Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1722240 > unrolled thread

[PATCH v3 2/5] dt-bindings: scsi: ufs: add document for hisi-ufs

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  [PATCH v3 2/5] dt-bindings: scsi: ufs: add document for hisi-ufs Li Wei <liwei213@huawei.com> - 2017-08-29 10:50 +0200
    Re: [PATCH v3 2/5] dt-bindings: scsi: ufs: add document for hisi-ufs Rob Herring <robh@kernel.org> - 2017-09-01 18:00 +0200

#1722240 — [PATCH v3 2/5] dt-bindings: scsi: ufs: add document for hisi-ufs

add ufs node document for Hisilicon

Signed-off-by: Li Wei <liwei213@huawei.com>
---
 Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt

diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
new file mode 100644
index 000000000000..cfc84c821d50
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
@@ -0,0 +1,35 @@
+* Hisilicon Universal Flash Storage (UFS) Host Controller
+
+UFS nodes are defined to describe on-chip UFS hardware macro.
+Each UFS Host Controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains one of the following -
+			"hisilicon,hi3660-ufs" for hisi ufs host controller
+			 present on Hi3660 chipset.
+- reg               : should contain UFS register address space & UFS SYS CTRL register address,
+- interrupt-parent  : interrupt device
+- interrupts        : interrupt number
+- clocks	        : List of phandle and clock specifier pairs
+- clock-names       : List of clock input name strings sorted in the same
+		      order as the clocks property. "clk_ref", "clk_phy" is optional
+
+Optional properties for board device:
+- reset-gpio			: specifies to reset devices
+
+Example:
+
+	ufs: ufs@ff3b0000 {
+		compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs";
+		/* 0: HCI standard */
+		/* 1: UFS SYS CTRL */
+		reg = <0x0 0xff3b0000 0x0 0x1000>,
+			<0x0 0xff3b1000 0x0 0x1000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
+			<&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
+		clock-names = "clk_ref", "clk_phy";
+		freq-table-hz = <0 0>, <0 0>;
+		reset-gpio = <&gpio18 1 0>;
+	}
-- 
2.11.0

[toc] | [next] | [standalone]

#1725185

On Tue, Aug 29, 2017 at 04:41:13PM +0800, Li Wei wrote:
> add ufs node document for Hisilicon
> 
> Signed-off-by: Li Wei <liwei213@huawei.com>
> ---
>  Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 35 ++++++++++++++++++++++
>  1 file changed, 35 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt
> 
> diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
> new file mode 100644
> index 000000000000..cfc84c821d50
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
> @@ -0,0 +1,35 @@
> +* Hisilicon Universal Flash Storage (UFS) Host Controller
> +
> +UFS nodes are defined to describe on-chip UFS hardware macro.
> +Each UFS Host Controller should have its own node.
> +
> +Required properties:
> +- compatible        : compatible list, contains one of the following -
> +			"hisilicon,hi3660-ufs" for hisi ufs host controller
> +			 present on Hi3660 chipset.
> +- reg               : should contain UFS register address space & UFS SYS CTRL register address,
> +- interrupt-parent  : interrupt device
> +- interrupts        : interrupt number
> +- clocks	        : List of phandle and clock specifier pairs
> +- clock-names       : List of clock input name strings sorted in the same
> +		      order as the clocks property. "clk_ref", "clk_phy" is optional
> +
> +Optional properties for board device:
> +- reset-gpio			: specifies to reset devices

reset-gpios

Really, this is should be in a sub node representing the device. It's 
fine if this is it, but if we start adding power supplies and other 
properties it should be a separate node.

> +
> +Example:
> +
> +	ufs: ufs@ff3b0000 {
> +		compatible = "jedec,ufs-1.1", "hisilicon,hi3660-ufs";

Need to reverse the order here. Most specific first.

> +		/* 0: HCI standard */
> +		/* 1: UFS SYS CTRL */
> +		reg = <0x0 0xff3b0000 0x0 0x1000>,
> +			<0x0 0xff3b1000 0x0 0x1000>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
> +			<&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
> +		clock-names = "clk_ref", "clk_phy";
> +		freq-table-hz = <0 0>, <0 0>;
> +		reset-gpio = <&gpio18 1 0>;
> +	}
> -- 
> 2.11.0
> 

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web