Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]
Groups > sci.electronics.design > #447863
| From | Joerg <news@analogconsultants.com> |
|---|---|
| Newsgroups | sci.electronics.design |
| Subject | Re: analog failures |
| Date | 2017-02-16 07:41 -0800 |
| Message-ID | <eglvhdFnd5lU1@mid.individual.net> (permalink) |
| References | (4 earlier) <o80jd1$set$1@dont-email.me> <egjbr9F7dhiU1@mid.individual.net> <o82lpj$r0m$1@dont-email.me> <eglttjFn2btU1@mid.individual.net> <5sgbacp5h1jgs7mv379oa1e78n2i6i64ld@4ax.com> |
On 2017-02-16 07:24, John Larkin wrote: > On Thu, 16 Feb 2017 07:14:03 -0800, Joerg <news@analogconsultants.com> > wrote: > >> On 2017-02-15 14:49, Reinhardt Behm wrote: >>> AT Wednesday 15 February 2017 23:53, Joerg wrote: >>> >>>> On 2017-02-14 19:55, Reinhardt Behm wrote: [...] >>>>> I had the same with a part from Microchip. It has a config bit to >>>>> automatically reset its I2C interface after a timeout period without any >>>>> activity on the bus. This bit is reset after power on. So if the >>>>> interface goes gaga because of a poor POR you never get it working. >>>>> >>>> >>>> Oh-oh. Sounds like they built in a loose cannon for a sledgehammer. >>>> However, a poor POR is something the circuit designer should take care >>>> of. Never trust any on-chip POR/BOR. Ever. >>> >>> Good advice if the chip has no reset pin. :-( >>> >> >> I've had designs where it was like your case and then my reset pin was >> introduced by means of a P-channel in the VCC line. However, than meant >> that the data lines had to be muxed and shut off as well or the chip >> could be supplied through its diode paths. >> >> Only at the client's insistence. I prefer stuff that is more reliable. >> In this case, for example, the LM35. Unfortunely that one needs a >> negative supply if low temperatures have to be measured. > > LM35 is one tricky dude. If you pull its output negative more than a > couple tenths of a volt (or some spike does it for you) it will latch > up. The datasheet recommend a resistor of such value, that just a few tens of uA are flowing. But that is only needed if low temps have to be monitored. > Never power them from more than 5 volts, or it will eventually > latch up. It will oscillate if it sees a capacitive load, like a > cable. > That's to be expected, opamps don't like that either. -- Regards, Joerg http://www.analogconsultants.com/
Back to sci.electronics.design | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread
analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-14 14:47 -0800
Re: analog failures Lasse Langwadt Christensen <langwadt@fonz.dk> - 2017-02-14 15:05 -0800
Re: analog failures Reinhardt Behm <rbehm@hushmail.com> - 2017-02-15 10:52 +0800
Re: analog failures bill.sloman@ieee.org - 2017-02-14 19:00 -0800
Re: analog failures Reinhardt Behm <rbehm@hushmail.com> - 2017-02-15 11:55 +0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-15 07:53 -0800
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-15 08:30 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-15 10:19 -0800
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-15 10:53 -0800
Re: analog failures Lasse Langwadt Christensen <langwadt@fonz.dk> - 2017-02-15 10:58 -0800
Re: analog failures "Tim Williams" <tiwill@seventransistorlabs.com> - 2017-02-15 21:25 -0600
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-15 20:18 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-17 15:44 -0500
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-17 15:30 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 14:05 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-17 17:16 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 14:38 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-17 17:58 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 15:37 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-17 18:51 -0500
Re: analog failures krw@notreal.com - 2017-02-17 20:27 -0500
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-17 17:56 -0800
Re: analog failures "Tim Williams" <tiwill@seventransistorlabs.com> - 2017-02-17 21:03 -0600
Re: analog failures krw@notreal.com - 2017-02-17 22:36 -0500
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-19 00:45 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-19 08:32 -0800
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-21 12:31 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-23 14:57 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-23 12:02 -0800
