ax88178_reset(struct usbnet *dev)
 	int gpio0 = 0;
 	u32 phyid;
 
-	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status);
+	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0);
 	netdev_dbg(dev->net, "GPIO Status: 0x%04x\n", status);
 
-	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL);
-	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom);
-	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL, 0);
+	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0);
+	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL, 0);
 
 	netdev_dbg(dev->net, "EEPROM index 0x17 is 0x%04x\n", eeprom);
 
@@ -614,15 +820,16 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "GPIO0: %d, PhyMode: %d\n", gpio0, data->phymode);
 
 	/* Power up external GigaPHY through AX88178 GPIO pin */
-	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 | AX_GPIO_GPO1EN, 40);
+	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 |
+			AX_GPIO_GPO1EN, 40, 0);
 	if ((le16_to_cpu(eeprom) >> 8) != 1) {
-		asix_write_gpio(dev, 0x003c, 30);
-		asix_write_gpio(dev, 0x001c, 300);
-		asix_write_gpio(dev, 0x003c, 30);
+		asix_write_gpio(dev, 0x003c, 30, 0);
+		asix_write_gpio(dev, 0x001c, 300, 0);
+		asix_write_gpio(dev, 0x003c, 30, 0);
 	} else {
 		netdev_dbg(dev->net, "gpio phymode == 1 path\n");
-		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30);
-		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30, 0);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30, 0);
 	}
 
 	/* Read PHYID register *AFTER* powering up PHY */
@@ -630,15 +837,15 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "PHYID=0x%08x\n", phyid);
 
 	/* Set AX88178 to enable MII/GMII/RGMII interface for external PHY */
-	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL, 0);
 
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
-	asix_write_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, 0, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL) {
 		marvell_phy_init(dev);
@@ -655,18 +862,18 @@ static int ax88178_reset(struct usbnet *dev)
 
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT);
+	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	if (ret < 0)
 		return ret;
 
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, 0);
 	if (ret < 0)
 		return ret;
 
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		return ret;
 
@@ -704,7 +911,7 @@ static int ax88178_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88178_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   speed, ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL && data->ledmode)
 		marvell_led_status(dev, speed);
@@ -733,15 +940,15 @@ static void ax88178_set_mfb(struct usbnet *dev)
 		mfb = AX_RX_CTL_MFB_16384;
 	}
 
-	rxctl = asix_read_rx_ctl(dev);
-	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb);
+	rxctl = asix_read_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb, 0);
 
-	medium = asix_read_medium_status(dev);
+	medium = asix_read_medium_status(dev, 0);
 	if (dev->net->mtu > 1500)
 		medium |= AX_MEDIUM_JFE;
 	else
 		medium &= ~AX_MEDIUM_JFE;
-	asix_write_medium_mode(dev, medium);
+	asix_write_medium_mode(dev, medium, 0);
 
 	if (dev->rx_urb_size > old_rx_urb_size)
 		usbnet_unlink_rx_urbs(dev);
@@ -790,7 +997,7 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	usbnet_get_endpoints(dev,intf);
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret);
 		return ret;
@@ -811,10 +1018,10 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88178_ethtool_ops;
 
 	/* Blink LEDS so users know driver saw dongle */
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
 	/* Asix framing packs multiple eth frames into a 2K usb bulk transfer */
@@ -877,7 +1084,7 @@ static const struct driver_info ax88772_info = {
 	.unbind = ax88772_unbind,
 	.status = asix_status,
 	.link_reset = ax88772_link_reset,
-	.reset = ax88772_link_reset,
+	.reset = ax88772_reset,
 	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
@@ -1005,7 +1212,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Lenovo U2L100P 10/100
 	USB_DEVICE (0x17ef, 0x7203),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	// ASIX AX88772B 10/100
 	USB_DEVICE (0x0b95, 0x772b),
@@ -1073,7 +1280,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Asus USB Ethernet Adapter
 	USB_DEVICE (0x0b95, 0x7e2b),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	/* ASIX 88172a demo board */
 	USB_DEVICE(0x0b95, 0x172a),
@@ -1095,8 +1302,8 @@ static struct usb_driver asix_driver = {
 	.name =		DRIVER_NAME,
 	.id_table =	products,
 	.probe =	usbnet_probe,
-	.suspend =	usbnet_suspend,
-	.resume =	usbnet_resume,
+	.suspend =	asix_suspend,
+	.resume =	asix_resume,
 	.disconnect =	usbnet_disconnect,
 	.supports_autosuspend = 1,
 	.disable_hub_initiated_lpm = 1,
diff --git a/drivers/net/usb/ax88172a.c b/drivers/net/usb/ax88172a.c
index 163a2c5..49a3bc1 100644
--- a/drivers/net/usb/ax88172a.c
+++ b/drivers/net/usb/ax88172a.c
@@ -81,7 +81,7 @@ static void ax88172a_adjust_link(struct net_device *netdev)
 	}
 
 	if (mode != priv->oldmode) {
-		asix_write_medium_mode(dev, mode);
+		asix_write_medium_mode(dev, mode, 0);
 		priv->oldmode = mode;
 		netdev_dbg(netdev, "speed %u duplex %d, setting mode to 0x%04x\n",
 			   phydev->speed, phydev->duplex, mode);
@@ -176,18 +176,19 @@ static int ax88172a_reset_phy(struct usbnet *dev, int embd_phy)
 {
 	int ret;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
 
-	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD,
+			    0);
 	if (ret < 0)
 		goto err;
 
@@ -213,7 +214,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->driver_priv = priv;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read MAC address: %d\n", ret);
 		goto free;
@@ -224,7 +225,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88172a_ethtool_ops;
 
 	/* are we using the internal or the external phy? */
-	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf);
+	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read software interface selection register: %d\n",
 			   ret);
@@ -303,20 +304,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	ax88172a_reset_phy(dev, priv->use_embdphy);
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+	ret = asix_write_rx_ctl(dev, 0x0000, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
 
 	msleep(150);
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-			     AX88772_IPG2_DEFAULT, 0, NULL);
+			     AX88772_IPG2_DEFAULT, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -325,20 +326,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-			     data->mac_addr);
+			     data->mac_addr, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, 0);
 	netdev_dbg(dev->net, "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1471097

From	David Miller <davem@davemloft.net>
Date	2016-08-27 06:30 +0200
Message-ID	<saDpM-8jW-3@gated-at.bofh.it>
In reply to	#1470377

Networking patch series need to be submitted to netdev@vger.kernel.org

Thank you.

