Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1681004 > unrolled thread

[PATCH v6 0/4] Synopsys Designware HDMI Video Capture Controller + PHY

Back to article view | Back to linux.kernel

Contents

  [PATCH v6 0/4] Synopsys Designware HDMI Video Capture Controller + PHY Jose Abreu <Jose.Abreu@synopsys.com> - 2017-07-04 16:20 +0200
    [PATCH v6 3/4] MAINTAINERS: Add entry for Synopsys Designware HDMI drivers Jose Abreu <Jose.Abreu@synopsys.com> - 2017-07-04 16:20 +0200
    [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware HDMI RX Jose Abreu <Jose.Abreu@synopsys.com> - 2017-07-04 16:20 +0200
      Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware  HDMI RX Sylwester Nawrocki <snawrocki@kernel.org> - 2017-07-05 23:00 +0200
        Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware  HDMI RX Jose Abreu <Jose.Abreu@synopsys.com> - 2017-07-06 12:30 +0200
          Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware  HDMI RX Sylwester Nawrocki <snawrocki@kernel.org> - 2017-07-06 22:40 +0200
            Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware  HDMI RX Jose Abreu <Jose.Abreu@synopsys.com> - 2017-07-07 11:40 +0200
    [PATCH v6 1/4] [media] platform: Add Synopsys Designware HDMI RX PHY e405 Driver Jose Abreu <Jose.Abreu@synopsys.com> - 2017-07-04 16:20 +0200

#1681004 — [PATCH v6 0/4] Synopsys Designware HDMI Video Capture Controller + PHY

The Synopsys Designware HDMI RX controller is an HDMI receiver controller that
is responsible to process digital data that comes from a phy. The final result
is a stream of raw video data that can then be connected to a video DMA, for
example, and transfered into RAM so that it can be displayed.

The controller + phy available in this series natively support all HDMI 1.4 and
HDMI 2.0 modes, including deep color. Although, the driver is quite in its
initial stage and unfortunatelly only non deep color modes are supported. Also,
audio is not yet supported in the driver (the controller has several audio
output interfaces).

Version 6 addresses review comments from Hans Verkuil regarding CEC, HDCP 1.4
and adds the s_dv_timings() callback, as well as the V4L2_CID_DV_RX_POWER_PRESENT
ctrl.

This series depends on the patch at [1].

This series was tested in a FPGA platform using an embedded platform called
ARC AXS101.

Jose Abreu (4):
  [media] platform: Add Synopsys Designware HDMI RX PHY e405 Driver
  [media] platform: Add Synopsys Designware HDMI RX Controller Driver
  MAINTAINERS: Add entry for Synopsys Designware HDMI drivers
  dt-bindings: media: Document Synopsys Designware HDMI RX

Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>

[1] https://patchwork.linuxtv.org/patch/41834/

 .../devicetree/bindings/media/snps,dw-hdmi-rx.txt  |   70 +
 MAINTAINERS                                        |    7 +
 drivers/media/platform/Kconfig                     |    2 +
 drivers/media/platform/Makefile                    |    2 +
 drivers/media/platform/dwc/Kconfig                 |   23 +
 drivers/media/platform/dwc/Makefile                |    2 +
 drivers/media/platform/dwc/dw-hdmi-phy-e405.c      |  844 +++++++++
 drivers/media/platform/dwc/dw-hdmi-phy-e405.h      |   63 +
 drivers/media/platform/dwc/dw-hdmi-rx.c            | 1809 ++++++++++++++++++++
 drivers/media/platform/dwc/dw-hdmi-rx.h            |  441 +++++
 include/media/dwc/dw-hdmi-phy-pdata.h              |  128 ++
 include/media/dwc/dw-hdmi-rx-pdata.h               |   70 +
 12 files changed, 3461 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
 create mode 100644 drivers/media/platform/dwc/Kconfig
 create mode 100644 drivers/media/platform/dwc/Makefile
 create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.c
 create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.h
 create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.c
 create mode 100644 drivers/media/platform/dwc/dw-hdmi-rx.h
 create mode 100644 include/media/dwc/dw-hdmi-phy-pdata.h
 create mode 100644 include/media/dwc/dw-hdmi-rx-pdata.h

-- 
1.9.1

[toc] | [next] | [standalone]

#1681005 — [PATCH v6 3/4] MAINTAINERS: Add entry for Synopsys Designware HDMI drivers

