Groups | Search | Server Info | Login | Register

Groups > nl.comp.os.linux.techniek > #9653

Re: Data redden

Show all headers | View raw

Op 02-07-2024 om 02:33 schreef Adri Verhoef:
> Op moederschip aarde schreef iemand die zich identificeerde als
> De ongekruisigde (ds.) <deongekruisigde@invalid.invalid>:
>> On 2024-06-29, Paul van der Vlis <paul@vandervlis.nl> wrote:
>>> Hoi,
>>>
>>> Ik probeer de data te redden van een USB-disk. De vorige twee keer ging
>>> dat goed. Maar hier verschijnt /dev/sdd alleen tijdelijk even tijdens
>>> het starten, maar is al vrij snel weer verdwenen.
>>>
>>> Ik heb twee verschillende computers en kabels geprobeerd.
>>> Zie onder output van dmesg.
>>>
>>> Heeft iemand nog ideeën wat ik zou kunnen doen om /dev/sdd te laten
>>> voortbestaan, zodat ik de data eraf kan halen?
>>
>> Als ik die log lees dan lijkt het ding gewoon kapot (elektronisch
>> of zo). Waarschijnlijk helaas voor de data erop.
>>
>>
>>> Groet,
>>> Paul
>>>
>>>
>>> 174264.957546] usb 1-1.5: new high-speed USB device number 23 using ehci-pci
>>> [174265.107849] usb 1-1.5: New USB device found, idVendor=1058,
>>> idProduct=2620, bcdDevice=10.23
>>> [174265.107853] usb 1-1.5: New USB device strings: Mfr=2, Product=3,
>>> SerialNumber=1
>>> [174265.107855] usb 1-1.5: Product: Elements 2620
>>> [174265.107856] usb 1-1.5: Manufacturer: Western Digital
>>> [174265.107858] usb 1-1.5: SerialNumber: 57583732443631304B365431
>>> [174265.108279] usb-storage 1-1.5:1.0: USB Mass Storage device detected
>>> [174265.108658] scsi host7: usb-storage 1-1.5:1.0
>>> [174266.118725] scsi 7:0:0:0: Direct-Access     WD       Elements 2620
>>>    1023 PQ: 0 ANSI: 6
>>> [174266.119767] sd 7:0:0:0: Attached scsi generic sg4 type 0
>>> [174266.123256] sd 7:0:0:0: [sdd] Spinning up disk...
>>> [174267.141475]
>>> .........................................................ready
>>> [174324.485251] sd 7:0:0:0: [sdd] Very big device. Trying to use READ
>>> CAPACITY(16).
>>> [174324.485882] sd 7:0:0:0: [sdd] 9767475200 512-byte logical blocks:
>>> (5.00 TB/4.55 TiB)
>>> [174324.485885] sd 7:0:0:0: [sdd] 4096-byte physical blocks
>>> [174324.487263] sd 7:0:0:0: [sdd] Write Protect is off
>>> [174324.487268] sd 7:0:0:0: [sdd] Mode Sense: 47 00 10 08
>>> [174324.488713] sd 7:0:0:0: [sdd] No Caching mode page found
>>> [174324.488721] sd 7:0:0:0: [sdd] Assuming drive cache: write through
>>> [174355.583306] usb 1-1.5: reset high-speed USB device number 23 using
>>> ehci-pci
>>> [174360.691216] usb 1-1.5: device descriptor read/64, error -110
>>> [174376.306788] usb 1-1.5: device descriptor read/64, error -110
>>> [174376.494792] usb 1-1.5: reset high-speed USB device number 23 using
>>> ehci-pci
>>> [174381.682674] usb 1-1.5: device descriptor read/64, error -110
>>> [174397.306284] usb 1-1.5: device descriptor read/64, error -110
>>> [174397.494297] usb 1-1.5: reset high-speed USB device number 23 using
>>> ehci-pci
> 
> https://askubuntu.com/questions/644010/ubuntu-cant-read-my-usb-device-descriptor-read-64-error-110
> "The device descriptor read/64, error -110 means that USB port power supply was
> exceeded."
> https://stackoverflow.com/questions/13653692/device-descriptor-read-64-error-110
> "USB error -110 means "Timeout expired before the transfer completed", which
> could be caused by anything. Most commonly, it's because power was exceeded;
> the host could not provide enough electric power for the pendrive to operate.
> Because it has not enough power also the USB stick cannot provide the device
> descriptor to the host, as a result it cannot be identified and so on. Maybe
> your motherboard it's overloaded with devices that consume all the available
> power."
> "I had the same error, but with no USB device plugged in. I have a Suse 13.2
> and 42.2 installed on an internal ssd drive in a HP ProBook 430. When I booted
> into 42.2, I got that error and booting simply stopped there. Weird enough with
> 13.2 on the same hard disk I could boot with no problems. Following Johnsters
> advice to unplug any power supply including battery removal finally did it, so
> loads of thanks go there. And to all running into this post without any obvious
> interaction of USB devices in their problems: Try making your system voltage
> free, it still might do the trick."
> "Main voltage is not high enough in my home. It's below 180V (normally
> 220-240). Sometimes I get the same error. Sometimes my PC restarts itself."
> 
> Ik realiseer me dat dit niet per se de oplossing voor jouw probleem is, Paul,
> het zijn slechts suggesties; misschien brengen ze je op ideeën om het probleem
> aan te pakken.

Bedankt, ik ga hiernaar kijken...

Groet,
Paul


-- 
Paul van der Vlis Linux systeembeheer Groningen
https://vandervlis.nl

Back to nl.comp.os.linux.techniek | Previous | Next — Previous in thread | Next in thread | Find similar

Thread

Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-06-29 17:11 +0200
  Re: Data redden "De ongekruisigde (ds.)" <ongekruisigde@gekruisigden.invalid> - 2024-06-29 17:08 +0000
    Re: Data redden a3@a3.nl.invalid (Adri Verhoef) - 2024-07-02 00:33 +0000
      Re: Data redden Ozymandias <ozymandias@ozymandias.invalid> - 2024-07-02 08:20 +0000
      Re: Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-07-03 13:01 +0200
        Re: Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-07-03 13:41 +0200
          Re: Data redden Ozymandias <ozymandias@ozymandias.invalid> - 2024-07-03 12:29 +0000
      Re: Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-07-03 13:58 +0200
        Re: Data redden a3@a3.nl.invalid (Adri Verhoef) - 2024-07-15 00:00 +0000

csiph-web