Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1548096 > unrolled thread

[PATCH v6 00/25] Support qcom's HSIC USB and rewrite USB2 HS support

Back to article view | Back to linux.kernel

Contents

  [PATCH v6 00/25] Support qcom's HSIC USB and rewrite USB2 HS support Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 01/25] of: device: Support loading a module with OF based modalias Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 03/25] usb: ulpi: Support device discovery via DT Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 07/25] usb: chipidea: Notify events when switching host mode Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 15/25] usb: chipidea: msm: Add proper clk and reset support Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 08/25] usb: chipidea: Remove locking in ci_udc_start() Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 14/25] usb: chipidea: msm: Use hw_write_id_reg() instead of writel Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 04/25] usb: chipidea: Only read/write OTGSC from one place Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 06/25] usb: chipidea: Add platform flag for wrapper phy management Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 13/25] usb: chipidea: msm: Rely on core to override AHBBURST Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 10/25] usb: chipidea: Consolidate extcon notifiers Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 05/25] usb: chipidea: Handle extcon events properly Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 11/25] usb: chipidea: vbus event may exist before starting gadget Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
      Re: [PATCH v6 11/25] usb: chipidea: vbus event may exist before  starting gadget Peter Chen <hzpeterchen@gmail.com> - 2017-01-03 09:10 +0100
        Re: [PATCH v6 11/25] usb: chipidea: vbus event may exist before  starting gadget Peter Chen <hzpeterchen@gmail.com> - 2017-01-12 11:00 +0100
    [PATCH v6 02/25] of: device: Export of_device_{get_modalias,uvent_modalias} to modules Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100
    [PATCH v6 16/25] usb: chipidea: msm: Mux over secondary phy at the right time Stephen Boyd <stephen.boyd@linaro.org> - 2016-12-29 00:10 +0100

#1548096 — [PATCH v6 00/25] Support qcom's HSIC USB and rewrite USB2 HS support

The state of USB ChipIdea support on Qualcomm's platforms is not great.
The DT description of these devices requires up to three different nodes
for what amounts to be the same hardware block, when there should really
only be one. Furthermore, the "phy" driver that is in mainline (phy-msm-usb.c)
duplicates the OTG state machine and touches the ci controller wrapper
registers when it should really be focused on the phy and the ULPI accesses
needed to get the phy working. There's also a slimmed down phy driver for
the msm8916 platform, but really the phy hardware is the same as other MSMs,
so we have two drivers doing pretty much the same thing. This leads to a
situtaion where we have the chipidea core driver, the "phy" driver, and
sometimes the ehci-msm.c driver operating the same device all at the same
time with very little coordination. This just isn't very safe and is
confusing from a driver perspective when trying to figure out who does what.
Finally, there isn't any HSIC support on platforms like apq8074 so we
should add that.

This patch series updates the ChipIdea driver and the MSM wrapper
(ci_hdrc_msm.c) to properly handle the PHY and wrapper bits at the right
times in the right places. To get there, we update the ChipIdea core to
have support for the ULPI phy bus introduced by Heikki. Along the way
we fix bugs with the extcon handling for peripheral and OTG mode controllers
and move the parts of phy-usb-msm.c that are touching the CI controller
wrapper into the wrapper driver (ci_hdrc_msm.c). Finally we add support
for the HSIC phy based on the ULPI bus and rewrite the HS phy driver
(phy-usb-msm.c) as a standard ULPI phy driver.

Once this series is accepted, we should be able to delete the phy-usb-msm.c,
phy-qcom-8x16-usb.c, and ehci-msm.c drivers from the tree and use the ULPI
based phy driver (which also lives in drivers/phy/ instead of drivers/usb/phy/)
and the chipidea host core instead.

I've also sent separate patches for other minor pieces to make this
all work. The full tree can be found here[1], hacks and all to get
things working. I've tested this on the db410c, apq8074 dragonboard,
and ifc6410 with configfs gadgets and otg cables.

Patches based on v4.10-rc1

Changes from v5:
 * Replaced "Emulate OTGSC interrupt enable path" patch with a patch
   from Peter
 * Updated HS phy driver to support set_mode callback to handle pullup
 * New patch to set the mode to device or host in chipidea udc pullup
   function to toggle the pullup for HS mode
 * New patch to drop lock around event_notify callback to avoid lockdep
   issues
 * Removal of extcon usage from HS phy driver
 * Picked up acks from Heikki and Peter on ULPI core patch

Changes from v4:
 * Picked up Acks from Rob
 * Updated HS phy init sequence DT property to restrict it to offsets

Changes from v3:
 * Picked up Acks from Peter
 * Updated extcon consolidation patch per Peter's comments
 * Folded in simplification from Heikki for ULPI DT matching

Changes from v2:
 * Added SoC specific compatibles in phy bindings
 * Dropped AVVIS patch for OTG statemachine
 * New patch to consolidate extcon handlers
 * Picked up Acks from Peter
 * Rebased onto v4.8-rc1
 * Reworked ULPI OF code to look at vid == 0 instead of pid == 0
 * Dropped ULPI bindings for vid and pid overrides

Changes from v1:
 * Reworked ULPI device probing to keep using vendor/product ids that
   come from DT if needed and falls back to OF style match when product id
   is 0
 * PHY init later patch was rejected so that moved to a quirk flag and
   the msm wrapper started managing the phy on/off
 * Updated clk requirements for HSIC phy in binding doc
 * Added optional clk in wrapper for "housekeeping" found on older qcom
   platforms
 * Bug fix to OTGSC polling function
 * Changed runtime PM patch to set as active instead of get/put

TODO:
 * DMA fails on arm64 so we need something like [2] to make it work.
 * The db410c needs a driver to toggle the onboard switch to connect
   the usb hub instead of micro port when the usb cable is disconnected.
   I've sent a patch set for this[3], which needs some further
   discussion/development.
 * apq8064 platforms need a vbus regulator to really use otg and I haven't
   tried out the RPM based regulators yet
 * The HSIC phy on the apq8074 dragonboard is connected to a usb4604
   device which requires the i2c driver to probe and send an i2c
   sequence before the HSIC controller enumerates or HSIC doesn't work.
   Right now I have a hack to force the controller to probe defer
   once so that usb4604 probes first. This needs a more proper solution
   like having the DT describe a linkage between the controller and
   the usb device so we can enforce probe ordering.

[1] https://git.linaro.org/people/stephen.boyd/linux.git/log/?h=usb-hsic-8074
[2] https://patchwork.kernel.org/patch/9319527/
[3] https://lkml.kernel.org/r/20160914014246.31847-1-stephen.boyd@linaro.org

Peter Chen (1):
  usb: chipidea: vbus event may exist before starting gadget

Stephen Boyd (24):
  of: device: Support loading a module with OF based modalias
  of: device: Export of_device_{get_modalias,uvent_modalias} to modules
  usb: ulpi: Support device discovery via DT
  usb: chipidea: Only read/write OTGSC from one place
  usb: chipidea: Handle extcon events properly
  usb: chipidea: Add platform flag for wrapper phy management
  usb: chipidea: Notify events when switching host mode
  usb: chipidea: Remove locking in ci_udc_start()
  usb: chipidea: Add support for ULPI PHY bus
  usb: chipidea: Consolidate extcon notifiers
  usb: chipidea: msm: Mark device as runtime pm active
  usb: chipidea: msm: Rely on core to override AHBBURST
  usb: chipidea: msm: Use hw_write_id_reg() instead of writel
  usb: chipidea: msm: Add proper clk and reset support
  usb: chipidea: msm: Mux over secondary phy at the right time
  usb: chipidea: msm: Restore wrapper settings after reset
  usb: chipidea: msm: Make platform data driver local instead of global
  usb: chipidea: msm: Add reset controller for PHY POR bit
  usb: chipidea: msm: Handle phy power states
  usb: chipidea: msm: Be silent on probe defer errors
  usb: chipidea: Drop lock across event_notify during gadget stop
  usb: chipidea: Pullup D+ in device mode via phy APIs
  phy: Add support for Qualcomm's USB HSIC phy
  phy: Add support for Qualcomm's USB HS phy