[toc] | [prev] | [next] | [standalone]

#1471840 — [PATCH v3 3/5] net: asix: Fix AX88772x resume failures

From	robert.foss@collabora.com
Date	2016-08-29 15:40 +0200
Subject	[PATCH v3 3/5] net: asix: Fix AX88772x resume failures
Message-ID	<sbuX7-7SV-1@gated-at.bofh.it>
In reply to	#1470377

From: Allan Chou <allan@asix.com.tw>

The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY

Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 47 +++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 46 insertions(+), 1 deletion(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index ebeb730..083dc2e 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -35,6 +35,15 @@
 
 #define	PHY_MODE_RTL8211CL	0x000C
 
+#define AX88772A_PHY14H		0x14
+#define AX88772A_PHY14H_DEFAULT 0x442C
+
+#define AX88772A_PHY15H		0x15
+#define AX88772A_PHY15H_DEFAULT 0x03C8
+
+#define AX88772A_PHY16H		0x16
+#define AX88772A_PHY16H_DEFAULT 0x4044
+
 struct ax88172_int_data {
 	__le16 res1;
 	u8 link;
@@ -424,7 +433,7 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
-	u16 rx_ctl;
+	u16 rx_ctl, phy14h, phy15h, phy16h;
 	u8 chipcode = 0;
 
 	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
@@ -482,6 +491,32 @@ static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
 				   ret);
 			goto out;
 		}
+	} else if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772A_CHIPCODE) {
+		/* Check if the PHY registers have default settings */
+		phy14h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H);
+		phy15h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H);
+		phy16h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H);
+
+		netdev_dbg(dev->net,
+			   "772a_hw_reset: MR20=0x%x MR21=0x%x MR22=0x%x\n",
+			   phy14h, phy15h, phy16h);
+
+		/* Restore PHY registers default setting if not */
+		if (phy14h != AX88772A_PHY14H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY14H,
+					     AX88772A_PHY14H_DEFAULT);
+		if (phy15h != AX88772A_PHY15H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY15H,
+					     AX88772A_PHY15H_DEFAULT);
+		if (phy16h != AX88772A_PHY16H_DEFAULT)
+			asix_mdio_write_nopm(dev->net, dev->mii.phy_id,
+					     AX88772A_PHY16H,
+					     AX88772A_PHY16H_DEFAULT);
 	}
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
@@ -543,6 +578,15 @@ static const struct net_device_ops ax88772_netdev_ops = {
 static void ax88772_suspend(struct usbnet *dev)
 {
 	struct asix_common_private *priv = dev->driver_priv;
+	u16 medium;
+
+	/* Stop MAC operation */
+	medium = asix_read_medium_status(dev, 0);
+	medium &= ~AX_MEDIUM_RE;
+	asix_write_medium_mode(dev, medium, 0);
+
+	netdev_dbg(dev->net, "ax88772_suspend: medium=0x%04x\n",
+		   asix_read_medium_status(dev, 0));
 
 	/* Preserve BMCR for restoring */
 	priv->presvd_phy_bmcr =
@@ -577,6 +621,7 @@ static void ax88772_restore_phy(struct usbnet *dev)
 		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
 				     priv->presvd_phy_bmcr);
 
+		mii_nway_restart(&dev->mii);
 		priv->presvd_phy_advertise = 0;
 		priv->presvd_phy_bmcr = 0;
 	}
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1471845 — [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

From	robert.foss@collabora.com
Date	2016-08-29 15:40 +0200
Subject	[PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg
Message-ID	<sbuX7-7SV-29@gated-at.bofh.it>
In reply to	#1470377

From: Grant Grundler <grundler@chromium.org>

The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.

The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.

Ignore the ret value since it's ignored in XXX_link_reset() functions.

Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_devices.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index dbcdda2..cce2495 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -928,12 +928,9 @@ static int ax88178_reset(struct usbnet *dev)
 	asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000,
 			ADVERTISE_1000FULL);
 
+	asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
-	if (ret < 0)
-		return ret;
-
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1471846 — [PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected

From	robert.foss@collabora.com
Date	2016-08-29 15:40 +0200
Subject	[PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected
Message-ID	<sbuX7-7SV-19@gated-at.bofh.it>
In reply to	#1470377

From: Vincent Palatin <vpalatin@chromium.org>

Check the answers from the USB stack and avoid re-sending multiple times
the request if the device has disappeared.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix_common.c  | 56 +++++++++++++++++++++++++++++++++---------
 drivers/net/usb/asix_devices.c |  2 ++
 2 files changed, 46 insertions(+), 12 deletions(-)

diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c
index 25609ee..f79eb12 100644
--- a/drivers/net/usb/asix_common.c
+++ b/drivers/net/usb/asix_common.c
@@ -428,13 +428,21 @@ int asix_mdio_read(struct net_device *netdev, int phy_id, int loc)
 	__le16 res;
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 0);
+		ret = asix_set_sw_mii(dev, 0);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
 
