Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler

From	Moritz Fischer <moritz.fischer.private@gmail.com>
Newsgroups	linux.kernel
Subject	Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler
Date	2017-03-13 17:20 +0100
Message-ID	<tkARs-34n-41@gated-at.bofh.it> (permalink)
References	<tjAqu-1kb-19@gated-at.bofh.it> <tjAqu-1kb-17@gated-at.bofh.it> <tjBwd-1Z5-13@gated-at.bofh.it> <tkARs-34n-43@gated-at.bofh.it>
Organization	linux.* mail to news gateway

Show all headers | View raw

On Mon, Mar 13, 2017 at 3:27 AM, Michal Simek <michal.simek@xilinx.com> wrote:
> Hi Moritz,
>
> On 10.3.2017 23:42, Moritz Fischer wrote:
>> On Fri, Mar 10, 2017 at 1:30 PM, Moritz Fischer <mdf@kernel.org> wrote:
>>> This adds support for the Xilinx LogiCORE PR Decoupler
>>> soft-ip that does decoupling of PR regions in the FPGA
>>> fabric during partial reconfiguration.
>>>
>>> Signed-off-by: Moritz Fischer <mdf@kernel.org>
>>> Cc: Michal Simek <michal.simek@xilinx.com>
>>> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
>>> Cc: linux-kernel@vger.kernel.org
>>> Cc: devicetree@vger.kernel.org
>>> ---
>>>  drivers/fpga/Kconfig               |   9 +++
>>>  drivers/fpga/Makefile              |   1 +
>>>  drivers/fpga/xilinx-pr-decoupler.c | 156 +++++++++++++++++++++++++++++++++++++
>>>  3 files changed, 166 insertions(+)
>>>  create mode 100644 drivers/fpga/xilinx-pr-decoupler.c
>
> I have written very similar driver some week ago but didn't sent it out.

Hah. I'll take a look.

> Here it is.
> https://github.com/Xilinx/linux-xlnx/blob/master/drivers/fpga/xilinx-pr-decoupler.c
>
> Your clk handling is better and my enable_show is better.
> You shouldn't rely on setting status before. It is better to read that
> reg again. The reason is you can connect status signal from one PR
> decoupler to decouple input which can change status

I will just merge them together and add you to author's list if that's
fine with you?

> There is another topic I wanted to open in connection to this. There
> should be gpio based bridge because this pr decoupler can be without axi
> interface and for that gpio driver would be useful.

That's a good idea. I can look at that. This can be pretty generic
code I suppose.

Cheers,

Moritz

Back to linux.kernel | Previous | Next — Previous in thread | Find similar | Unroll thread

Thread

[PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler Moritz Fischer <mdf@kernel.org> - 2017-03-10 22:40 +0100
  Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler Moritz Fischer <mdf@kernel.org> - 2017-03-10 23:50 +0100
    Re: [PATCH 2/2] fpga: Add support for Xilinx LogiCORE PR Decoupler Moritz Fischer <moritz.fischer.private@gmail.com> - 2017-03-13 17:20 +0100

csiph-web