[PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators

From	Chen-Yu Tsai <wens@csie.org>
Newsgroups	linux.kernel
Subject	[PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators
Date	2016-02-02 11:30 +0100
Message-ID	<qXGnD-1ad-1@gated-at.bofh.it> (permalink)
References	<qXGnD-1ad-3@gated-at.bofh.it>
Organization	linux.* mail to news gateway

Show all headers | View raw

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 121 +++++++++++++++++++++++++++-
 1 file changed, 119 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index eb2ccd0a3bd5..4d56dc69713c 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -98,7 +98,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
 	cd-inverted;
@@ -108,7 +108,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -126,6 +126,123 @@
 
 &r_rsb {
 	status = "okay";
+
+	axp809: pmic@3a3 {
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp809.dtsi"
+
+&reg_aldo1 {
+	/* TODO: This should be handled by the USB PHY driver */
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc33-usbh";
+};
+
+&reg_aldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pb-io-cam";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus-09-usbh";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc4 {
+	regulator-always-on;
+	regulator-min-microvolt = <800000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys-usb0-hdmi";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1425000>;
+	regulator-max-microvolt = <1575000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+	/*
+	 * The WiFi chip supports a wide range (3.0 ~ 4.8V) of voltages,
+	 * and so does this regulator (3.0 ~ 4.2V), but Allwinner SDK
+	 * always sets it to 3.3V.
+	 */
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dvdd-cam";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_eldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pm-codec-io1";
+};
+
+&reg_ldo_io0 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pg";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pa-gmac-2v5";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc-vdd1v8-io";
 };
 
 &uart0 {
-- 
2.7.0

Back to linux.kernel | Previous | Next | Find similar | Unroll thread

Thread

[PATCH 09/11] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators Chen-Yu Tsai <wens@csie.org> - 2016-02-02 11:30 +0100

csiph-web