 .../devicetree/bindings/phy/qcom,usb-hs-phy.txt    |  78 ++++++
 .../devicetree/bindings/phy/qcom,usb-hsic-phy.txt  |  65 +++++
 Documentation/devicetree/bindings/usb/ulpi.txt     |  20 ++
 drivers/of/device.c                                |  25 ++
 drivers/phy/Kconfig                                |  15 ++
 drivers/phy/Makefile                               |   2 +
 drivers/phy/phy-qcom-usb-hs.c                      | 243 ++++++++++++++++++
 drivers/phy/phy-qcom-usb-hsic.c                    | 160 ++++++++++++
 drivers/usb/chipidea/Kconfig                       |   8 +
 drivers/usb/chipidea/Makefile                      |   1 +
 drivers/usb/chipidea/ci.h                          |  22 +-
 drivers/usb/chipidea/ci_hdrc_msm.c                 | 280 ++++++++++++++++++---
 drivers/usb/chipidea/core.c                        | 126 ++++------
 drivers/usb/chipidea/host.c                        |  10 +
 drivers/usb/chipidea/otg.c                         |  96 +++++--
 drivers/usb/chipidea/udc.c                         |  17 +-
 drivers/usb/chipidea/ulpi.c                        | 113 +++++++++
 drivers/usb/common/ulpi.c                          |  79 +++++-
 include/linux/of_device.h                          |   6 +
 include/linux/usb/chipidea.h                       |   9 +-
 20 files changed, 1227 insertions(+), 148 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
 create mode 100644 Documentation/devicetree/bindings/usb/ulpi.txt
 create mode 100644 drivers/phy/phy-qcom-usb-hs.c
 create mode 100644 drivers/phy/phy-qcom-usb-hsic.c
 create mode 100644 drivers/usb/chipidea/ulpi.c

-- 
2.10.0.297.gf6727b0

[toc] | [next] | [standalone]

#1548097 — [PATCH v6 01/25] of: device: Support loading a module with OF based modalias

In the case of ULPI devices, we want to be able to load the
driver before registering the device so that we don't get stuck
in a loop waiting for the phy module to appear and failing usb
controller probe. Currently we request the ulpi module via the
ulpi ids, but in the DT case we might need to request it with the
OF based modalias instead. Add a common function that allows
anyone to request a module with the OF based modalias.

Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/of/device.c       | 23 +++++++++++++++++++++++
 include/linux/of_device.h |  6 ++++++
 2 files changed, 29 insertions(+)

diff --git a/drivers/of/device.c b/drivers/of/device.c
index fd5cfad7c403..8a22a253a830 100644
--- a/drivers/of/device.c
+++ b/drivers/of/device.c
@@ -226,6 +226,29 @@ ssize_t of_device_get_modalias(struct device *dev, char *str, ssize_t len)
 	return tsize;
 }
 
+int of_device_request_module(struct device *dev)
+{
+	char *str;
+	ssize_t size;
+	int ret;
+
+	size = of_device_get_modalias(dev, NULL, 0);
+	if (size < 0)
+		return size;
+
+	str = kmalloc(size + 1, GFP_KERNEL);
+	if (!str)
+		return -ENOMEM;
+
+	of_device_get_modalias(dev, str, size);
+	str[size] = '\0';
+	ret = request_module(str);
+	kfree(str);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(of_device_request_module);
+
 /**
  * of_device_uevent - Display OF related uevent information
  */
diff --git a/include/linux/of_device.h b/include/linux/of_device.h
index cc7dd687a89d..e9afbcc8de12 100644
--- a/include/linux/of_device.h
+++ b/include/linux/of_device.h
@@ -37,6 +37,7 @@ extern const void *of_device_get_match_data(const struct device *dev);
 
 extern ssize_t of_device_get_modalias(struct device *dev,
 					char *str, ssize_t len);
+extern int of_device_request_module(struct device *dev);
 
 extern void of_device_uevent(struct device *dev, struct kobj_uevent_env *env);
 extern int of_device_uevent_modalias(struct device *dev, struct kobj_uevent_env *env);
@@ -78,6 +79,11 @@ static inline int of_device_get_modalias(struct device *dev,
 	return -ENODEV;
 }
 
+static inline int of_device_request_module(struct device *dev)
+{
+	return -ENODEV;
+}
+
 static inline int of_device_uevent_modalias(struct device *dev,
 				   struct kobj_uevent_env *env)
 {
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548098 — [PATCH v6 03/25] usb: ulpi: Support device discovery via DT

The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.

The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.

The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.

If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 Documentation/devicetree/bindings/usb/ulpi.txt | 20 +++++++
 drivers/usb/common/ulpi.c                      | 79 ++++++++++++++++++++++++--
 2 files changed, 93 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/ulpi.txt

diff --git a/Documentation/devicetree/bindings/usb/ulpi.txt b/Documentation/devicetree/bindings/usb/ulpi.txt
new file mode 100644
index 000000000000..ca179dc4bd50
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ulpi.txt
@@ -0,0 +1,20 @@
+ULPI bus binding
+----------------
+
+Phys that are behind a ULPI connection can be described with the following
+binding. The host controller shall have a "ulpi" named node as a child, and
+that node shall have one enabled node underneath it representing the ulpi
+device on the bus.
+
+EXAMPLE
+-------
+
+usb {
+	compatible = "vendor,usb-controller";
+
+	ulpi {
+		phy {
+			compatible = "vendor,phy";
+		};
+	};
+};
diff --git a/drivers/usb/common/ulpi.c b/drivers/usb/common/ulpi.c
index 8b317702d761..c9480d77810c 100644
--- a/drivers/usb/common/ulpi.c
+++ b/drivers/usb/common/ulpi.c
@@ -16,6 +16,9 @@
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/clk/clk-conf.h>
 
 /* -------------------------------------------------------------------------- */
 
@@ -39,6 +42,10 @@ static int ulpi_match(struct device *dev, struct device_driver *driver)
 	struct ulpi *ulpi = to_ulpi_dev(dev);
 	const struct ulpi_device_id *id;
 
+	/* Some ULPI devices don't have a vendor id so rely on OF match */
+	if (ulpi->id.vendor == 0)
+		return of_driver_match_device(dev, driver);
+
 	for (id = drv->id_table; id->vendor; id++)
 		if (id->vendor == ulpi->id.vendor &&
 		    id->product == ulpi->id.product)
@@ -50,6 +57,11 @@ static int ulpi_match(struct device *dev, struct device_driver *driver)
 static int ulpi_uevent(struct device *dev, struct kobj_uevent_env *env)
 {
 	struct ulpi *ulpi = to_ulpi_dev(dev);
+	int ret;
+
+	ret = of_device_uevent_modalias(dev, env);
+	if (ret != -ENODEV)
+		return ret;
 
 	if (add_uevent_var(env, "MODALIAS=ulpi:v%04xp%04x",
 			   ulpi->id.vendor, ulpi->id.product))
@@ -60,6 +72,11 @@ static int ulpi_uevent(struct device *dev, struct kobj_uevent_env *env)
 static int ulpi_probe(struct device *dev)
 {
 	struct ulpi_driver *drv = to_ulpi_driver(dev->driver);
+	int ret;
+
+	ret = of_clk_set_defaults(dev->of_node, false);
+	if (ret < 0)
+		return ret;
 
 	return drv->probe(to_ulpi_dev(dev));
 }
@@ -87,8 +104,13 @@ static struct bus_type ulpi_bus = {
 static ssize_t modalias_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
 {
+	int len;
 	struct ulpi *ulpi = to_ulpi_dev(dev);
 