Add a entry for Synopsys Designware HDMI Receivers drivers
and phys.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index c4be6d4..7ebc6dd 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11354,6 +11354,13 @@ L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/synopsys/
 
+SYNOPSYS DESIGNWARE HDMI RECEIVERS AND PHY DRIVERS
+M:	Jose Abreu <joabreu@synopsys.com>
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	drivers/media/platform/dwc/*
+F:	include/media/dwc/*
+
 SYNOPSYS DESIGNWARE I2C DRIVER
 M:	Jarkko Nikula <jarkko.nikula@linux.intel.com>
 R:	Andy Shevchenko <andriy.shevchenko@linux.intel.com>
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1681008 — [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware HDMI RX

Document the bindings for the Synopsys Designware HDMI RX.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Cc: devicetree@vger.kernel.org

Changes from v4:
	- Use "cfg" instead of "cfg-clk" (Rob)
	- Change node names (Rob)
Changes from v3:
	- Document the new DT bindings suggested by Sylwester
Changes from v2:
	- Document edid-phandle property
---
 .../devicetree/bindings/media/snps,dw-hdmi-rx.txt  | 70 ++++++++++++++++++++++
 1 file changed, 70 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt

diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
new file mode 100644
index 0000000..449b8a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
@@ -0,0 +1,70 @@
+Synopsys DesignWare HDMI RX Decoder
+===================================
+
+This document defines device tree properties for the Synopsys DesignWare HDMI
+RX Decoder (DWC HDMI RX). It doesn't constitute a device tree binding
+specification by itself but is meant to be referenced by platform-specific
+device tree bindings.
+
+When referenced from platform device tree bindings the properties defined in
+this document are defined as follows.
+
+- compatible: Shall be "snps,dw-hdmi-rx".
+
+- reg: Memory mapped base address and length of the DWC HDMI RX registers.
+
+- interrupts: Reference to the DWC HDMI RX interrupt and 5v sense interrupt.
+
+- clocks: Phandle to the config clock block.
+
+- clock-names: Shall be "cfg".
+
+- edid-phandle: phandle to the EDID handler block.
+
+- #address-cells: Shall be 1.
+
+- #size-cells: Shall be 0.
+
+You also have to create a subnode for phy driver. Phy properties are as follows.
+
+- compatible: Shall be "snps,dw-hdmi-phy-e405".
+
+- reg: Shall be JTAG address of phy.
+
+- clocks: Phandle for cfg clock.
+
+- clock-names:Shall be "cfg".
+
+A sample binding is now provided. The compatible string is for a SoC which has
+has a Synopsys DesignWare HDMI RX decoder inside.
+
+Example:
+
+dw_hdmi_soc: dw-hdmi-soc@0 {
+	compatible = "snps,dw-hdmi-soc";
+	reg = <0x11c00 0x1000>; /* EDIDs */
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	hdmi-rx@0 {
+		compatible = "snps,dw-hdmi-rx";
+		reg = <0x0 0x10000>;
+		interrupts = <1 2>;
+		edid-phandle = <&dw_hdmi_soc>;
+
+		clocks = <&dw_hdmi_refclk>;
+		clock-names = "cfg";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hdmi-phy@fc {
+			compatible = "snps,dw-hdmi-phy-e405";
+			reg = <0xfc>;
+
+			clocks = <&dw_hdmi_refclk>;
+			clock-names = "cfg";
+		};
+	};
+};
-- 
1.9.1

[toc] | [prev] | [next] | [standalone]

#1681802 — Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware HDMI RX

On 07/04/2017 04:11 PM, Jose Abreu wrote:
> Document the bindings for the Synopsys Designware HDMI RX.
> 
> Signed-off-by: Jose Abreu <joabreu@synopsys.com>

> ---
>   .../devicetree/bindings/media/snps,dw-hdmi-rx.txt  | 70 ++++++++++++++++++++++
>   1 file changed, 70 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt

Could you make the DT binding documentation patch first patch in the series?
Now checkpatch will complain about undocumented compatible string when 
the driver patches are applied alone.

> diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt 
>b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
> new file mode 100644
> index 0000000..449b8a2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
> @@ -0,0 +1,70 @@
> +Synopsys DesignWare HDMI RX Decoder
> +===================================
> +
> +This document defines device tree properties for the Synopsys DesignWare HDMI
> +RX Decoder (DWC HDMI RX). It doesn't constitute a device tree binding
> +specification by itself but is meant to be referenced by platform-specific
> +device tree bindings.
> +
> +When referenced from platform device tree bindings the properties defined in
> +this document are defined as follows.

It would be good to make it clear which properties are required and which are
optional. And also to mention the properties below belong to the HDMI RX node.

> +- compatible: Shall be "snps,dw-hdmi-rx".
> +
> +- reg: Memory mapped base address and length of the DWC HDMI RX registers.
> +
> +- interrupts: Reference to the DWC HDMI RX interrupt and 5v sense interrupt.

s/5v/HDMI 5V ?

> +
> +- clocks: Phandle to the config clock block.
> +
> +- clock-names: Shall be "cfg".
> +
> +- edid-phandle: phandle to the EDID handler block.

Could you make this property optional and when it is missing assume that device
corresponding to the parent node of this node handles EDID? This way we could
avoid having property pointing to the parent node.

> +- #address-cells: Shall be 1.
> +
> +- #size-cells: Shall be 0.
> +
> +You also have to create a subnode for phy driver. Phy properties are as follows.

s/phy driver. Phy/the PHY device. PHY ?

Might be also worth to make it explicit these are all required properties.

> +- compatible: Shall be "snps,dw-hdmi-phy-e405".
> +
> +- reg: Shall be JTAG address of phy.

s/phy/the PHY ?

> +- clocks: Phandle for cfg clock.
> +
> +- clock-names:Shall be "cfg".
> +
> +A sample binding is now provided. The compatible string is for a SoC which has
> +has a Synopsys DesignWare HDMI RX decoder inside.
> +
> +Example:
> +
> +dw_hdmi_soc: dw-hdmi-soc@0 {
> +	compatible = "snps,dw-hdmi-soc";

Perhaps just make it

	compatible = "...";
?

> +	reg = <0x11c00 0x1000>; /* EDIDs */

This is not relevant and undocumented, will likely be part of documentation 
of other binding thus I'd suggest dropping this reg property.

> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	ranges;
> +
> +	hdmi-rx@0 {
> +		compatible = "snps,dw-hdmi-rx";
> +		reg = <0x0 0x10000>;
> +		interrupts = <1 2>;
> +		edid-phandle = <&dw_hdmi_soc>;
> +
> +		clocks = <&dw_hdmi_refclk>;
> +		clock-names = "cfg";
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		hdmi-phy@fc {
> +			compatible = "snps,dw-hdmi-phy-e405";
> +			reg = <0xfc>;
> +
> +			clocks = <&dw_hdmi_refclk>;
> +			clock-names = "cfg";
> +		};
> +	};
> +};

Otherwise looks good. I'll likely not have comments to the other patches.

--
Regards,
Sylwester
 

[toc] | [prev] | [next] | [standalone]

#1682320 — Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware HDMI RX

Hi Sylwester,


On 05-07-2017 21:52, Sylwester Nawrocki wrote:
> On 07/04/2017 04:11 PM, Jose Abreu wrote:
>> Document the bindings for the Synopsys Designware HDMI RX.
>>
>> Signed-off-by: Jose Abreu <joabreu@synopsys.com>
>> ---
>>   .../devicetree/bindings/media/snps,dw-hdmi-rx.txt  | 70 ++++++++++++++++++++++
>>   1 file changed, 70 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
> Could you make the DT binding documentation patch first patch in the series?
> Now checkpatch will complain about undocumented compatible string when 
> the driver patches are applied alone.

Sure.

>
>> diff --git a/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt 
>> b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
>> new file mode 100644
>> index 0000000..449b8a2
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/snps,dw-hdmi-rx.txt
>> @@ -0,0 +1,70 @@
>> +Synopsys DesignWare HDMI RX Decoder
>> +===================================
>> +
>> +This document defines device tree properties for the Synopsys DesignWare HDMI
>> +RX Decoder (DWC HDMI RX). It doesn't constitute a device tree binding
>> +specification by itself but is meant to be referenced by platform-specific
>> +device tree bindings.
>> +
>> +When referenced from platform device tree bindings the properties defined in
>> +this document are defined as follows.
> It would be good to make it clear which properties are required and which are
> optional. And also to mention the properties below belong to the HDMI RX node.