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
 				(__u16)loc, 2, &res, 0);
@@ -453,16 +461,24 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
 	__le16 res = cpu_to_le16(val);
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
 			phy_id, loc, val);
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 0);
+		ret = asix_set_sw_mii(dev, 0);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return;
+	}
 
 	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
 		       (__u16)loc, 2, &res, 0);
@@ -476,13 +492,21 @@ int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
 	__le16 res;
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 1);
+		ret = asix_set_sw_mii(dev, 1);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return ret;
+	}
 
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
 		      (__u16)loc, 2, &res, 1);
@@ -502,16 +526,24 @@ asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc, int val)
 	__le16 res = cpu_to_le16(val);
 	u8 smsr;
 	int i = 0;
+	int ret;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
 			phy_id, loc, val);
 
 	mutex_lock(&dev->phy_mutex);
 	do {
-		asix_set_sw_mii(dev, 1);
+		ret = asix_set_sw_mii(dev, 1);
+		if (ret == -ENODEV)
+			break;
 		usleep_range(1000, 1100);
-		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
-	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+		ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG,
+				    0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30) && (ret != -ENODEV));
+	if (ret == -ENODEV) {
+		mutex_unlock(&dev->phy_mutex);
+		return;
+	}
 
 	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
 		       (__u16)loc, 2, &res, 1);
diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index aaa4290..ebeb730 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -79,6 +79,8 @@ static u32 asix_get_phyid(struct usbnet *dev)
 	/* Poll for the rare case the FW or phy isn't ready yet.  */
 	for (i = 0; i < 100; i++) {
 		phy_reg = asix_mdio_read(dev->net, dev->mii.phy_id, MII_PHYSID1);
+		if (phy_reg < 0)
+			return 0;
 		if (phy_reg != 0 && phy_reg != 0xFFFF)
 			break;
 		mdelay(1);
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

#1471847 — [PATCH v3 1/5] net: asix: Add in_pm parameter

From	robert.foss@collabora.com
Date	2016-08-29 15:40 +0200
Subject	[PATCH v3 1/5] net: asix: Add in_pm parameter
Message-ID	<sbuX7-7SV-13@gated-at.bofh.it>
In reply to	#1470377

From: Freddy Xin <freddy@asix.com.tw>

In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.

Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.

Reset HW in resume function to ensure the PHY works correctly.

Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
---
 drivers/net/usb/asix.h         |  40 +++--
 drivers/net/usb/asix_common.c  | 180 +++++++++++++++-----
 drivers/net/usb/asix_devices.c | 373 ++++++++++++++++++++++++++++++++---------
 drivers/net/usb/ax88172a.c     |  29 ++--
 4 files changed, 472 insertions(+), 150 deletions(-)

diff --git a/drivers/net/usb/asix.h b/drivers/net/usb/asix.h
index a2d3ea6..d109242 100644
--- a/drivers/net/usb/asix.h
+++ b/drivers/net/usb/asix.h
@@ -46,6 +46,7 @@
 #define AX_CMD_SET_SW_MII		0x06
 #define AX_CMD_READ_MII_REG		0x07
 #define AX_CMD_WRITE_MII_REG		0x08
+#define AX_CMD_STATMNGSTS_REG		0x09
 #define AX_CMD_SET_HW_MII		0x0a
 #define AX_CMD_READ_EEPROM		0x0b
 #define AX_CMD_WRITE_EEPROM		0x0c
@@ -71,6 +72,17 @@
 #define AX_CMD_SW_RESET			0x20
 #define AX_CMD_SW_PHY_STATUS		0x21
 #define AX_CMD_SW_PHY_SELECT		0x22
+#define AX_QCTCTRL			0x2A
+
+#define AX_CHIPCODE_MASK		0x70
+#define AX_AX88772_CHIPCODE		0x00
+#define AX_AX88772A_CHIPCODE		0x10
+#define AX_AX88772B_CHIPCODE		0x20
+#define AX_HOST_EN			0x01
+
+#define AX_PHYSEL_PSEL			0x01
+#define AX_PHYSEL_SSMII			0
+#define AX_PHYSEL_SSEN			0x10
 
 #define AX_PHY_SELECT_MASK		(BIT(3) | BIT(2))
 #define AX_PHY_SELECT_INTERNAL		0
@@ -173,6 +185,10 @@ struct asix_rx_fixup_info {
 };
 
 struct asix_common_private {
+	void (*resume)(struct usbnet *dev);
+	void (*suspend)(struct usbnet *dev);
+	u16 presvd_phy_advertise;
+	u16 presvd_phy_bmcr;
 	struct asix_rx_fixup_info rx_fixup_info;
 };
 
@@ -182,10 +198,10 @@ extern const struct driver_info ax88172a_info;
 #define FLAG_EEPROM_MAC		(1UL << 0)  /* init device MAC from eeprom */
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data);
+		  u16 size, void *data, int in_pm);
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data);
+		   u16 size, void *data, int in_pm);
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value,
 			  u16 index, u16 size, void *data);
@@ -197,27 +213,31 @@ int asix_rx_fixup_common(struct usbnet *dev, struct sk_buff *skb);
 struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 			      gfp_t flags);
 
-int asix_set_sw_mii(struct usbnet *dev);
-int asix_set_hw_mii(struct usbnet *dev);
+int asix_set_sw_mii(struct usbnet *dev, int in_pm);
+int asix_set_hw_mii(struct usbnet *dev, int in_pm);
 
 int asix_read_phy_addr(struct usbnet *dev, int internal);
 int asix_get_phy_addr(struct usbnet *dev);
 
-int asix_sw_reset(struct usbnet *dev, u8 flags);
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm);
 