+	len = of_device_get_modalias(dev, buf, PAGE_SIZE - 1);
+	if (len != -ENODEV)
+		return len;
+
 	return sprintf(buf, "ulpi:v%04xp%04x\n",
 		       ulpi->id.vendor, ulpi->id.product);
 }
@@ -153,23 +175,45 @@ EXPORT_SYMBOL_GPL(ulpi_unregister_driver);
 
 /* -------------------------------------------------------------------------- */
 
-static int ulpi_register(struct device *dev, struct ulpi *ulpi)
+static int ulpi_of_register(struct ulpi *ulpi)
 {
-	int ret;
+	struct device_node *np = NULL, *child;
+	struct device *parent;
+
+	/* Find a ulpi bus underneath the parent or the grandparent */
+	parent = ulpi->dev.parent;
+	if (parent->of_node)
+		np = of_find_node_by_name(parent->of_node, "ulpi");
+	else if (parent->parent && parent->parent->of_node)
+		np = of_find_node_by_name(parent->parent->of_node, "ulpi");
+	if (!np)
+		return 0;
+
+	child = of_get_next_available_child(np, NULL);
+	of_node_put(np);
+	if (!child)
+		return -EINVAL;
 
-	ulpi->dev.parent = dev; /* needed early for ops */
+	ulpi->dev.of_node = child;
+
+	return 0;
+}
+
+static int ulpi_read_id(struct ulpi *ulpi)
+{
+	int ret;
 
 	/* Test the interface */
 	ret = ulpi_write(ulpi, ULPI_SCRATCH, 0xaa);
 	if (ret < 0)
-		return ret;
+		goto err;
 
 	ret = ulpi_read(ulpi, ULPI_SCRATCH);
 	if (ret < 0)
 		return ret;
 
 	if (ret != 0xaa)
-		return -ENODEV;
+		goto err;
 
 	ulpi->id.vendor = ulpi_read(ulpi, ULPI_VENDOR_ID_LOW);
 	ulpi->id.vendor |= ulpi_read(ulpi, ULPI_VENDOR_ID_HIGH) << 8;
@@ -177,13 +221,35 @@ static int ulpi_register(struct device *dev, struct ulpi *ulpi)
 	ulpi->id.product = ulpi_read(ulpi, ULPI_PRODUCT_ID_LOW);
 	ulpi->id.product |= ulpi_read(ulpi, ULPI_PRODUCT_ID_HIGH) << 8;
 
+	/* Some ULPI devices don't have a vendor id so rely on OF match */
+	if (ulpi->id.vendor == 0)
+		goto err;
+
+	request_module("ulpi:v%04xp%04x", ulpi->id.vendor, ulpi->id.product);
+	return 0;
+err:
+	of_device_request_module(&ulpi->dev);
+	return 0;
+}
+
+static int ulpi_register(struct device *dev, struct ulpi *ulpi)
+{
+	int ret;
+
+	ulpi->dev.parent = dev; /* needed early for ops */
 	ulpi->dev.bus = &ulpi_bus;
 	ulpi->dev.type = &ulpi_dev_type;
 	dev_set_name(&ulpi->dev, "%s.ulpi", dev_name(dev));
 
 	ACPI_COMPANION_SET(&ulpi->dev, ACPI_COMPANION(dev));
 
-	request_module("ulpi:v%04xp%04x", ulpi->id.vendor, ulpi->id.product);
+	ret = ulpi_of_register(ulpi);
+	if (ret)
+		return ret;
+
+	ret = ulpi_read_id(ulpi);
+	if (ret)
+		return ret;
 
 	ret = device_register(&ulpi->dev);
 	if (ret)
@@ -234,6 +300,7 @@ EXPORT_SYMBOL_GPL(ulpi_register_interface);
  */
 void ulpi_unregister_interface(struct ulpi *ulpi)
 {
+	of_node_put(ulpi->dev.of_node);
 	device_unregister(&ulpi->dev);
 }
 EXPORT_SYMBOL_GPL(ulpi_unregister_interface);
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548099 — [PATCH v6 07/25] usb: chipidea: Notify events when switching host mode

The chipidea/udc.c file sends a CI_HDRC_CONTROLLER_RESET_EVENT to
the wrapper drivers when it calls hw_device_reset(), but that
function is not called from chipidea/host.c. And the udc.c file
sends the CI_HDRC_CONTROLLER_STOPPED_EVENT but the host.c file
doesn't do anything.

The intent of the reset event is to allow the wrapper driver to
do any wrapper specific things after the reset bit has been set
in the usb command register. Therefore, add this event hook in
the host role after we toggle that bit.

Similarly, the intent of the stopped event is to allow the
wrapper driver to do any wrapper specific things after the device
is stopped. So when we stop the host role, send the stopped
event.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/host.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index 111b0e0b8698..f884c0877bca 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -90,6 +90,9 @@ static int ehci_ci_reset(struct usb_hcd *hcd)
 
 	ehci->need_io_watchdog = 0;
 
+	if (ci->platdata->notify_event)
+		ci->platdata->notify_event(ci, CI_HDRC_CONTROLLER_RESET_EVENT);
+
 	ci_platform_configure(ci);
 
 	return ret;
@@ -187,6 +190,9 @@ static void host_stop(struct ci_hdrc *ci)
 	struct usb_hcd *hcd = ci->hcd;
 
 	if (hcd) {
+		if (ci->platdata->notify_event)
+			ci->platdata->notify_event(ci,
+				CI_HDRC_CONTROLLER_STOPPED_EVENT);
 		usb_remove_hcd(hcd);
 		ci->role = CI_ROLE_END;
 		synchronize_irq(ci->irq);
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548100 — [PATCH v6 15/25] usb: chipidea: msm: Add proper clk and reset support

The msm chipidea controller uses two main clks, an AHB clk to
read/write the MMIO registers and a core clk called the system
clk that drives the controller itself. Add support for these clks
as they're required in all designs.

Also add support for an optional third clk that we need to turn
on to reset the controller and wrapper logic and other
"housekeeping" things. This clk was removed in later revisions of
the hardware because the reset methodology no longer required
clks to be enabled to propagate resets.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/ci_hdrc_msm.c | 72 +++++++++++++++++++++++++++++++++++---
 1 file changed, 68 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
index b282a717bf8c..7e870a253f55 100644
--- a/drivers/usb/chipidea/ci_hdrc_msm.c
+++ b/drivers/usb/chipidea/ci_hdrc_msm.c
@@ -10,11 +10,20 @@
 #include <linux/pm_runtime.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/chipidea.h>
+#include <linux/clk.h>
+#include <linux/reset.h>
 
 #include "ci.h"
 
 #define HS_PHY_AHB_MODE			0x0098
 
+struct ci_hdrc_msm {
+	struct platform_device *ci;
+	struct clk *core_clk;
+	struct clk *iface_clk;
+	struct clk *fs_clk;
+};
+
 static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
 {
 	struct device *dev = ci->gadget.dev.parent;
@@ -52,11 +61,20 @@ static struct ci_hdrc_platform_data ci_hdrc_msm_platdata = {
 
 static int ci_hdrc_msm_probe(struct platform_device *pdev)
 {
+	struct ci_hdrc_msm *ci;
 	struct platform_device *plat_ci;
 	struct usb_phy *phy;
+	struct clk *clk;
+	struct reset_control *reset;
+	int ret;
 
 	dev_dbg(&pdev->dev, "ci_hdrc_msm_probe\n");
 
+	ci = devm_kzalloc(&pdev->dev, sizeof(*ci), GFP_KERNEL);
+	if (!ci)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, ci);
+
 	/*
 	 * OTG(PHY) driver takes care of PHY initialization, clock management,
 	 * powering up VBUS, mapping of registers address space and power
@@ -68,29 +86,75 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
 
 	ci_hdrc_msm_platdata.usb_phy = phy;
 
