Re: Group Design

From	Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>
Newsgroups	comp.arch.embedded
Subject	Re: Group Design
Date	2020-08-06 23:39 -0400
Organization	A noiseless patient Spider
Message-ID	<18abe082-c8e1-203f-c8d2-da862acf9523@electrooptical.net> (permalink)
References	(7 earlier) <rgi24o$1has$1@gioia.aioe.org> <cc6f131d-e8e7-387a-fe5e-907478e75062@electrooptical.net> <26158b23-01ea-4164-a847-2032f7b23f78o@googlegroups.com> <09585e89-a7f3-8fb1-42b9-96e3f6f6599a@electrooptical.net> <255a2432-bba9-4dbd-9ae8-6b86745e6035o@googlegroups.com>

Show all headers | View raw

On 2020-08-06 22:36, Rick C wrote:
> On Thursday, August 6, 2020 at 10:27:27 PM UTC-4, Phil Hobbs wrote:
>> On 2020-08-06 22:12, Rick C wrote:
>>> On Thursday, August 6, 2020 at 9:50:24 PM UTC-4, Phil Hobbs
>>> wrote:
>>>> On 2020-08-06 19:01, Chris wrote:
>>>>> On 07/08/20 23:20, Rick C wrote:
>>>>> 
>>>>>> I'm also concerned about the board layout.  The board is
>>>>>> not at all dense but there are several
>>>>> 
>>>>> parts that need copper area for heat sinking.  They are using
>>>>> a linear regulator to drop 12+ volts
>>>>> 
>>>>> to 5V and 3.3V.  The back lights for the LCDs draw 300 mA!
>>>>> So the 5V regulator gets quite warm,
>>>>> 
>>>>> 70°C!!!
>>>>> 
>>>>> You should be concerned. The whole thing about safety
>>>>> critical kit is that it should be conservatively designed,
>>>>> with all parts running well within their ratings. If the hw
>>>>> bod is happy with a regulator running at 70c, he must be
>>>>> clueless. Sorry, but it needs to be said.
>>>>> 
>>>>> If you care about your professional career and any
>>>>> litigation issues, you should either have enough influence on
>>>>> the project direction to stop design errors like that, or
>>>>> just walk away from it...
>>>>> 
>>>>> Chris
>>>> 
>>>> Hmm, interesting.  Most linear regulators I'm familiar with are
>>>> rated to 125 C junction temperature, and some higher.  What
>>>> safety or regulatory issues have you run into that were caused
>>>> by running some part 55C below its rated temperature?
>>> 
>>> That was the case temp via an IR gun.  So the die was hotter.  I
>>> would not approve a design with a part running so hot.  I believe
>>> the failure rate goes up quite quickly with temp.  The real point
>>> is this is because the layout was not correct using thermal
>>> breaks around the thermal pad!!!  Easy enough to fix lowering the
>>> temp probably by 30 °C.
>>> 
>>> Did you not read the original post about this?
>>> 
>> 
>> I've designed a fair bit of stuff to work in ambients higher than
>> that, from remote satcom stuff to downhole instruments running at
>> 175C.
> 
> So???  Higher temps means shorter life.  Is that a false statement?
> 
> There is also the issue of heating up things adjacent to the hot part
> and at 70 °C there is risk of burning someone not used to board
> getting that hot.
> 
> In other words, there is no reason to have such an abortion for a
> design that it gets so hot.  Why is this an issue for you?  You are
> not making any sense at all.

Okay, so you've got zilch.  No worries.

Cheers

Phil Hobbs


-- 
Dr Philip C D Hobbs
Principal Consultant
ElectroOptical Innovations LLC / Hobbs ElectroOptics
Optics, Electro-optics, Photonics, Analog Electronics
Briarcliff Manor NY 10510