-u16 asix_read_rx_ctl(struct usbnet *dev);
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode);
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm);
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
 
-u16 asix_read_medium_status(struct usbnet *dev);
-int asix_write_medium_mode(struct usbnet *dev, u16 mode);
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep);
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
 
 void asix_set_multicast(struct net_device *net);
 
 int asix_mdio_read(struct net_device *netdev, int phy_id, int loc);
 void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val);
 
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc);
+void asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc,
+			  int val);
+
 void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo);
 
diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c
index 7de5ab5..25609ee 100644
--- a/drivers/net/usb/asix_common.c
+++ b/drivers/net/usb/asix_common.c
@@ -22,24 +22,49 @@
 #include "asix.h"
 
 int asix_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		  u16 size, void *data)
+		  u16 size, void *data, int in_pm)
 {
 	int ret;
-	ret = usbnet_read_cmd(dev, cmd,
-			       USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-			       value, index, data, size);
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_read_cmd;
+	else
+		fn = usbnet_read_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to read reg index 0x%04x: %d\n",
+			    index, ret);
 
-	if (ret != size && ret >= 0)
-		return -EINVAL;
 	return ret;
 }
 
 int asix_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
-		   u16 size, void *data)
+		   u16 size, void *data, int in_pm)
 {
-	return usbnet_write_cmd(dev, cmd,
-				USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
-				value, index, data, size);
+	int ret;
+	int (*fn)(struct usbnet *, u8, u8, u16, u16, const void *, u16);
+
+	BUG_ON(!dev);
+
+	if (!in_pm)
+		fn = usbnet_write_cmd;
+	else
+		fn = usbnet_write_cmd_nopm;
+
+	ret = fn(dev, cmd, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+		 value, index, data, size);
+
+	if (unlikely(ret < 0))
+		netdev_warn(dev->net, "Failed to write reg index 0x%04x: %d\n",
+			    index, ret);
+
+	return ret;
 }
 
 void asix_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value, u16 index,
@@ -225,19 +250,20 @@ struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
 	return skb;
 }
 
-int asix_set_sw_mii(struct usbnet *dev)
+int asix_set_sw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_SW_MII, 0x0000, 0, 0, NULL, in_pm);
+
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable software MII access\n");
 	return ret;
 }
 
-int asix_set_hw_mii(struct usbnet *dev)
+int asix_set_hw_mii(struct usbnet *dev, int in_pm)
 {
 	int ret;
-	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SET_HW_MII, 0x0000, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to enable hardware MII access\n");
 	return ret;
@@ -247,7 +273,7 @@ int asix_read_phy_addr(struct usbnet *dev, int internal)
 {
 	int offset = (internal ? 1 : 0);
 	u8 buf[2];
-	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf, 0);
 
 	netdev_dbg(dev->net, "asix_get_phy_addr()\n");
 
@@ -270,21 +296,21 @@ int asix_get_phy_addr(struct usbnet *dev)
 }
 
 
-int asix_sw_reset(struct usbnet *dev, u8 flags)
+int asix_sw_reset(struct usbnet *dev, u8 flags, int in_pm)
 {
 	int ret;
 
-        ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_RESET, flags, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to send software reset: %02x\n", ret);
 
 	return ret;
 }
 
-u16 asix_read_rx_ctl(struct usbnet *dev)
+u16 asix_read_rx_ctl(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_RX_CTL, 0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading RX_CTL register: %02x\n", ret);
@@ -295,12 +321,12 @@ out:
 	return ret;
 }
 
-int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
+int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_rx_ctl() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_RX_CTL, mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write RX_CTL mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -308,10 +334,11 @@ int asix_write_rx_ctl(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-u16 asix_read_medium_status(struct usbnet *dev)
+u16 asix_read_medium_status(struct usbnet *dev, int in_pm)
 {
 	__le16 v;
-	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS, 0, 0, 2, &v);
+	int ret = asix_read_cmd(dev, AX_CMD_READ_MEDIUM_STATUS,
+				0, 0, 2, &v, in_pm);
 
 	if (ret < 0) {
 		netdev_err(dev->net, "Error reading Medium Status register: %02x\n",
@@ -323,12 +350,13 @@ u16 asix_read_medium_status(struct usbnet *dev)
 
 }
 
-int asix_write_medium_mode(struct usbnet *dev, u16 mode)
+int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_medium_mode() - mode = 0x%04x\n", mode);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, mode, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE,
+			     mode, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write Medium Mode mode to 0x%04x: %02x\n",
 			   mode, ret);
@@ -336,12 +364,12 @@ int asix_write_medium_mode(struct usbnet *dev, u16 mode)
 	return ret;
 }
 
-int asix_write_gpio(struct usbnet *dev, u16 value, int sleep)
+int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
 {
 	int ret;
 
 	netdev_dbg(dev->net, "asix_write_gpio() - value = 0x%04x\n", value);
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, value, 0, 0, NULL, in_pm);
 	if (ret < 0)
 		netdev_err(dev->net, "Failed to write GPIO value 0x%04x: %02x\n",
 			   value, ret);
@@ -398,16 +426,23 @@ int asix_mdio_read(struct net_device *netdev, int phy_id, int loc)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res;
+	u8 smsr;
+	int i = 0;
 
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
+	do {
+		asix_set_sw_mii(dev, 0);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
 	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
-				(__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+				(__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
 	mutex_unlock(&dev->phy_mutex);
 
 	netdev_dbg(dev->net, "asix_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
-		   phy_id, loc, le16_to_cpu(res));
+			phy_id, loc, le16_to_cpu(res));
 
 	return le16_to_cpu(res);
 }
@@ -416,13 +451,71 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
 {
 	struct usbnet *dev = netdev_priv(netdev);
 	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
 