+	reset = devm_reset_control_get(&pdev->dev, "core");
+	if (IS_ERR(reset))
+		return PTR_ERR(reset);
+
+	ci->core_clk = clk = devm_clk_get(&pdev->dev, "core");
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ci->iface_clk = clk = devm_clk_get(&pdev->dev, "iface");
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ci->fs_clk = clk = devm_clk_get(&pdev->dev, "fs");
+	if (IS_ERR(clk)) {
+		if (PTR_ERR(clk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		ci->fs_clk = NULL;
+	}
+
+	ret = clk_prepare_enable(ci->fs_clk);
+	if (ret)
+		return ret;
+
+	reset_control_assert(reset);
+	usleep_range(10000, 12000);
+	reset_control_deassert(reset);
+
+	clk_disable_unprepare(ci->fs_clk);
+
+	ret = clk_prepare_enable(ci->core_clk);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(ci->iface_clk);
+	if (ret)
+		goto err_iface;
+
 	plat_ci = ci_hdrc_add_device(&pdev->dev,
 				pdev->resource, pdev->num_resources,
 				&ci_hdrc_msm_platdata);
 	if (IS_ERR(plat_ci)) {
 		dev_err(&pdev->dev, "ci_hdrc_add_device failed!\n");
-		return PTR_ERR(plat_ci);
+		ret = PTR_ERR(plat_ci);
+		goto err_mux;
 	}
 
-	platform_set_drvdata(pdev, plat_ci);
+	ci->ci = plat_ci;
 
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_no_callbacks(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
 	return 0;
+
+err_mux:
+	clk_disable_unprepare(ci->iface_clk);
+err_iface:
+	clk_disable_unprepare(ci->core_clk);
+	return ret;
 }
 
 static int ci_hdrc_msm_remove(struct platform_device *pdev)
 {
-	struct platform_device *plat_ci = platform_get_drvdata(pdev);
+	struct ci_hdrc_msm *ci = platform_get_drvdata(pdev);
 
 	pm_runtime_disable(&pdev->dev);
-	ci_hdrc_remove_device(plat_ci);
+	ci_hdrc_remove_device(ci->ci);
+	clk_disable_unprepare(ci->iface_clk);
+	clk_disable_unprepare(ci->core_clk);
 
 	return 0;
 }
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548101 — [PATCH v6 08/25] usb: chipidea: Remove locking in ci_udc_start()

We don't call hw_device_reset() with the ci->lock held, so it
doesn't seem like this lock here is protecting anything. Let's
just remove it. This allows us to call sleeping functions like
phy_init() from within the CI_HDRC_CONTROLLER_RESET_EVENT hook.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/udc.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index cf132f057137..732b281485de 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -1725,7 +1725,6 @@ static int ci_udc_start(struct usb_gadget *gadget,
 			 struct usb_gadget_driver *driver)
 {
 	struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget);
-	unsigned long flags;
 	int retval = -ENOMEM;
 
 	if (driver->disconnect == NULL)
@@ -1752,7 +1751,6 @@ static int ci_udc_start(struct usb_gadget *gadget,
 
 	pm_runtime_get_sync(&ci->gadget.dev);
 	if (ci->vbus_active) {
-		spin_lock_irqsave(&ci->lock, flags);
 		hw_device_reset(ci);
 	} else {
 		usb_udc_vbus_handler(&ci->gadget, false);
@@ -1761,7 +1759,6 @@ static int ci_udc_start(struct usb_gadget *gadget,
 	}
 
 	retval = hw_device_state(ci, ci->ep0out->qh.dma);
-	spin_unlock_irqrestore(&ci->lock, flags);
 	if (retval)
 		pm_runtime_put_sync(&ci->gadget.dev);
 
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548102 — [PATCH v6 14/25] usb: chipidea: msm: Use hw_write_id_reg() instead of writel

The MSM_USB_BASE macro trick is not very clear, and we're using
it for only one register write so let's just move to using
hw_write_id_reg() and passing the ci pointer instead. That
clearly shows what offset we're using and avoids needing to
include the msm_hsusb_hw.h file when we're going to delete that
file soon.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/ci_hdrc_msm.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
index 719b20caf88e..b282a717bf8c 100644
--- a/drivers/usb/chipidea/ci_hdrc_msm.c
+++ b/drivers/usb/chipidea/ci_hdrc_msm.c
@@ -8,14 +8,12 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
-#include <linux/usb/msm_hsusb_hw.h>
-#include <linux/usb/ulpi.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/chipidea.h>
 
 #include "ci.h"
 
-#define MSM_USB_BASE	(ci->hw_bank.abs)
+#define HS_PHY_AHB_MODE			0x0098
 
 static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
 {
@@ -25,7 +23,7 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
 	case CI_HDRC_CONTROLLER_RESET_EVENT:
 		dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
 		/* use AHB transactor, allow posted data writes */
-		writel(0x8, USB_AHBMODE);
+		hw_write_id_reg(ci, HS_PHY_AHB_MODE, 0xffffffff, 0x8);
 		usb_phy_init(ci->usb_phy);
 		break;
 	case CI_HDRC_CONTROLLER_STOPPED_EVENT:
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548103 — [PATCH v6 04/25] usb: chipidea: Only read/write OTGSC from one place

With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/ci.h   |  3 ---
 drivers/usb/chipidea/core.c | 32 --------------------------------
 drivers/usb/chipidea/otg.c  | 34 ++++++++++++++++++++++++++++++----
 3 files changed, 30 insertions(+), 39 deletions(-)

diff --git a/drivers/usb/chipidea/ci.h b/drivers/usb/chipidea/ci.h
index cd414559040f..05bc4d631cb9 100644
--- a/drivers/usb/chipidea/ci.h
+++ b/drivers/usb/chipidea/ci.h
@@ -428,9 +428,6 @@ int hw_port_test_set(struct ci_hdrc *ci, u8 mode);
 
 u8 hw_port_test_get(struct ci_hdrc *ci);
 
-int hw_wait_reg(struct ci_hdrc *ci, enum ci_hw_regs reg, u32 mask,
-				u32 value, unsigned int timeout_ms);
-
 void ci_platform_configure(struct ci_hdrc *ci);
 
 int dbg_create_files(struct ci_hdrc *ci);
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 3dbb4a21ab44..6e0d614a8075 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -516,38 +516,6 @@ int hw_device_reset(struct ci_hdrc *ci)
 	return 0;
 }
 
-/**
- * hw_wait_reg: wait the register value
- *
- * Sometimes, it needs to wait register value before going on.
- * Eg, when switch to device mode, the vbus value should be lower
- * than OTGSC_BSV before connects to host.
- *
- * @ci: the controller
- * @reg: register index
- * @mask: mast bit
- * @value: the bit value to wait
- * @timeout_ms: timeout in millisecond
- *
- * This function returns an error code if timeout
- */
-int hw_wait_reg(struct ci_hdrc *ci, enum ci_hw_regs reg, u32 mask,
-				u32 value, unsigned int timeout_ms)
-{
-	unsigned long elapse = jiffies + msecs_to_jiffies(timeout_ms);
-
-	while (hw_read(ci, reg, mask) != value) {
-		if (time_after(jiffies, elapse)) {
-			dev_err(ci->dev, "timeout waiting for %08x in %d\n",
-					mask, reg);
-			return -ETIMEDOUT;
-		}
-		msleep(20);
-	}
-
-	return 0;
-}
-
 static irqreturn_t ci_irq(int irq, void *data)
 {
 	struct ci_hdrc *ci = data;
diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
index 03b6743461d1..a829607c3e4d 100644
--- a/drivers/usb/chipidea/otg.c
+++ b/drivers/usb/chipidea/otg.c
@@ -104,7 +104,31 @@ void ci_handle_vbus_change(struct ci_hdrc *ci)
 		usb_gadget_vbus_disconnect(&ci->gadget);
 }
 
