Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1323942 > unrolled thread

[PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  [PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators Chen-Yu Tsai <wens@csie.org> - 2016-02-02 11:30 +0100

#1323942 — [PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 121 +++++++++++++++++++++++++++-
 1 file changed, 119 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index eb2ccd0a3bd5..4d56dc69713c 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -98,7 +98,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
 	cd-inverted;
@@ -108,7 +108,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -126,6 +126,123 @@
 
 &r_rsb {
 	status = "okay";
+
+	axp809: pmic@3a3 {
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp809.dtsi"
+
+&reg_aldo1 {
+	/* TODO: This should be handled by the USB PHY driver */
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc33-usbh";
+};
+
+&reg_aldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pb-io-cam";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus-09-usbh";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc4 {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys-usb0-hdmi";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1425000>;
+	regulator-max-microvolt = <1575000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+	/*
+	 * The WiFi chip supports a wide range (3.0 ~ 4.8V) of voltages,
+	 * and so does this regulator (3.0 ~ 4.2V), but Allwinner SDK
+	 * always sets it to 3.3V.
+	 */
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dvdd-cam";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_eldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pm-codec-io1";
+};
+
+&reg_ldo_io0 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pg";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pa-gmac-2v5";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc-vdd1v8-io";
 };
 
 &uart0 {
-- 
2.7.0

[toc] | [standalone]

Back to top | Article view | linux.kernel

csiph-web