 	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
-		   phy_id, loc, val);
+			phy_id, loc, val);
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		asix_set_sw_mii(dev, 0);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 0);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 0);
+	asix_set_hw_mii(dev, 0);
+	mutex_unlock(&dev->phy_mutex);
+}
+
+int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res;
+	u8 smsr;
+	int i = 0;
+
+	mutex_lock(&dev->phy_mutex);
+	do {
+		asix_set_sw_mii(dev, 1);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id,
+		      (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
+	mutex_unlock(&dev->phy_mutex);
+
+	netdev_dbg(dev->net, "asix_mdio_read_nopm() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
+			phy_id, loc, le16_to_cpu(res));
+
+	return le16_to_cpu(res);
+}
+
+void
+asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc, int val)
+{
+	struct usbnet *dev = netdev_priv(netdev);
+	__le16 res = cpu_to_le16(val);
+	u8 smsr;
+	int i = 0;
+
+	netdev_dbg(dev->net, "asix_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
+			phy_id, loc, val);
+
 	mutex_lock(&dev->phy_mutex);
-	asix_set_sw_mii(dev);
-	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id, (__u16)loc, 2, &res);
-	asix_set_hw_mii(dev);
+	do {
+		asix_set_sw_mii(dev, 1);
+		usleep_range(1000, 1100);
+		asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &smsr, 1);
+	} while (!(smsr & AX_HOST_EN) && (i++ < 30));
+
+	asix_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id,
+		       (__u16)loc, 2, &res, 1);
+	asix_set_hw_mii(dev, 1);
 	mutex_unlock(&dev->phy_mutex);
 }
 
@@ -431,7 +524,8 @@ void asix_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 	struct usbnet *dev = netdev_priv(net);
 	u8 opt;
 
-	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE, 0, 0, 1, &opt) < 0) {
+	if (asix_read_cmd(dev, AX_CMD_READ_MONITOR_MODE,
+			  0, 0, 1, &opt, 0) < 0) {
 		wolinfo->supported = 0;
 		wolinfo->wolopts = 0;
 		return;
@@ -455,7 +549,7 @@ int asix_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo)
 		opt |= AX_MONITOR_MAGIC;
 
 	if (asix_write_cmd(dev, AX_CMD_WRITE_MONITOR_MODE,
-			      opt, 0, 0, NULL) < 0)
+			      opt, 0, 0, NULL, 0) < 0)
 		return -EINVAL;
 
 	return 0;
@@ -490,7 +584,7 @@ int asix_get_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	/* ax8817x returns 2 bytes from eeprom on read */
 	for (i = first_word; i <= last_word; i++) {
 		if (asix_read_cmd(dev, AX_CMD_READ_EEPROM, i, 0, 2,
-				  &(eeprom_buff[i - first_word])) < 0) {
+				  &eeprom_buff[i - first_word], 0) < 0) {
 			kfree(eeprom_buff);
 			return -EIO;
 		}
@@ -531,7 +625,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	   the EEPROM */
 	if (eeprom->offset & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, first_word, 0, 2,
-				    &(eeprom_buff[0]));
+				    &eeprom_buff[0], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", first_word);
 			goto free;
@@ -540,7 +634,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 
 	if ((eeprom->offset + eeprom->len) & 1) {
 		ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, last_word, 0, 2,
-				    &(eeprom_buff[last_word - first_word]));
+				    &eeprom_buff[last_word - first_word], 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to read EEPROM at offset 0x%02x.\n", last_word);
 			goto free;
@@ -550,7 +644,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 	memcpy((u8 *)eeprom_buff + (eeprom->offset & 1), data, eeprom->len);
 
 	/* write data to EEPROM */
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to enable EEPROM write\n");
 		goto free;
@@ -561,7 +655,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		netdev_dbg(net, "write to EEPROM at offset 0x%02x, data 0x%04x\n",
 			   i, eeprom_buff[i - first_word]);
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_EEPROM, i,
-				     eeprom_buff[i - first_word], 0, NULL);
+				     eeprom_buff[i - first_word], 0, NULL, 0);
 		if (ret < 0) {
 			netdev_err(net, "Failed to write EEPROM at offset 0x%02x.\n",
 				   i);
@@ -570,7 +664,7 @@ int asix_set_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom,
 		msleep(20);
 	}
 
-	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0x0000, 0, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(net, "Failed to disable EEPROM write\n");
 		goto free;
diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index 5cabefc..aaa4290 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -184,7 +184,7 @@ static int ax88172_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88172_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -213,18 +213,19 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 	/* Toggle the GPIOs in a manufacturer/model specific way */
 	for (i = 2; i >= 0; i--) {
 		ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS,
-				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL);
+				(gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL, 0);
 		if (ret < 0)
 			goto out;
 		msleep(5);
 	}
 
-	ret = asix_write_rx_ctl(dev, 0x80);
+	ret = asix_write_rx_ctl(dev, 0x80, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID,
+			    0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "read AX_CMD_READ_NODE_ID failed: %d\n",
 			   ret);
@@ -290,7 +291,7 @@ static int ax88772_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88772_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	return 0;
 }
@@ -298,78 +299,192 @@ static int ax88772_link_reset(struct usbnet *dev)
 static int ax88772_reset(struct usbnet *dev)
 {
 	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret;
+
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, 0);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
+	if (ret < 0)
+		goto out;
+
+	asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, 0);
+	if (ret < 0)
+		goto out;
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
 	int ret, embd_phy;
 	u16 rx_ctl;
 