-#define CI_VBUS_STABLE_TIMEOUT_MS 5000
+/**
+ * When we switch to device mode, the vbus value should be lower
+ * than OTGSC_BSV before connecting to host.
+ *
+ * @ci: the controller
+ *
+ * This function returns an error code if timeout
+ */
+static int hw_wait_vbus_lower_bsv(struct ci_hdrc *ci)
+{
+	unsigned long elapse = jiffies + msecs_to_jiffies(5000);
+	u32 mask = OTGSC_BSV;
+
+	while (hw_read_otgsc(ci, mask)) {
+		if (time_after(jiffies, elapse)) {
+			dev_err(ci->dev, "timeout waiting for %08x in OTGSC\n",
+					mask);
+			return -ETIMEDOUT;
+		}
+		msleep(20);
+	}
+
+	return 0;
+}
+
 static void ci_handle_id_switch(struct ci_hdrc *ci)
 {
 	enum ci_role role = ci_otg_role(ci);
@@ -116,9 +140,11 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
 		ci_role_stop(ci);
 
 		if (role == CI_ROLE_GADGET)
-			/* wait vbus lower than OTGSC_BSV */
-			hw_wait_reg(ci, OP_OTGSC, OTGSC_BSV, 0,
-					CI_VBUS_STABLE_TIMEOUT_MS);
+			/*
+			 * wait vbus lower than OTGSC_BSV before connecting
+			 * to host
+			 */
+			hw_wait_vbus_lower_bsv(ci);
 
 		ci_role_start(ci, role);
 	}
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548104 — [PATCH v6 06/25] usb: chipidea: Add platform flag for wrapper phy management

The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly.
Therefore, add a flag to skip any phy power management in the
core layer, leaving it up to the glue driver to manage.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/core.c  | 6 ++++++
 include/linux/usb/chipidea.h | 1 +
 2 files changed, 7 insertions(+)

diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 6e0d614a8075..3d15aee84a6a 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -361,6 +361,9 @@ static int _ci_usb_phy_init(struct ci_hdrc *ci)
  */
 static void ci_usb_phy_exit(struct ci_hdrc *ci)
 {
+	if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL)
+		return;
+
 	if (ci->phy) {
 		phy_power_off(ci->phy);
 		phy_exit(ci->phy);
@@ -379,6 +382,9 @@ static int ci_usb_phy_init(struct ci_hdrc *ci)
 {
 	int ret;
 
+	if (ci->platdata->flags & CI_HDRC_OVERRIDE_PHY_CONTROL)
+		return 0;
+
 	switch (ci->platdata->phy_mode) {
 	case USBPHY_INTERFACE_MODE_UTMI:
 	case USBPHY_INTERFACE_MODE_UTMIW:
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index f9be467d6695..d07b162073f7 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -57,6 +57,7 @@ struct ci_hdrc_platform_data {
 #define CI_HDRC_OVERRIDE_AHB_BURST	BIT(9)
 #define CI_HDRC_OVERRIDE_TX_BURST	BIT(10)
 #define CI_HDRC_OVERRIDE_RX_BURST	BIT(11)
+#define CI_HDRC_OVERRIDE_PHY_CONTROL	BIT(12) /* Glue layer manages phy */
 	enum usb_dr_mode	dr_mode;
 #define CI_HDRC_CONTROLLER_RESET_EVENT		0
 #define CI_HDRC_CONTROLLER_STOPPED_EVENT	1
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548105 — [PATCH v6 13/25] usb: chipidea: msm: Rely on core to override AHBBURST

The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/ci_hdrc_msm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
index 89c1a02d69b5..719b20caf88e 100644
--- a/drivers/usb/chipidea/ci_hdrc_msm.c
+++ b/drivers/usb/chipidea/ci_hdrc_msm.c
@@ -24,7 +24,6 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
 	switch (event) {
 	case CI_HDRC_CONTROLLER_RESET_EVENT:
 		dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
-		writel(0, USB_AHBBURST);
 		/* use AHB transactor, allow posted data writes */
 		writel(0x8, USB_AHBMODE);
 		usb_phy_init(ci->usb_phy);
@@ -47,7 +46,8 @@ static struct ci_hdrc_platform_data ci_hdrc_msm_platdata = {
 	.name			= "ci_hdrc_msm",
 	.capoffset		= DEF_CAPOFFSET,
 	.flags			= CI_HDRC_REGS_SHARED |
-				  CI_HDRC_DISABLE_STREAMING,
+				  CI_HDRC_DISABLE_STREAMING |
+				  CI_HDRC_OVERRIDE_AHB_BURST,
 
 	.notify_event		= ci_hdrc_msm_notify_event,
 };
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548106 — [PATCH v6 10/25] usb: chipidea: Consolidate extcon notifiers

The two extcon notifiers are almost the same except for the
variable name for the cable structure and the id notifier inverts
the cable->state logic. Make it the same and replace two
functions with one to save some lines. This also makes it so that
the id cable state is true when the id pin is pulled low, so we
change the name of ->state to ->connected to properly reflect
that we're interested in the cable being connected.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/core.c  | 45 ++++++++++++--------------------------------
 drivers/usb/chipidea/otg.c   |  8 ++++----
 include/linux/usb/chipidea.h |  4 ++--
 3 files changed, 18 insertions(+), 39 deletions(-)

diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 83adbb0ad509..8a020ebbbe2f 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -577,35 +577,14 @@ static irqreturn_t ci_irq(int irq, void *data)
 	return ret;
 }
 
-static int ci_vbus_notifier(struct notifier_block *nb, unsigned long event,
-			    void *ptr)
+static int ci_cable_notifier(struct notifier_block *nb, unsigned long event,
+			     void *ptr)
 {
-	struct ci_hdrc_cable *vbus = container_of(nb, struct ci_hdrc_cable, nb);
-	struct ci_hdrc *ci = vbus->ci;
+	struct ci_hdrc_cable *cbl = container_of(nb, struct ci_hdrc_cable, nb);
+	struct ci_hdrc *ci = cbl->ci;
 
-	if (event)
-		vbus->state = true;
-	else
-		vbus->state = false;
-
-	vbus->changed = true;
-
-	ci_irq(ci->irq, ci);
-	return NOTIFY_DONE;
-}
-
-static int ci_id_notifier(struct notifier_block *nb, unsigned long event,
-			  void *ptr)
-{
-	struct ci_hdrc_cable *id = container_of(nb, struct ci_hdrc_cable, nb);
-	struct ci_hdrc *ci = id->ci;
-
-	if (event)
-		id->state = false;
-	else
-		id->state = true;
-
-	id->changed = true;
+	cbl->connected = event;
+	cbl->changed = true;
 
 	ci_irq(ci->irq, ci);
 	return NOTIFY_DONE;
@@ -714,27 +693,27 @@ static int ci_get_platdata(struct device *dev,
 	}
 
 	cable = &platdata->vbus_extcon;
-	cable->nb.notifier_call = ci_vbus_notifier;
+	cable->nb.notifier_call = ci_cable_notifier;
 	cable->edev = ext_vbus;
 
 	if (!IS_ERR(ext_vbus)) {
 		ret = extcon_get_cable_state_(cable->edev, EXTCON_USB);
 		if (ret)
-			cable->state = true;
+			cable->connected = true;
 		else
-			cable->state = false;
+			cable->connected = false;
 	}
 
 	cable = &platdata->id_extcon;
-	cable->nb.notifier_call = ci_id_notifier;
+	cable->nb.notifier_call = ci_cable_notifier;
 	cable->edev = ext_id;
 
 	if (!IS_ERR(ext_id)) {
 		ret = extcon_get_cable_state_(cable->edev, EXTCON_USB_HOST);
 		if (ret)
-			cable->state = false;
+			cable->connected = true;
 		else
-			cable->state = true;
+			cable->connected = false;
 	}
 	return 0;
 }
diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
index 0cf149edddd8..695f3fe3ae21 100644
--- a/drivers/usb/chipidea/otg.c
+++ b/drivers/usb/chipidea/otg.c
@@ -44,7 +44,7 @@ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask)
 		else
 			val &= ~OTGSC_BSVIS;
 
