Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1494574

Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR interrupts

Show all headers | View raw

Den 29.09.2016 07:37, skrev Stefan Wahren:
>> Noralf Trønnes <noralf@tronnes.org> hat am 29. September 2016 um 00:22
>> geschrieben:
>>
>>
>>
>> Den 29.09.2016 00:00, skrev Eric Anholt:
>>> Noralf Trønnes <noralf@tronnes.org> writes:
>>>
>>>> If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
>>>> the driver has no way to fill/drain the FIFO to stop the interrupts.
>>>> In this case the controller has to be disabled and the transfer
>>>> completed to avoid hang.
>>>>
>>>> (CLKT | ERR) and DONE interrupts are completed in their own paths, and
>>>> the controller is disabled in the transfer function after completion.
>>>> Unite the code paths and do disabling inside the interrupt routine.
>>>>
>>>> Clear interrupt status bits in the united completion path instead of
>>>> trying to do it on every interrupt which isn't necessary.
>>>> Only CLKT, ERR and DONE can be cleared that way.
>>>>
>>>> Add the status value to the error value in case of TXW/RXR errors to
>>>> distinguish them from the other S_LEN error.
>>> I was surprised that not writing the TXW/RXR bits on handling their
>>> interrupts was OK, given that we were doing so before, but it's a level
>>> interrupt and those bits are basically ignored on write.
>>>
>>> This patch and 3, 4, and 6 are:
>>>
>>> Reviewed-by: Eric Anholt <eric@anholt.net>
>>>
>>> Patch 5 is:
>>>
>>> Acked-by: Eric Anholt <eric@anholt.net>
>>>
>>> Note for future debug: The I2C_C_CLEAR on errors will take some time to
>>> resolve -- if you were in non-idle state and I2C_C_READ, it sets an
>>> abort_rx flag and runs through the state machine to send a NACK and a
>>> STOP, I think.  Since we're setting CLEAR without I2CEN, that NACK will
>>> be hanging around queued up for next time we start the engine.
>> Maybe you're able to explain the issues I had with reset:
>> https://github.com/raspberrypi/linux/issues/1653
>>
>> Should we put your note into the commit message?
>> It will most likely be lost if it just stays in this email.
> I prefer to have this kind of information as a code comment.

Eric, does this look good to you as a code comment:

/*
  * Note about I2C_C_CLEAR on error:
  * The I2C_C_CLEAR on errors will take some time to resolve -- if you 
were in
  * non-idle state and I2C_C_READ, it sets an abort_rx flag and runs through
  * the state machine to send a NACK and a STOP. Since we're setting CLEAR
  * without I2CEN, that NACK will be hanging around queued up for next time
  * we start the engine.
  */


If it is, I'll resend the series with this change and add all the ack's 
and r-b's.

Noralf.

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

[PATCH v3 0/7] i2c: bcm2835: Bring in changes from downstream Noralf Trønnes <noralf@tronnes.org> - 2016-09-28 20:00 +0200
  [PATCH v3 5/7] i2c: bcm2835: Add support for Repeated Start Condition Noralf Trønnes <noralf@tronnes.org> - 2016-09-28 20:00 +0200
  [PATCH v3 7/7] i2c: bcm2835: Add support for dynamic clock Noralf Trønnes <noralf@tronnes.org> - 2016-09-28 20:00 +0200
    Re: [PATCH v3 7/7] i2c: bcm2835: Add support for dynamic clock Eric Anholt <eric@anholt.net> - 2016-09-28 23:30 +0200
      Re: [PATCH v3 7/7] i2c: bcm2835: Add support for dynamic clock Noralf Trønnes <noralf@tronnes.org> - 2016-09-29 00:20 +0200
      Re: [PATCH v3 7/7] i2c: bcm2835: Add support for dynamic clock Martin Sperl <kernel@martin.sperl.org> - 2016-09-29 10:10 +0200
  [PATCH v3 6/7] i2c: bcm2835: Support i2c-dev ioctl I2C_TIMEOUT Noralf Trønnes <noralf@tronnes.org> - 2016-09-28 20:00 +0200
  [PATCH v3 1/7] i2c: bcm2835: Fix hang for writing messages larger than 16 bytes Noralf Trønnes <noralf@tronnes.org> - 2016-09-28 20:00 +0200
  [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR interrupts Noralf Trønnes <noralf@tronnes.org> - 2016-09-28 20:00 +0200
    Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR interrupts Eric Anholt <eric@anholt.net> - 2016-09-29 00:10 +0200
      Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR  interrupts Noralf Trønnes <noralf@tronnes.org> - 2016-09-29 00:30 +0200
        Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR  interrupts Stefan Wahren <stefan.wahren@i2se.com> - 2016-09-29 07:40 +0200
          Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR  interrupts Noralf Trønnes <noralf@tronnes.org> - 2016-10-02 16:30 +0200
            Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR interrupts Eric Anholt <eric@anholt.net> - 2016-10-03 21:00 +0200
        Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR interrupts Eric Anholt <eric@anholt.net> - 2016-10-03 21:50 +0200
          Re: [PATCH v3 2/7] i2c: bcm2835: Protect against unexpected TXW/RXR  interrupts Noralf Trønnes <noralf@tronnes.org> - 2016-10-04 21:30 +0200

csiph-web