-	ret = asix_write_gpio(dev,
-			AX_GPIO_RSE | AX_GPIO_GPO_2 | AX_GPIO_GPO2EN, 5);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_2 |
+			      AX_GPIO_GPO2EN, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	embd_phy = ((asix_get_phy_addr(dev) & 0x1f) == 0x10 ? 1 : 0);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy,
+			     0, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
 		goto out;
 	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL);
-	if (ret < 0)
-		goto out;
+	if (embd_phy) {
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD, in_pm);
+		if (ret < 0)
+			goto out;
 
-	msleep(150);
+		usleep_range(10000, 11000);
 
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
-	if (ret < 0)
-		goto out;
+		ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+		if (ret < 0)
+			goto out;
 
-	msleep(150);
+		msleep(60);
 
-	if (embd_phy) {
-		ret = asix_sw_reset(dev, AX_SWRESET_IPRL);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	} else {
-		ret = asix_sw_reset(dev, AX_SWRESET_PRTE);
+		ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL,
+				    in_pm);
 		if (ret < 0)
 			goto out;
 	}
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))){
+		ret = -EIO;
+		goto out;
+	}
+
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
-	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
+			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
+			     AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
+		goto out;
+	}
 
-	ret = asix_sw_reset(dev, AX_SWRESET_PRL);
+	/* Rewrite MAC address */
+	ether_addr_copy(data->mac_addr, dev->net->dev_addr);
+	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0,
+			     ETH_ALEN, data->mac_addr, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
+	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	rx_ctl = asix_read_medium_status(dev, in_pm);
+	netdev_dbg(dev->net,
+		   "Medium Status is 0x%04x after all initializations\n",
+		   rx_ctl);
+
+	return 0;
+
+out:
+	return ret;
+}
+
+static int ax88772a_hw_reset(struct usbnet *dev, int in_pm)
+{
+	struct asix_data *data = (struct asix_data *)&dev->data;
+	int ret, embd_phy;
+	u16 rx_ctl;
+	u8 chipcode = 0;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL);
+	ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm);
 	if (ret < 0)
 		goto out;
 
-	msleep(150);
+	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
 
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
-	asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
-			ADVERTISE_ALL | ADVERTISE_CSMA);
-	mii_nway_restart(&dev->mii);
+	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy |
+			     AX_PHYSEL_SSEN, 0, 0, NULL, in_pm);
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
+		goto out;
+	}
+	usleep_range(10000, 11000);
 
-	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_IPRL, in_pm);
 	if (ret < 0)
 		goto out;
 
+	usleep_range(10000, 11000);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(160);
+
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm);
+	if (ret < 0)
+		goto out;
+
+	ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm);
+	if (ret < 0)
+		goto out;
+
+	msleep(200);
+
+	if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id,
+					   MII_PHYSID1))) {
+		ret = -1;
+		goto out;
+	}
+
+	ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0,
+			    0, 1, &chipcode, in_pm);
+	if (ret < 0)
+		goto out;
+
+	if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772B_CHIPCODE) {
+		ret = asix_write_cmd(dev, AX_QCTCTRL, 0x8000, 0x8001,
+				     0, NULL, in_pm);
+		if (ret < 0) {
+			netdev_dbg(dev->net, "Write BQ setting failed: %d\n",
+				   ret);
+			goto out;
+		}
+	}
+
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 				AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-				AX88772_IPG2_DEFAULT, 0, NULL);
+				AX88772_IPG2_DEFAULT, 0, NULL, in_pm);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -378,20 +493,29 @@ static int ax88772_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, in_pm);
+	if (ret < 0)
+		goto out;
+
+	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
+	ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm);
+	if (ret < 0)
+		return ret;
+
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, in_pm);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, in_pm);
 	netdev_dbg(dev->net,
 		   "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
@@ -400,7 +524,6 @@ static int ax88772_reset(struct usbnet *dev)
 
 out:
 	return ret;
-
 }
 
 static const struct net_device_ops ax88772_netdev_ops = {
@@ -415,11 +538,87 @@ static const struct net_device_ops ax88772_netdev_ops = {
 	.ndo_set_rx_mode        = asix_set_multicast,
 };
 
+static void ax88772_suspend(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	/* Preserve BMCR for restoring */
+	priv->presvd_phy_bmcr =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_BMCR);
+
+	/* Preserve ANAR for restoring */
+	priv->presvd_phy_advertise =
+		asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE);
+}
+
+static int asix_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->suspend)
+		priv->suspend(dev);
+
+	return usbnet_suspend(intf, message);
+}
+
+static void ax88772_restore_phy(struct usbnet *dev)
+{
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->presvd_phy_advertise) {
+		/* Restore Advertisement control reg */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE,
+				     priv->presvd_phy_advertise);
+
+		/* Restore BMCR */
+		asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR,
+				     priv->presvd_phy_bmcr);
+
+		priv->presvd_phy_advertise = 0;
+		priv->presvd_phy_bmcr = 0;
+	}
+}
+
+static void ax88772_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++)
+		if (!ax88772_hw_reset(dev, 1))
+			break;
+	ax88772_restore_phy(dev);
+}
+
+static void ax88772a_resume(struct usbnet *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++) {
+		if (!ax88772a_hw_reset(dev, 1))
+			break;
+	}
+
+	ax88772_restore_phy(dev);
+}
+
+static int asix_resume(struct usb_interface *intf)
+{
+	struct usbnet *dev = usb_get_intfdata(intf);
+	struct asix_common_private *priv = dev->driver_priv;
+
+	if (priv->resume)
+		priv->resume(dev);
+
+	return usbnet_resume(intf);
+}
+
 static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 {
-	int ret, embd_phy, i;
-	u8 buf[ETH_ALEN];
+	int ret, i;
+	u8 buf[ETH_ALEN], chipcode = 0;
 	u32 phyid;
+	struct asix_common_private *priv;
 
 	usbnet_get_endpoints(dev,intf);
 