-		if (cable->state)
+		if (cable->connected)
 			val |= OTGSC_BSV;
 		else
 			val &= ~OTGSC_BSV;
@@ -62,10 +62,10 @@ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask)
 		else
 			val &= ~OTGSC_IDIS;
 
-		if (cable->state)
-			val |= OTGSC_ID;
+		if (cable->connected)
+			val &= ~OTGSC_ID; /* host */
 		else
-			val &= ~OTGSC_ID;
+			val |= OTGSC_ID; /* device */
 
 		if (cable->enabled)
 			val |= OTGSC_IDIE;
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index d07b162073f7..7e3daa37cf60 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -12,7 +12,7 @@ struct ci_hdrc;
 
 /**
  * struct ci_hdrc_cable - structure for external connector cable state tracking
- * @state: current state of the line
+ * @connected: true if cable is connected, false otherwise
  * @changed: set to true when extcon event happen
  * @enabled: set to true if we've enabled the vbus or id interrupt
  * @edev: device which generate events
@@ -21,7 +21,7 @@ struct ci_hdrc;
  * @conn: used for notification registration
  */
 struct ci_hdrc_cable {
-	bool				state;
+	bool				connected;
 	bool				changed;
 	bool				enabled;
 	struct extcon_dev		*edev;
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548107 — [PATCH v6 05/25] usb: chipidea: Handle extcon events properly

We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/otg.c   | 46 +++++++++++++++++++++++++++++++++++++++-----
 include/linux/usb/chipidea.h |  2 ++
 2 files changed, 43 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
index a829607c3e4d..0cf149edddd8 100644
--- a/drivers/usb/chipidea/otg.c
+++ b/drivers/usb/chipidea/otg.c
@@ -44,12 +44,15 @@ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask)
 		else
 			val &= ~OTGSC_BSVIS;
 
-		cable->changed = false;
-
 		if (cable->state)
 			val |= OTGSC_BSV;
 		else
 			val &= ~OTGSC_BSV;
+
+		if (cable->enabled)
+			val |= OTGSC_BSVIE;
+		else
+			val &= ~OTGSC_BSVIE;
 	}
 
 	cable = &ci->platdata->id_extcon;
@@ -59,15 +62,18 @@ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask)
 		else
 			val &= ~OTGSC_IDIS;
 
-		cable->changed = false;
-
 		if (cable->state)
 			val |= OTGSC_ID;
 		else
 			val &= ~OTGSC_ID;
+
+		if (cable->enabled)
+			val |= OTGSC_IDIE;
+		else
+			val &= ~OTGSC_IDIE;
 	}
 
-	return val;
+	return val & mask;
 }
 
 /**
@@ -77,6 +83,36 @@ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask)
  */
 void hw_write_otgsc(struct ci_hdrc *ci, u32 mask, u32 data)
 {
+	struct ci_hdrc_cable *cable;
+
+	cable = &ci->platdata->vbus_extcon;
+	if (!IS_ERR(cable->edev)) {
+		if (data & mask & OTGSC_BSVIS)
+			cable->changed = false;
+
+		/* Don't enable vbus interrupt if using external notifier */
+		if (data & mask & OTGSC_BSVIE) {
+			cable->enabled = true;
+			data &= ~OTGSC_BSVIE;
+		} else if (mask & OTGSC_BSVIE) {
+			cable->enabled = false;
+		}
+	}
+
+	cable = &ci->platdata->id_extcon;
+	if (!IS_ERR(cable->edev)) {
+		if (data & mask & OTGSC_IDIS)
+			cable->changed = false;
+
+		/* Don't enable id interrupt if using external notifier */
+		if (data & mask & OTGSC_IDIE) {
+			cable->enabled = true;
+			data &= ~OTGSC_IDIE;
+		} else if (mask & OTGSC_IDIE) {
+			cable->enabled = false;
+		}
+	}
+
 	hw_write(ci, OP_OTGSC, mask | OTGSC_INT_STATUS_BITS, data);
 }
 
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index 5dd75fa47dd8..f9be467d6695 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -14,6 +14,7 @@ struct ci_hdrc;
  * struct ci_hdrc_cable - structure for external connector cable state tracking
  * @state: current state of the line
  * @changed: set to true when extcon event happen
+ * @enabled: set to true if we've enabled the vbus or id interrupt
  * @edev: device which generate events
  * @ci: driver state of the chipidea device
  * @nb: hold event notification callback
@@ -22,6 +23,7 @@ struct ci_hdrc;
 struct ci_hdrc_cable {
 	bool				state;
 	bool				changed;
+	bool				enabled;
 	struct extcon_dev		*edev;
 	struct ci_hdrc			*ci;
 	struct notifier_block		nb;
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548108 — [PATCH v6 11/25] usb: chipidea: vbus event may exist before starting gadget

From: Peter Chen <peter.chen@nxp.com>

At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switch to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
[sboyd@codeaurora.org: Modify comment text per list discussion]
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/core.c |  4 ----
 drivers/usb/chipidea/otg.c  | 14 +++++++++-----
 drivers/usb/chipidea/udc.c  |  2 ++
 3 files changed, 11 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 8a020ebbbe2f..37f888e31f10 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -979,10 +979,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 	}
 
 	if (!ci_otg_is_fsm_mode(ci)) {
-		/* only update vbus status for peripheral */
-		if (ci->role == CI_ROLE_GADGET)
-			ci_handle_vbus_change(ci);
-
 		ret = ci_role_start(ci, ci->role);
 		if (ret) {
 			dev_err(dev, "can't start %s role\n",
diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
index 695f3fe3ae21..c972ed23b8ec 100644
--- a/drivers/usb/chipidea/otg.c
+++ b/drivers/usb/chipidea/otg.c
@@ -134,9 +134,9 @@ void ci_handle_vbus_change(struct ci_hdrc *ci)
 	if (!ci->is_otg)
 		return;
 
-	if (hw_read_otgsc(ci, OTGSC_BSV))
+	if (hw_read_otgsc(ci, OTGSC_BSV) && !ci->vbus_active)
 		usb_gadget_vbus_connect(&ci->gadget);
-	else
+	else if (!hw_read_otgsc(ci, OTGSC_BSV) && ci->vbus_active)
 		usb_gadget_vbus_disconnect(&ci->gadget);
 }
 
@@ -175,10 +175,14 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
 
 		ci_role_stop(ci);
 
-		if (role == CI_ROLE_GADGET)
+		if (role == CI_ROLE_GADGET &&
+				IS_ERR(ci->platdata->vbus_extcon.edev))
 			/*
-			 * wait vbus lower than OTGSC_BSV before connecting
-			 * to host
+			 * wait vbus lower than OTGSC_BSV before connecting to
+			 * host. If connecting status is from an external
+			 * connector instead of register, we don't need to care
+			 * vbus on the board, since it will not affect external
+			 * connector status.
 			 */
 			hw_wait_vbus_lower_bsv(ci);
 
diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index 732b281485de..0db56fb7e9e9 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -1961,6 +1961,8 @@ static int udc_id_switch_for_device(struct ci_hdrc *ci)
 		/* Clear and enable BSV irq */
 		hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE,
 					OTGSC_BSVIS | OTGSC_BSVIE);
+	/* vbus change may has already been occurred */
+	ci_handle_vbus_change(ci);
 
 	return 0;
 }
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1549588 — Re: [PATCH v6 11/25] usb: chipidea: vbus event may exist before starting gadget

