Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1338602 > unrolled thread

Re: 4.5-rc4 kernel is failed to bootup on CN6880

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  Re: 4.5-rc4 kernel is failed to bootup on CN6880 David Daney <ddaney@caviumnetworks.com> - 2016-02-20 02:20 +0100
    Re: 4.5-rc4 kernel is failed to bootup on CN6880 Yang Shi <yang.shi@windriver.com> - 2016-02-20 02:30 +0100

#1338602 — Re: 4.5-rc4 kernel is failed to bootup on CN6880

On 02/19/2016 05:12 PM, Yang Shi wrote:
> Hi David,
>
> I tried to boot 4.5-rc4 kernel on my CN6880 board, but it is failed at
> booting up secondary cores. The error is:

Have you had luck with any other kernel.org versions?

FWIW, I recently posed some patches that may help.  I haven't recently 
tested on cn68xx though, so I can't really say what it might be.


>
> CPU31 revision is: 000d9101 (Cavium Octeon II)
> SMP: Booting CPU32 (CoreId 32)...
> Secondary boot timeout
>
> I passed "numcores=32" in kernel commandline since there are 32 cores
> ion CN6880. And, the bootloader information is as below:
>
> U-Boot 2013.07 ( (U-BOOT build: 104, SDK version: 3.1.1-544),
> svnversion: u-boot:107133M, exec:)-svn107117 (Build time: Oct 31 2014 -
> 19:39:37)
>
> Skipping PCIe port 0 BIST, reset not done. (port not configured)
> Skipping PCIe port 1 BIST, reset not done. (port not configured)
> BIST check passed.
> EBB6800 board revision major:2, minor:0, serial #: 2011-2.0-00120
> OCTEON CN6880-AAP pass 1.1, Core clock: 1200 MHz, IO clock: 800 MHz, DDR
> clock: 667 MHz (1334 Mhz DDR)
> Base DRAM address used by u-boot: 0x20f000000, size: 0x1000000
> DRAM: 8 GiB
> Clearing DRAM...... done
> NAND:  4096 MiB
> Registered IDE device 0 from IDE bus:dev 0:0
> Flash: 8 MiB
> 0:PCIe: Port 0 is unknown, skipping.
> 0:PCIe: Port 1 is unknown, skipping.
> PCI console init succeeded, 1 consoles, 1024 bytes each
> Net:   octmgmt0, octeth0, octeth1, octeth2, octeth3
> Bus 0: OK
>    Device 0: Model: CF 1GB Firm: 20071116 Ser#: TSS20037110113081057
>              Type: Hard Disk
>              Capacity: 967.6 MB = 0.9 GB (1981728 x 512)
> USB0:   USB EHCI 1.00
> scanning bus 0 for devices... 1 USB Device(s) found
> Type the command 'usb start' to scan for USB storage devices.
>
>
> Any hint is appreciated.
>
> Thanks,
> Yang
>

[toc] | [next] | [standalone]

#1338612

On 2/19/2016 5:15 PM, David Daney wrote:
> On 02/19/2016 05:12 PM, Yang Shi wrote:
>> Hi David,
>>
>> I tried to boot 4.5-rc4 kernel on my CN6880 board, but it is failed at
>> booting up secondary cores. The error is:
>
> Have you had luck with any other kernel.org versions?

Not tried yet. I will try to bisect it.

>
> FWIW, I recently posed some patches that may help.  I haven't recently 
> tested on cn68xx though, so I can't really say what it might be.

Do you mean the change in CN78xx support patchset?

Thanks,
Yang

>
>
>>
>> CPU31 revision is: 000d9101 (Cavium Octeon II)
>> SMP: Booting CPU32 (CoreId 32)...
>> Secondary boot timeout
>>
>> I passed "numcores=32" in kernel commandline since there are 32 cores
>> ion CN6880. And, the bootloader information is as below:
>>
>> U-Boot 2013.07 ( (U-BOOT build: 104, SDK version: 3.1.1-544),
>> svnversion: u-boot:107133M, exec:)-svn107117 (Build time: Oct 31 2014 -
>> 19:39:37)
>>
>> Skipping PCIe port 0 BIST, reset not done. (port not configured)
>> Skipping PCIe port 1 BIST, reset not done. (port not configured)
>> BIST check passed.
>> EBB6800 board revision major:2, minor:0, serial #: 2011-2.0-00120
>> OCTEON CN6880-AAP pass 1.1, Core clock: 1200 MHz, IO clock: 800 MHz, DDR
>> clock: 667 MHz (1334 Mhz DDR)
>> Base DRAM address used by u-boot: 0x20f000000, size: 0x1000000
>> DRAM: 8 GiB
>> Clearing DRAM...... done
>> NAND:  4096 MiB
>> Registered IDE device 0 from IDE bus:dev 0:0
>> Flash: 8 MiB
>> 0:PCIe: Port 0 is unknown, skipping.
>> 0:PCIe: Port 1 is unknown, skipping.
>> PCI console init succeeded, 1 consoles, 1024 bytes each
>> Net:   octmgmt0, octeth0, octeth1, octeth2, octeth3
>> Bus 0: OK
>>    Device 0: Model: CF 1GB Firm: 20071116 Ser#: TSS20037110113081057
>>              Type: Hard Disk
>>              Capacity: 967.6 MB = 0.9 GB (1981728 x 512)
>> USB0:   USB EHCI 1.00
>> scanning bus 0 for devices... 1 USB Device(s) found
>> Type the command 'usb start' to scan for USB storage devices.
>>
>>
>> Any hint is appreciated.
>>
>> Thanks,
>> Yang
>>
>
>

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web