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-17 17:27 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-17 20:39 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-18 07:41 -0800
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-18 08:04 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-18 08:16 -0800
Re: analog failures Reinhardt Behm <rbehm@hushmail.com> - 2017-02-16 06:49 +0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-16 07:14 -0800
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-16 07:24 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-16 07:41 -0800
Re: analog failures Reinhardt Behm <rbehm@hushmail.com> - 2017-02-17 13:22 +0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 06:58 -0800
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-17 12:26 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 14:03 -0800
Re: analog failures "Tim Williams" <tiwill@seventransistorlabs.com> - 2017-02-17 21:05 -0600
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-18 08:07 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-18 08:20 -0800
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-18 09:20 -0800
Re: analog failures rickman <gnuarm@gmail.com> - 2017-02-19 00:48 -0500
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-21 12:39 -0800
Re: analog failures "Tim Williams" <tiwill@seventransistorlabs.com> - 2017-02-21 22:54 -0600
Re: analog failures krw@notreal.com - 2017-02-17 20:33 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-18 07:37 -0800
Re: analog failures dagmargoodboat@yahoo.com - 2017-02-22 15:45 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-23 10:43 -0800
Re: analog failures krw@notreal.com - 2017-02-23 20:42 -0500
Re: analog failures "Tim Williams" <tiwill@seventransistorlabs.com> - 2017-02-24 03:31 -0600
Re: analog failures grahamholloway@graham65.plus.com - 2017-02-24 06:39 -0800
Re: analog failures Don Kuenz <g@crcomp.net> - 2017-02-24 14:58 +0000
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-25 12:48 -0800
Re: analog failures pcdhobbs@gmail.com - 2017-02-26 04:39 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-26 07:52 -0800
Re: analog failures dagmargoodboat@yahoo.com - 2017-02-24 09:02 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-25 12:44 -0800
Re: analog failures dagmargoodboat@yahoo.com - 2017-02-26 08:29 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-26 09:46 -0800
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-26 10:11 -0800
Re: analog failures krw@notreal.com - 2017-02-26 17:55 -0500
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-26 15:09 -0800
Re: analog failures krw@notreal.com - 2017-02-26 19:30 -0500
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-27 10:37 -0800
Re: analog failures Lasse Langwadt Christensen <langwadt@fonz.dk> - 2017-02-24 09:14 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-25 12:46 -0800
Re: analog failures Klaus Kragelund <klauskvik@hotmail.com> - 2017-02-26 17:44 -0800
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-27 07:51 -0800
Re: analog failures Tauno Voipio <tauno.voipio@notused.fi.invalid> - 2017-02-23 21:36 +0200
Re: analog failures dagmargoodboat@yahoo.com - 2017-02-24 08:38 -0800
Re: analog failures krw@notreal.com - 2017-02-24 20:20 -0500
Re: analog failures kevin93 <kevin@whitedigs.com> - 2017-02-24 17:36 -0800
Re: analog failures Ralph Barone <ralph@invalid.com> - 2017-02-15 03:25 +0000
Re: analog failures John Larkin <jjlarkin@highlandtechnology.com> - 2017-02-14 19:20 -0800
Re: analog failures Tim Wescott <seemywebsite@myfooter.really> - 2017-02-14 17:46 -0600
Re: analog failures Jim Thompson <To-Email-Use-The-Envelope-Icon@On-My-Web-Site.com> - 2017-02-14 17:50 -0700
Re: analog failures Tim Wescott <tim@seemywebsite.com> - 2017-02-14 23:49 -0600
Re: analog failures Jim Thompson <To-Email-Use-The-Envelope-Icon@On-My-Web-Site.com> - 2017-02-15 07:03 -0700
Re: analog failures John Larkin <jjlarkinxyxy@highlandtechnology.com> - 2017-02-15 10:18 -0800
Re: analog failures Tim Wescott <seemywebsite@myfooter.really> - 2017-02-15 15:06 -0600
Re: analog failures legg <legg@nospam.magma.ca> - 2017-02-16 23:06 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 07:00 -0800
Re: analog failures legg <legg@nospam.magma.ca> - 2017-02-17 13:22 -0500
Re: analog failures Joerg <news@analogconsultants.com> - 2017-02-17 11:06 -0800
csiph-web