On Wed, Dec 28, 2016 at 02:56:57PM -0800, Stephen Boyd wrote:
> From: Peter Chen <peter.chen@nxp.com>
> 
> At some situations, the vbus may already be there before starting
> gadget. So we need to check vbus event after switch to gadget in
> order to handle missing vbus event. The typical use cases are plugging
> vbus cable before driver load or the vbus has already been there
> after stopping host but before starting gadget.
> 
> Signed-off-by: Peter Chen <peter.chen@nxp.com>
> Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
> Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
> [sboyd@codeaurora.org: Modify comment text per list discussion]
> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
> ---
>  drivers/usb/chipidea/core.c |  4 ----
>  drivers/usb/chipidea/otg.c  | 14 +++++++++-----
>  drivers/usb/chipidea/udc.c  |  2 ++
>  3 files changed, 11 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
> index 8a020ebbbe2f..37f888e31f10 100644
> --- a/drivers/usb/chipidea/core.c
> +++ b/drivers/usb/chipidea/core.c
> @@ -979,10 +979,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
>  	}
>  
>  	if (!ci_otg_is_fsm_mode(ci)) {
> -		/* only update vbus status for peripheral */
> -		if (ci->role == CI_ROLE_GADGET)
> -			ci_handle_vbus_change(ci);
> -
>  		ret = ci_role_start(ci, ci->role);
>  		if (ret) {
>  			dev_err(dev, "can't start %s role\n",
> diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
> index 695f3fe3ae21..c972ed23b8ec 100644
> --- a/drivers/usb/chipidea/otg.c
> +++ b/drivers/usb/chipidea/otg.c
> @@ -134,9 +134,9 @@ void ci_handle_vbus_change(struct ci_hdrc *ci)
>  	if (!ci->is_otg)
>  		return;
>  
> -	if (hw_read_otgsc(ci, OTGSC_BSV))
> +	if (hw_read_otgsc(ci, OTGSC_BSV) && !ci->vbus_active)
>  		usb_gadget_vbus_connect(&ci->gadget);
> -	else
> +	else if (!hw_read_otgsc(ci, OTGSC_BSV) && ci->vbus_active)
>  		usb_gadget_vbus_disconnect(&ci->gadget);
>  }
>  
> @@ -175,10 +175,14 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
>  
>  		ci_role_stop(ci);
>  
> -		if (role == CI_ROLE_GADGET)
> +		if (role == CI_ROLE_GADGET &&
> +				IS_ERR(ci->platdata->vbus_extcon.edev))
>  			/*
> -			 * wait vbus lower than OTGSC_BSV before connecting
> -			 * to host
> +			 * wait vbus lower than OTGSC_BSV before connecting to
> +			 * host. If connecting status is from an external
> +			 * connector instead of register, we don't need to care
> +			 * vbus on the board, since it will not affect external
> +			 * connector status.
>  			 */
>  			hw_wait_vbus_lower_bsv(ci);
>  
> diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
> index 732b281485de..0db56fb7e9e9 100644
> --- a/drivers/usb/chipidea/udc.c
> +++ b/drivers/usb/chipidea/udc.c
> @@ -1961,6 +1961,8 @@ static int udc_id_switch_for_device(struct ci_hdrc *ci)
>  		/* Clear and enable BSV irq */
>  		hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE,
>  					OTGSC_BSVIS | OTGSC_BSVIE);
> +	/* vbus change may has already been occurred */
> +	ci_handle_vbus_change(ci);
>  
>  	return 0;

After thinking more, the above change will affect OTG FSM which calls
this API too, but handle vbus change later, see ci_otg_start_host and
ci_otg_start_gadget. How about changing patch like below:

 drivers/usb/chipidea/otg.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
index 695f3fe..10236fe 100644
--- a/drivers/usb/chipidea/otg.c
+++ b/drivers/usb/chipidea/otg.c
@@ -134,9 +134,9 @@ void ci_handle_vbus_change(struct ci_hdrc *ci)
 	if (!ci->is_otg)
 		return;
 
-	if (hw_read_otgsc(ci, OTGSC_BSV))
+	if (hw_read_otgsc(ci, OTGSC_BSV) && !ci->vbus_active)
 		usb_gadget_vbus_connect(&ci->gadget);
-	else
+	else if (!hw_read_otgsc(ci, OTGSC_BSV) && ci->vbus_active)
 		usb_gadget_vbus_disconnect(&ci->gadget);
 }
 
@@ -175,14 +175,21 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
 
 		ci_role_stop(ci);
 
-		if (role == CI_ROLE_GADGET)
+		if (role == CI_ROLE_GADGET &&
+				IS_ERR(ci->platdata->vbus_extcon.edev))
 			/*
-			 * wait vbus lower than OTGSC_BSV before connecting
-			 * to host
+			 * Wait vbus lower than OTGSC_BSV before connecting
+			 * to host. If connecting status is from an external
+			 * connector instead of register, we don't need to
+			 * care vbus on the board, since it will not affect
+			 * external connector status.
 			 */
 			hw_wait_vbus_lower_bsv(ci);
 
 		ci_role_start(ci, role);
+		/* vbus change may have already occurred */
+		if (role == CI_ROLE_GADGET)
+			ci_handle_vbus_change(ci);
 	}
 }
 /**
-- 
2.7.4

-- 

Best Regards,
Peter Chen

[toc] | [prev] | [next] | [standalone]

#1557266 — Re: [PATCH v6 11/25] usb: chipidea: vbus event may exist before starting gadget

On Wed, Jan 11, 2017 at 04:32:34PM -0800, Stephen Boyd wrote:
> Quoting Peter Chen (2017-01-03 00:00:31)
> > On Wed, Dec 28, 2016 at 02:56:57PM -0800, Stephen Boyd wrote:
> > > From: Peter Chen <peter.chen@nxp.com>
> > > 
> > > At some situations, the vbus may already be there before starting
> > > gadget. So we need to check vbus event after switch to gadget in
> > > order to handle missing vbus event. The typical use cases are plugging
> > > vbus cable before driver load or the vbus has already been there
> > > after stopping host but before starting gadget.
> > > 
> > > Signed-off-by: Peter Chen <peter.chen@nxp.com>
> > > Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
> > > Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
> > > [sboyd@codeaurora.org: Modify comment text per list discussion]
> > > Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
> > > ---
> > >  drivers/usb/chipidea/core.c |  4 ----
> > >  drivers/usb/chipidea/otg.c  | 14 +++++++++-----
> > >  drivers/usb/chipidea/udc.c  |  2 ++
> > >  3 files changed, 11 insertions(+), 9 deletions(-)
> > > 
> > > diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
> > > index 8a020ebbbe2f..37f888e31f10 100644
> > > --- a/drivers/usb/chipidea/core.c
> > > +++ b/drivers/usb/chipidea/core.c
> > > @@ -979,10 +979,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
> > >       }
> > >  
> > >       if (!ci_otg_is_fsm_mode(ci)) {
> > > -             /* only update vbus status for peripheral */
> > > -             if (ci->role == CI_ROLE_GADGET)
> > > -                     ci_handle_vbus_change(ci);
> > > -
> > >               ret = ci_role_start(ci, ci->role);
> > >               if (ret) {
> > >                       dev_err(dev, "can't start %s role\n",
> > > diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
> > > index 695f3fe3ae21..c972ed23b8ec 100644
> > > --- a/drivers/usb/chipidea/otg.c
> > > +++ b/drivers/usb/chipidea/otg.c
> > > @@ -134,9 +134,9 @@ void ci_handle_vbus_change(struct ci_hdrc *ci)
> > >       if (!ci->is_otg)
> > >               return;
> > >  
> > > -     if (hw_read_otgsc(ci, OTGSC_BSV))
> > > +     if (hw_read_otgsc(ci, OTGSC_BSV) && !ci->vbus_active)
> > >               usb_gadget_vbus_connect(&ci->gadget);
> > > -     else
> > > +     else if (!hw_read_otgsc(ci, OTGSC_BSV) && ci->vbus_active)
> > >               usb_gadget_vbus_disconnect(&ci->gadget);
> > >  }
> > >  
> > > @@ -175,10 +175,14 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
> > >  
> > >               ci_role_stop(ci);
> > >  
> > > -             if (role == CI_ROLE_GADGET)
> > > +             if (role == CI_ROLE_GADGET &&
> > > +                             IS_ERR(ci->platdata->vbus_extcon.edev))
> > >                       /*
> > > -                      * wait vbus lower than OTGSC_BSV before connecting
> > > -                      * to host
> > > +                      * wait vbus lower than OTGSC_BSV before connecting to
> > > +                      * host. If connecting status is from an external
> > > +                      * connector instead of register, we don't need to care
> > > +                      * vbus on the board, since it will not affect external
> > > +                      * connector status.
> > >                        */
> > >                       hw_wait_vbus_lower_bsv(ci);
> > >  
> > > diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
> > > index 732b281485de..0db56fb7e9e9 100644
> > > --- a/drivers/usb/chipidea/udc.c
> > > +++ b/drivers/usb/chipidea/udc.c
> > > @@ -1961,6 +1961,8 @@ static int udc_id_switch_for_device(struct ci_hdrc *ci)
> > >               /* Clear and enable BSV irq */
> > >               hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE,
> > >                                       OTGSC_BSVIS | OTGSC_BSVIE);
> > > +     /* vbus change may has already been occurred */
> > > +     ci_handle_vbus_change(ci);
> > >  
> > >       return 0;
> > 
> > After thinking more, the above change will affect OTG FSM which calls
> > this API too, but handle vbus change later, see ci_otg_start_host and
> > ci_otg_start_gadget. How about changing patch like below:
> 
> Ok. I'll give it a spin but I think that should work too. I don't have
> any hardware to test the OTG FSM to make sure things don't break.