@@ -427,13 +626,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (dev->driver_info->data & FLAG_EEPROM_MAC) {
 		for (i = 0; i < (ETH_ALEN >> 1); i++) {
 			ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x04 + i,
-					0, 2, buf + i * 2);
+					    0, 2, buf + i * 2, 0);
 			if (ret < 0)
 				break;
 		}
 	} else {
 		ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID,
-				0, 0, ETH_ALEN, buf);
+				0, 0, ETH_ALEN, buf, 0);
 	}
 
 	if (ret < 0) {
@@ -456,16 +655,11 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
 	dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */
 
-	embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
+	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
+	chipcode &= AX_CHIPCODE_MASK;
 
-	/* Reset the PHY to normal operation mode */
-	ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
-	if (ret < 0) {
-		netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret);
-		return ret;
-	}
-
-	ax88772_reset(dev);
+	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+					    ax88772a_hw_reset(dev, 0);
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);
@@ -482,6 +676,18 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (!dev->driver_priv)
 		return -ENOMEM;
 
+	priv = dev->driver_priv;
+
+	priv->presvd_phy_bmcr = 0;
+	priv->presvd_phy_advertise = 0;
+	if (chipcode == AX_AX88772_CHIPCODE) {
+		priv->resume = ax88772_resume;
+		priv->suspend = ax88772_suspend;
+	} else {
+		priv->resume = ax88772a_resume;
+		priv->suspend = ax88772_suspend;
+	}
+
 	return 0;
 }
 
@@ -593,12 +799,12 @@ static int ax88178_reset(struct usbnet *dev)
 	int gpio0 = 0;
 	u32 phyid;
 
-	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status);
+	asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0);
 	netdev_dbg(dev->net, "GPIO Status: 0x%04x\n", status);
 
-	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL);
-	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom);
-	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL, 0);
+	asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0);
+	asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL, 0);
 
 	netdev_dbg(dev->net, "EEPROM index 0x17 is 0x%04x\n", eeprom);
 
@@ -614,15 +820,16 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "GPIO0: %d, PhyMode: %d\n", gpio0, data->phymode);
 
 	/* Power up external GigaPHY through AX88178 GPIO pin */
-	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 | AX_GPIO_GPO1EN, 40);
+	asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 |
+			AX_GPIO_GPO1EN, 40, 0);
 	if ((le16_to_cpu(eeprom) >> 8) != 1) {
-		asix_write_gpio(dev, 0x003c, 30);
-		asix_write_gpio(dev, 0x001c, 300);
-		asix_write_gpio(dev, 0x003c, 30);
+		asix_write_gpio(dev, 0x003c, 30, 0);
+		asix_write_gpio(dev, 0x001c, 300, 0);
+		asix_write_gpio(dev, 0x003c, 30, 0);
 	} else {
 		netdev_dbg(dev->net, "gpio phymode == 1 path\n");
-		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30);
-		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN, 30, 0);
+		asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30, 0);
 	}
 
 	/* Read PHYID register *AFTER* powering up PHY */
@@ -630,15 +837,15 @@ static int ax88178_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "PHYID=0x%08x\n", phyid);
 
 	/* Set AX88178 to enable MII/GMII/RGMII interface for external PHY */
-	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL);
+	asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL, 0);
 
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
-	asix_write_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, 0, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL) {
 		marvell_phy_init(dev);
@@ -655,18 +862,18 @@ static int ax88178_reset(struct usbnet *dev)
 
 	mii_nway_restart(&dev->mii);
 
-	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT);
+	ret = asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0);
 	if (ret < 0)
 		return ret;
 
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-							data->mac_addr);
+							data->mac_addr, 0);
 	if (ret < 0)
 		return ret;
 
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		return ret;
 
@@ -704,7 +911,7 @@ static int ax88178_link_reset(struct usbnet *dev)
 	netdev_dbg(dev->net, "ax88178_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
 		   speed, ecmd.duplex, mode);
 
-	asix_write_medium_mode(dev, mode);
+	asix_write_medium_mode(dev, mode, 0);
 
 	if (data->phymode == PHY_MODE_MARVELL && data->ledmode)
 		marvell_led_status(dev, speed);
@@ -733,15 +940,15 @@ static void ax88178_set_mfb(struct usbnet *dev)
 		mfb = AX_RX_CTL_MFB_16384;
 	}
 
-	rxctl = asix_read_rx_ctl(dev);
-	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb);
+	rxctl = asix_read_rx_ctl(dev, 0);
+	asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb, 0);
 
-	medium = asix_read_medium_status(dev);
+	medium = asix_read_medium_status(dev, 0);
 	if (dev->net->mtu > 1500)
 		medium |= AX_MEDIUM_JFE;
 	else
 		medium &= ~AX_MEDIUM_JFE;
-	asix_write_medium_mode(dev, medium);
+	asix_write_medium_mode(dev, medium, 0);
 
 	if (dev->rx_urb_size > old_rx_urb_size)
 		usbnet_unlink_rx_urbs(dev);
@@ -790,7 +997,7 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	usbnet_get_endpoints(dev,intf);
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret);
 		return ret;
@@ -811,10 +1018,10 @@ static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88178_ethtool_ops;
 
 	/* Blink LEDS so users know driver saw dongle */
-	asix_sw_reset(dev, 0);
+	asix_sw_reset(dev, 0, 0);
 	msleep(150);
 
-	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD);
+	asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0);
 	msleep(150);
 