Ok.

>
>> +- compatible: Shall be "snps,dw-hdmi-rx".
>> +
>> +- reg: Memory mapped base address and length of the DWC HDMI RX registers.
>> +
>> +- interrupts: Reference to the DWC HDMI RX interrupt and 5v sense interrupt.
> s/5v/HDMI 5V ?

Ok.

>
>> +
>> +- clocks: Phandle to the config clock block.
>> +
>> +- clock-names: Shall be "cfg".
>> +
>> +- edid-phandle: phandle to the EDID handler block.
> Could you make this property optional and when it is missing assume that device
> corresponding to the parent node of this node handles EDID? This way we could
> avoid having property pointing to the parent node.

Hmm, this is for the CEC notifier. Do you mean I should grab the
parent device for the notifier? This property is already optional
if cec is not enabled though.

>
>> +- #address-cells: Shall be 1.
>> +
>> +- #size-cells: Shall be 0.
>> +
>> +You also have to create a subnode for phy driver. Phy properties are as follows.
> s/phy driver. Phy/the PHY device. PHY ?
>
> Might be also worth to make it explicit these are all required properties.

Ok.

>
>> +- compatible: Shall be "snps,dw-hdmi-phy-e405".
>> +
>> +- reg: Shall be JTAG address of phy.
> s/phy/the PHY ?

Ok.

>
>> +- clocks: Phandle for cfg clock.
>> +
>> +- clock-names:Shall be "cfg".
>> +
>> +A sample binding is now provided. The compatible string is for a SoC which has
>> +has a Synopsys DesignWare HDMI RX decoder inside.
>> +
>> +Example:
>> +
>> +dw_hdmi_soc: dw-hdmi-soc@0 {
>> +	compatible = "snps,dw-hdmi-soc";
> Perhaps just make it
>
> 	compatible = "...";
> ?

Yeah, probably its better.

>
>> +	reg = <0x11c00 0x1000>; /* EDIDs */
> This is not relevant and undocumented, will likely be part of documentation 
> of other binding thus I'd suggest dropping this reg property.

Ok.

>
>> +	#address-cells = <1>;
>> +	#size-cells = <1>;
>> +	ranges;
>> +
>> +	hdmi-rx@0 {
>> +		compatible = "snps,dw-hdmi-rx";
>> +		reg = <0x0 0x10000>;
>> +		interrupts = <1 2>;
>> +		edid-phandle = <&dw_hdmi_soc>;
>> +
>> +		clocks = <&dw_hdmi_refclk>;
>> +		clock-names = "cfg";
>> +
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		hdmi-phy@fc {
>> +			compatible = "snps,dw-hdmi-phy-e405";
>> +			reg = <0xfc>;
>> +
>> +			clocks = <&dw_hdmi_refclk>;
>> +			clock-names = "cfg";
>> +		};
>> +	};
>> +};
> Otherwise looks good. I'll likely not have comments to the other patches.

Thanks for the review!

Best regards,
Jose Miguel Abreu

>
> --
> Regards,
> Sylwester
>  

[toc] | [prev] | [next] | [standalone]

#1682692 — Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware HDMI RX

On 07/06/2017 12:24 PM, Jose Abreu wrote:
>>> +- edid-phandle: phandle to the EDID handler block.
>>
>> Could you make this property optional and when it is missing assume that device
>> corresponding to the parent node of this node handles EDID? This way we could
>> avoid having property pointing to the parent node.
>
> Hmm, this is for the CEC notifier. Do you mean I should grab the
> parent device for the notifier? This property is already optional
> if cec is not enabled though.
 
Yes, device associated with the parent node. Something like:

 - edid-phandle - phandle to the EDID handler block; if this property is
  not specified it is assumed that EDID is handled by device described 
  by parent node of the HDMI RX node

Not sure if it is any better than always requiring edid-phandle property,
even when it is pointing to the parent node. We would need a DT maintainer's
opinion on that.

--
Thanks,
Sylwester

[toc] | [prev] | [next] | [standalone]

#1683085 — Re: [PATCH v6 4/4] dt-bindings: media: Document Synopsys Designware HDMI RX

On 06-07-2017 21:30, Sylwester Nawrocki wrote:
> On 07/06/2017 12:24 PM, Jose Abreu wrote:
>>>> +- edid-phandle: phandle to the EDID handler block.
>>> