Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1554827

Re: [PATCH v2 1/6] mmc: sunxi: Always set signal delay to 0 for A64

Show all headers | View raw

On 09/01/17 16:46, Maxime Ripard wrote:
> Experience have shown that the using the  autocalibration could severely
> degrade the performances of the MMC bus.
> 
> Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
> Remove the calibration code for now, and add comments to document our
> findings.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---
>  drivers/mmc/host/sunxi-mmc.c | 50 ++++++++++++-------------------------
>  1 file changed, 17 insertions(+), 33 deletions(-)
> 
> diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
> index b1d1303389a7..ea9552a0d820 100644
> --- a/drivers/mmc/host/sunxi-mmc.c
> +++ b/drivers/mmc/host/sunxi-mmc.c
> @@ -683,41 +683,19 @@ static int sunxi_mmc_oclk_onoff(struct sunxi_mmc_host *host, u32 oclk_en)
>  
>  static int sunxi_mmc_calibrate(struct sunxi_mmc_host *host, int reg_off)
>  {
> -	u32 reg = readl(host->reg_base + reg_off);
> -	u32 delay;
> -	unsigned long timeout;
> -
>  	if (!host->cfg->can_calibrate)
>  		return 0;
>  
> -	reg &= ~(SDXC_CAL_DL_MASK << SDXC_CAL_DL_SW_SHIFT);
> -	reg &= ~SDXC_CAL_DL_SW_EN;
> -
> -	writel(reg | SDXC_CAL_START, host->reg_base + reg_off);
> -
> -	dev_dbg(mmc_dev(host->mmc), "calibration started\n");
> -
> -	timeout = jiffies + HZ * SDXC_CAL_TIMEOUT;
> -
> -	while (!((reg = readl(host->reg_base + reg_off)) & SDXC_CAL_DONE)) {
> -		if (time_before(jiffies, timeout))
> -			cpu_relax();
> -		else {
> -			reg &= ~SDXC_CAL_START;
> -			writel(reg, host->reg_base + reg_off);
> -
> -			return -ETIMEDOUT;
> -		}
> -	}
> -
> -	delay = (reg >> SDXC_CAL_DL_SHIFT) & SDXC_CAL_DL_MASK;
> -
> -	reg &= ~SDXC_CAL_START;
> -	reg |= (delay << SDXC_CAL_DL_SW_SHIFT) | SDXC_CAL_DL_SW_EN;
> -
> -	writel(reg, host->reg_base + reg_off);
> -
> -	dev_dbg(mmc_dev(host->mmc), "calibration ended, reg is 0x%x\n", reg);
> +	/*
> +	 * FIXME:
> +	 * This is not clear how the calibration is supposed to work
> +	 * yet. The best rate have been obtained by simply setting the
> +	 * delay to 0, as Allwinner does in its BSP.
> +	 *
> +	 * The only mode that doesn't have such a delay is HS400, that
> +	 * is in itself a TODO.
> +	 */
> +	writel(SDXC_CAL_DL_SW_EN, host->reg_base + reg_off);
>  
>  	return 0;
>  }
> @@ -806,7 +784,13 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host,
>  	if (ret)
>  		return ret;
>  
> -	/* TODO: enable calibrate on sdc2 SDXC_REG_DS_DL_REG of A64 */
> +	/*
> +	 * FIXME:
> +	 *
> +	 * In HS400 we'll also need to calibrate the data strobe
> +	 * signal. This should only happen on the MMC2 controller (at
> +	 * least on the A64 and older SoCs).

Which older SoCs have this calibration register and a DS signal?
Is that supposed to mean "other" SoCs?

Other than that:

Reviewed-by: Andre Przywara <andre.przywara@arm.com>

Cheers,
Andre.

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

[PATCH v2 1/6] mmc: sunxi: Always set signal delay to 0 for A64 Maxime Ripard <maxime.ripard@free-electrons.com> - 2017-01-09 17:50 +0100
  Re: [PATCH v2 1/6] mmc: sunxi: Always set signal delay to 0 for A64 André Przywara <andre.przywara@arm.com> - 2017-01-10 01:40 +0100
    Re: [PATCH v2 1/6] mmc: sunxi: Always set signal delay to 0 for A64 Maxime Ripard <maxime.ripard@free-electrons.com> - 2017-01-11 22:20 +0100

csiph-web