Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1652317

Re: [PATCH 1/2] dt-bindings: reset: Add bindings for basic reset controller

Show all headers | View raw

Hi Joel,

On Fri, 2017-05-26 at 13:32 +1000, Joel Stanley wrote:
> This adds the bindings documentation for a basic single-register reset
> controller.
> 
> The bindings describe a single 32-bit register that contains up to 32
> reset lines, each deasserted by clearing the appropriate bit in the
> register.
>
> Signed-off-by: Joel Stanley <joel@jms.id.au>
> ---
>  .../devicetree/bindings/reset/reset-basic.txt      | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/reset/reset-basic.txt
> 
> diff --git a/Documentation/devicetree/bindings/reset/reset-basic.txt b/Documentation/devicetree/bindings/reset/reset-basic.txt
> new file mode 100644
> index 000000000000..7341e04e7904
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/reset/reset-basic.txt
> @@ -0,0 +1,31 @@
> +Basic single-register reset controller
> +======================================
> +
> +This describes a generic reset controller where the reset lines are controlled
> +by single bits within a 32-bit memory location. The memory location is assumed
> +to be part of a syscon regmap.

There are a few more assumptions. First, that the reset line is asserted
by setting the corresponding bits, and that it is deasserted by clearing
them. Further, that the bits are not auto-clearing. And then, that the
same bit can be read back to provide the current reset line status.

> +Reset controller required properties:
> + - compatible: should be "reset-basic"
> + - #reset-cells: must be set to 1
> + - reg: reset register location within regmap
> +
> +Device node required properties:
> + - resets phandle
> + - bit number, counting from zero, for the desired reset line. Max is 31.
> +
> +Example:
> +
> +syscon {
> +	compatible = "syscon";
> +
> +	uart_rest: rest@0c {

The device node name should be "reset-controller", and leading zeroes
should be dropped from the address part:

	uart_rest: reset-controller@c {

> +		compatible = "reset-basic";

Maybe this is not necessary for the example, but the compatible should
contain a vendor/hardware specific string first.

> +		#reset-cells = <1>;
> +		reg = <0x0c>;
> +	};
> +}
> +
> +&uart {
> +	resets = <&uart_rest 0x04>;

I'd use decimal here.

regards
Philipp

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

[PATCH 0/2] reset: Basic reset controller Joel Stanley <joel@jms.id.au> - 2017-05-26 05:40 +0200
  [PATCH 1/2] dt-bindings: reset: Add bindings for basic reset controller Joel Stanley <joel@jms.id.au> - 2017-05-26 05:40 +0200
    Re: [PATCH 1/2] dt-bindings: reset: Add bindings for basic reset  controller Philipp Zabel <p.zabel@pengutronix.de> - 2017-05-29 11:10 +0200
      Re: [PATCH 1/2] dt-bindings: reset: Add bindings for basic reset controller Joel Stanley <joel@jms.id.au> - 2017-05-29 12:20 +0200
  [PATCH 2/2] reset: Add basic single-register reset driver Joel Stanley <joel@jms.id.au> - 2017-05-26 05:40 +0200
    Re: [PATCH 2/2] reset: Add basic single-register reset driver Andy Shevchenko <andy.shevchenko@gmail.com> - 2017-05-27 17:20 +0200
      Re: [PATCH 2/2] reset: Add basic single-register reset driver Joel Stanley <joel@jms.id.au> - 2017-05-29 12:30 +0200
        Re: [PATCH 2/2] reset: Add basic single-register reset driver Andy Shevchenko <andy.shevchenko@gmail.com> - 2017-05-29 17:50 +0200

csiph-web