 	/* Asix framing packs multiple eth frames into a 2K usb bulk transfer */
@@ -877,7 +1084,7 @@ static const struct driver_info ax88772_info = {
 	.unbind = ax88772_unbind,
 	.status = asix_status,
 	.link_reset = ax88772_link_reset,
-	.reset = ax88772_link_reset,
+	.reset = ax88772_reset,
 	.flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
 	.rx_fixup = asix_rx_fixup_common,
 	.tx_fixup = asix_tx_fixup,
@@ -1005,7 +1212,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Lenovo U2L100P 10/100
 	USB_DEVICE (0x17ef, 0x7203),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	// ASIX AX88772B 10/100
 	USB_DEVICE (0x0b95, 0x772b),
@@ -1073,7 +1280,7 @@ static const struct usb_device_id	products [] = {
 }, {
 	// Asus USB Ethernet Adapter
 	USB_DEVICE (0x0b95, 0x7e2b),
-	.driver_info = (unsigned long) &ax88772_info,
+	.driver_info = (unsigned long)&ax88772b_info,
 }, {
 	/* ASIX 88172a demo board */
 	USB_DEVICE(0x0b95, 0x172a),
@@ -1095,8 +1302,8 @@ static struct usb_driver asix_driver = {
 	.name =		DRIVER_NAME,
 	.id_table =	products,
 	.probe =	usbnet_probe,
-	.suspend =	usbnet_suspend,
-	.resume =	usbnet_resume,
+	.suspend =	asix_suspend,
+	.resume =	asix_resume,
 	.disconnect =	usbnet_disconnect,
 	.supports_autosuspend = 1,
 	.disable_hub_initiated_lpm = 1,
diff --git a/drivers/net/usb/ax88172a.c b/drivers/net/usb/ax88172a.c
index 163a2c5..49a3bc1 100644
--- a/drivers/net/usb/ax88172a.c
+++ b/drivers/net/usb/ax88172a.c
@@ -81,7 +81,7 @@ static void ax88172a_adjust_link(struct net_device *netdev)
 	}
 
 	if (mode != priv->oldmode) {
-		asix_write_medium_mode(dev, mode);
+		asix_write_medium_mode(dev, mode, 0);
 		priv->oldmode = mode;
 		netdev_dbg(netdev, "speed %u duplex %d, setting mode to 0x%04x\n",
 			   phydev->speed, phydev->duplex, mode);
@@ -176,18 +176,19 @@ static int ax88172a_reset_phy(struct usbnet *dev, int embd_phy)
 {
 	int ret;
 
-	ret = asix_sw_reset(dev, AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, AX_SWRESET_IPPD, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
-	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+	ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, 0);
 	if (ret < 0)
 		goto err;
 
 	msleep(150);
 
-	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD);
+	ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD,
+			    0);
 	if (ret < 0)
 		goto err;
 
@@ -213,7 +214,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->driver_priv = priv;
 
 	/* Get the MAC address */
-	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+	ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read MAC address: %d\n", ret);
 		goto free;
@@ -224,7 +225,7 @@ static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
 	dev->net->ethtool_ops = &ax88172a_ethtool_ops;
 
 	/* are we using the internal or the external phy? */
-	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf);
+	ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Failed to read software interface selection register: %d\n",
 			   ret);
@@ -303,20 +304,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	ax88172a_reset_phy(dev, priv->use_embdphy);
 
 	msleep(150);
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
-	ret = asix_write_rx_ctl(dev, 0x0000);
+	ret = asix_write_rx_ctl(dev, 0x0000, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
 
 	msleep(150);
 
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
 			     AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
-			     AX88772_IPG2_DEFAULT, 0, NULL);
+			     AX88772_IPG2_DEFAULT, 0, NULL, 0);
 	if (ret < 0) {
 		netdev_err(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
 		goto out;
@@ -325,20 +326,20 @@ static int ax88172a_reset(struct usbnet *dev)
 	/* Rewrite MAC address */
 	memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
 	ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
-			     data->mac_addr);
+			     data->mac_addr, 0);
 	if (ret < 0)
 		goto out;
 
 	/* Set RX_CTL to default values with 2k buffer, and enable cactus */
-	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+	ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0);
 	if (ret < 0)
 		goto out;
 
-	rx_ctl = asix_read_rx_ctl(dev);
+	rx_ctl = asix_read_rx_ctl(dev, 0);
 	netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-	rx_ctl = asix_read_medium_status(dev);
+	rx_ctl = asix_read_medium_status(dev, 0);
 	netdev_dbg(dev->net, "Medium Status is 0x%04x after all initializations\n",
 		   rx_ctl);
 
-- 
2.7.4

[toc] | [prev] | [next] | [standalone]

Page 1 of 2 [1] 2 Next page →

csiph-web

[PATCH v3 0/5] net/usb: asix driver improvements

Contents

#1470377 — [PATCH v3 0/5] net/usb: asix driver improvements

#1470379 — [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset

#1470380 — [PATCH v3 4/5] net: asix: see 802.3 spec for phy reset

#1470382 — [PATCH v3 3/5] net: asix: Fix AX88772x resume failures

#1470383 — [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1470385 — [PATCH v3 1/5] net: asix: Add in_pm parameter

#1470387 — [PATCH v3 3/5] net: asix: Fix AX88772x resume failures

#1470388 — [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1474564 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1474576 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1477616 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1477834 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1474565 — Re: [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1470389 — [PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected

#1470391 — [PATCH v3 1/5] net: asix: Add in_pm parameter

#1471097

#1471840 — [PATCH v3 3/5] net: asix: Fix AX88772x resume failures

#1471845 — [PATCH v3 5/5] net: asix: autoneg will set WRITE_MEDIUM reg

#1471846 — [PATCH v3 2/5] net: asix: Avoid looping when the device is disconnected

#1471847 — [PATCH v3 1/5] net: asix: Add in_pm parameter