ci_handle_id_switch is only called at non OTG FSM mode, so it will not
affect OTG FSM.

-- 

Best Regards,
Peter Chen

[toc] | [prev] | [next] | [standalone]

#1548109 — [PATCH v6 02/25] of: device: Export of_device_{get_modalias,uvent_modalias} to modules

The ULPI bus can be built as a module, and it will soon be
calling these functions when it supports probing devices from DT.
Export them so they can be used by the ULPI module.

Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/of/device.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/of/device.c b/drivers/of/device.c
index 8a22a253a830..b1e6bebda3f3 100644
--- a/drivers/of/device.c
+++ b/drivers/of/device.c
@@ -225,6 +225,7 @@ ssize_t of_device_get_modalias(struct device *dev, char *str, ssize_t len)
 
 	return tsize;
 }
+EXPORT_SYMBOL_GPL(of_device_get_modalias);
 
 int of_device_request_module(struct device *dev)
 {
@@ -310,3 +311,4 @@ int of_device_uevent_modalias(struct device *dev, struct kobj_uevent_env *env)
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(of_device_uevent_modalias);
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [next] | [standalone]

#1548113 — [PATCH v6 16/25] usb: chipidea: msm: Mux over secondary phy at the right time

We need to pick the correct phy at runtime based on how the SoC
has been wired onto the board. If the secondary phy is used, take
it out of reset and mux over to it by writing into the TCSR
register. Make sure to do this on reset too, because this
register is reset to the default value (primary phy) after the
RESET bit is set in USBCMD.

Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/ci_hdrc_msm.c | 62 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 60 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
index 7e870a253f55..4b0aadc2be2f 100644
--- a/drivers/usb/chipidea/ci_hdrc_msm.c
+++ b/drivers/usb/chipidea/ci_hdrc_msm.c
@@ -8,29 +8,44 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
-#include <linux/usb/gadget.h>
 #include <linux/usb/chipidea.h>
 #include <linux/clk.h>
 #include <linux/reset.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/io.h>
 
 #include "ci.h"
 
 #define HS_PHY_AHB_MODE			0x0098
 
+/* Vendor base starts at 0x200 beyond CI base */
+#define HS_PHY_SEC_CTRL			0x0078
+#define HS_PHY_DIG_CLAMP_N		BIT(16)
+
 struct ci_hdrc_msm {
 	struct platform_device *ci;
 	struct clk *core_clk;
 	struct clk *iface_clk;
 	struct clk *fs_clk;
+	bool secondary_phy;
+	void __iomem *base;
 };
 
 static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
 {
-	struct device *dev = ci->gadget.dev.parent;
+	struct device *dev = ci->dev->parent;
+	struct ci_hdrc_msm *msm_ci = dev_get_drvdata(dev);
 
 	switch (event) {
 	case CI_HDRC_CONTROLLER_RESET_EVENT:
 		dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
+		if (msm_ci->secondary_phy) {
+			u32 val = readl_relaxed(msm_ci->base + HS_PHY_SEC_CTRL);
+			val |= HS_PHY_DIG_CLAMP_N;
+			writel_relaxed(val, msm_ci->base + HS_PHY_SEC_CTRL);
+		}
+
 		/* use AHB transactor, allow posted data writes */
 		hw_write_id_reg(ci, HS_PHY_AHB_MODE, 0xffffffff, 0x8);
 		usb_phy_init(ci->usb_phy);
@@ -59,6 +74,39 @@ static struct ci_hdrc_platform_data ci_hdrc_msm_platdata = {
 	.notify_event		= ci_hdrc_msm_notify_event,
 };
 
+static int ci_hdrc_msm_mux_phy(struct ci_hdrc_msm *ci,
+			       struct platform_device *pdev)
+{
+	struct regmap *regmap;
+	struct device *dev = &pdev->dev;
+	struct of_phandle_args args;
+	u32 val;
+	int ret;
+
+	ret = of_parse_phandle_with_fixed_args(dev->of_node, "phy-select", 2, 0,
+					       &args);
+	if (ret)
+		return 0;
+
+	regmap = syscon_node_to_regmap(args.np);
+	of_node_put(args.np);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	ret = regmap_write(regmap, args.args[0], args.args[1]);
+	if (ret)
+		return ret;
+
+	ci->secondary_phy = !!args.args[1];
+	if (ci->secondary_phy) {
+		val = readl_relaxed(ci->base + HS_PHY_SEC_CTRL);
+		val |= HS_PHY_DIG_CLAMP_N;
+		writel_relaxed(val, ci->base + HS_PHY_SEC_CTRL);
+	}
+
+	return 0;
+}
+
 static int ci_hdrc_msm_probe(struct platform_device *pdev)
 {
 	struct ci_hdrc_msm *ci;
@@ -66,6 +114,7 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
 	struct usb_phy *phy;
 	struct clk *clk;
 	struct reset_control *reset;
+	struct resource *res;
 	int ret;
 
 	dev_dbg(&pdev->dev, "ci_hdrc_msm_probe\n");
@@ -105,6 +154,11 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
 		ci->fs_clk = NULL;
 	}
 
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	ci->base = devm_ioremap_resource(&pdev->dev, res);
+	if (!ci->base)
+		return -ENOMEM;
+
 	ret = clk_prepare_enable(ci->fs_clk);
 	if (ret)
 		return ret;
@@ -123,6 +177,10 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_iface;
 
+	ret = ci_hdrc_msm_mux_phy(ci, pdev);
+	if (ret)
+		goto err_mux;
+
 	plat_ci = ci_hdrc_add_device(&pdev->dev,
 				pdev->resource, pdev->num_resources,
 				&ci_hdrc_msm_platdata);
-- 
2.10.0.297.gf6727b0

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web