Groups | Search | Server Info | Login | Register

Groups > nl.comp.os.linux.techniek > #9648

Re: Data redden

Show all headers | View raw

Op moederschip aarde schreef iemand die zich identificeerde als
De ongekruisigde (ds.) <deongekruisigde@invalid.invalid>:
>On 2024-06-29, Paul van der Vlis <paul@vandervlis.nl> wrote:
>> Hoi,
>>
>> Ik probeer de data te redden van een USB-disk. De vorige twee keer ging 
>> dat goed. Maar hier verschijnt /dev/sdd alleen tijdelijk even tijdens 
>> het starten, maar is al vrij snel weer verdwenen.
>>
>> Ik heb twee verschillende computers en kabels geprobeerd.
>> Zie onder output van dmesg.
>>
>> Heeft iemand nog ideeën wat ik zou kunnen doen om /dev/sdd te laten 
>> voortbestaan, zodat ik de data eraf kan halen?
>
>Als ik die log lees dan lijkt het ding gewoon kapot (elektronisch
>of zo). Waarschijnlijk helaas voor de data erop.
>
>
>> Groet,
>> Paul
>>
>>
>> 174264.957546] usb 1-1.5: new high-speed USB device number 23 using ehci-pci
>> [174265.107849] usb 1-1.5: New USB device found, idVendor=1058, 
>> idProduct=2620, bcdDevice=10.23
>> [174265.107853] usb 1-1.5: New USB device strings: Mfr=2, Product=3, 
>> SerialNumber=1
>> [174265.107855] usb 1-1.5: Product: Elements 2620
>> [174265.107856] usb 1-1.5: Manufacturer: Western Digital
>> [174265.107858] usb 1-1.5: SerialNumber: 57583732443631304B365431
>> [174265.108279] usb-storage 1-1.5:1.0: USB Mass Storage device detected
>> [174265.108658] scsi host7: usb-storage 1-1.5:1.0
>> [174266.118725] scsi 7:0:0:0: Direct-Access     WD       Elements 2620 
>>   1023 PQ: 0 ANSI: 6
>> [174266.119767] sd 7:0:0:0: Attached scsi generic sg4 type 0
>> [174266.123256] sd 7:0:0:0: [sdd] Spinning up disk...
>> [174267.141475] 
>> .........................................................ready
>> [174324.485251] sd 7:0:0:0: [sdd] Very big device. Trying to use READ 
>> CAPACITY(16).
>> [174324.485882] sd 7:0:0:0: [sdd] 9767475200 512-byte logical blocks: 
>> (5.00 TB/4.55 TiB)
>> [174324.485885] sd 7:0:0:0: [sdd] 4096-byte physical blocks
>> [174324.487263] sd 7:0:0:0: [sdd] Write Protect is off
>> [174324.487268] sd 7:0:0:0: [sdd] Mode Sense: 47 00 10 08
>> [174324.488713] sd 7:0:0:0: [sdd] No Caching mode page found
>> [174324.488721] sd 7:0:0:0: [sdd] Assuming drive cache: write through
>> [174355.583306] usb 1-1.5: reset high-speed USB device number 23 using 
>> ehci-pci
>> [174360.691216] usb 1-1.5: device descriptor read/64, error -110
>> [174376.306788] usb 1-1.5: device descriptor read/64, error -110
>> [174376.494792] usb 1-1.5: reset high-speed USB device number 23 using 
>> ehci-pci
>> [174381.682674] usb 1-1.5: device descriptor read/64, error -110
>> [174397.306284] usb 1-1.5: device descriptor read/64, error -110
>> [174397.494297] usb 1-1.5: reset high-speed USB device number 23 using 
>> ehci-pci

https://askubuntu.com/questions/644010/ubuntu-cant-read-my-usb-device-descriptor-read-64-error-110
"The device descriptor read/64, error -110 means that USB port power supply was
exceeded."
https://stackoverflow.com/questions/13653692/device-descriptor-read-64-error-110
"USB error -110 means "Timeout expired before the transfer completed", which
could be caused by anything. Most commonly, it's because power was exceeded;
the host could not provide enough electric power for the pendrive to operate.
Because it has not enough power also the USB stick cannot provide the device
descriptor to the host, as a result it cannot be identified and so on. Maybe
your motherboard it's overloaded with devices that consume all the available
power."
"I had the same error, but with no USB device plugged in. I have a Suse 13.2
and 42.2 installed on an internal ssd drive in a HP ProBook 430. When I booted
into 42.2, I got that error and booting simply stopped there. Weird enough with
13.2 on the same hard disk I could boot with no problems. Following Johnsters
advice to unplug any power supply including battery removal finally did it, so
loads of thanks go there. And to all running into this post without any obvious
interaction of USB devices in their problems: Try making your system voltage
free, it still might do the trick."
"Main voltage is not high enough in my home. It's below 180V (normally
220-240). Sometimes I get the same error. Sometimes my PC restarts itself."

Ik realiseer me dat dit niet per se de oplossing voor jouw probleem is, Paul,
het zijn slechts suggesties; misschien brengen ze je op ideeën om het probleem
aan te pakken.

Back to nl.comp.os.linux.techniek | Previous | Next — Previous in thread | Next in thread | Find similar

Thread

Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-06-29 17:11 +0200
  Re: Data redden "De ongekruisigde (ds.)" <ongekruisigde@gekruisigden.invalid> - 2024-06-29 17:08 +0000
    Re: Data redden a3@a3.nl.invalid (Adri Verhoef) - 2024-07-02 00:33 +0000
      Re: Data redden Ozymandias <ozymandias@ozymandias.invalid> - 2024-07-02 08:20 +0000
      Re: Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-07-03 13:01 +0200
        Re: Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-07-03 13:41 +0200
          Re: Data redden Ozymandias <ozymandias@ozymandias.invalid> - 2024-07-03 12:29 +0000
      Re: Data redden Paul van der Vlis <paul@vandervlis.nl> - 2024-07-03 13:58 +0200
        Re: Data redden a3@a3.nl.invalid (Adri Verhoef) - 2024-07-15 00:00 +0000

csiph-web