http://electrooptical.net
http://hobbs-eo.com

Thread

Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-07 18:46 -0700
  Re: Group Design Paul Rubin <no.email@nospam.invalid> - 2020-07-07 19:02 -0700
    Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-07 20:36 -0700
      Re: Group Design David Brown <david.brown@hesbynett.no> - 2020-07-08 09:31 +0200
        Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-08 07:08 -0700
  Re: Group Design Stef <stef33d@yahooI-N-V-A-L-I-D.com.invalid> - 2020-07-08 14:13 +0200
    Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-08 07:19 -0700
      Re: Group Design Stef <stef33d@yahooI-N-V-A-L-I-D.com.invalid> - 2020-07-08 18:57 +0200
        Re: Group Design Theo <theom+news@chiark.greenend.org.uk> - 2020-07-08 18:28 +0100
        Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-08 11:12 -0700
          Re: Group Design Stef <stef33d@yahooI-N-V-A-L-I-D.com.invalid> - 2020-07-08 23:34 +0200
            Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-08 15:20 -0700
              Re: Group Design Paul Rubin <no.email@nospam.invalid> - 2020-07-08 23:00 -0700
              Re: Group Design Stef <stef33d@yahooI-N-V-A-L-I-D.com.invalid> - 2020-07-10 10:09 +0200
              Re: Group Design Chris <xxx.syseng.yyy@gfsys.co.uk> - 2020-08-07 00:01 +0100
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-06 17:37 -0700
                Re: Group Design Paul Rubin <no.email@nospam.invalid> - 2020-08-07 03:06 -0700
                Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-08-06 21:50 -0400
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-06 19:12 -0700
                Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-08-06 22:27 -0400
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-06 19:36 -0700
                Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-08-06 23:39 -0400
                Re: Group Design Chris <xxx.syseng.yyy@gfsys.co.uk> - 2020-08-07 12:30 +0100
                Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-08-07 09:57 -0400
                Re: Group Design Chris <xxx.syseng.yyy@gfsys.co.uk> - 2020-08-08 00:37 +0100
                Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-08-07 20:29 -0400
                Re: Group Design upsidedown@downunder.com - 2020-08-08 08:59 +0300
                Re: Group Design David Brown <david.brown@hesbynett.no> - 2020-08-10 15:43 +0200
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-10 09:18 -0700
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-07 07:12 -0700
                Re: Group Design Chris <xxx.syseng.yyy@gfsys.co.uk> - 2020-08-08 00:00 +0100
                Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-08-07 20:30 -0400
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-07 17:57 -0700
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-07 17:56 -0700
                Re: Group Design Paul Rubin <no.email@nospam.invalid> - 2020-08-07 18:10 -0700
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-07 19:43 -0700
                Re: Group Design Dimiter_Popoff <dp@tgi-sci.com> - 2020-08-07 20:42 +0300
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-08-07 13:48 -0700
      Re: Group Design Paul Rubin <no.email@nospam.invalid> - 2020-07-08 14:11 -0700
      Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-07-09 04:25 -0400
        Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-09 11:37 -0700
          Re: Group Design Paul Rubin <no.email@nospam.invalid> - 2020-07-09 11:54 -0700
          Re: Group Design Tom Gardner <spamjunk@blueyonder.co.uk> - 2020-07-09 20:02 +0100
          Re: Group Design Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> - 2020-07-09 15:31 -0400
            Re: Group Design lasselangwadtchristensen@gmail.com - 2020-07-09 15:36 -0700
              Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-09 18:36 -0700
                Re: Group Design Clifford Heath <no.spam@please.net> - 2020-07-10 16:17 +1000
                Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-09 23:36 -0700
                Re: Group Design Stef <stef33d@yahooI-N-V-A-L-I-D.com.invalid> - 2020-07-10 10:22 +0200
      Re: Group Design David Brown <david.brown@hesbynett.no> - 2020-07-09 14:40 +0200
  Re: Group Design John Speth <johnspeth@yahoo.com> - 2020-07-09 07:59 -0700
  Re: Group Design Don Y <blockedofcourse@foo.invalid> - 2020-07-09 18:33 -0700
    Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-09 19:01 -0700
      Re: Group Design Don Y <blockedofcourse@foo.invalid> - 2020-07-09 22:32 -0700
      Re: Group Design George Neuner <gneuner2@comcast.net> - 2020-07-10 17:36 -0400
        Re: Group Design Ed Prochak <edprochak@gmail.com> - 2020-07-14 11:09 -0700
          Re: Group Design George Neuner <gneuner2@comcast.net> - 2020-07-16 00:26 -0400
  Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-09 22:48 -0700
    Re: Group Design Don Y <blockedofcourse@foo.invalid> - 2020-07-09 23:53 -0700
      Re: Group Design Rick C <gnuarm.deletethisbit@gmail.com> - 2020-07-10 01:15 -0700
        Re: Group Design Don Y <blockedofcourse@foo.invalid> - 2020-07-10 02:22 -0700

csiph-web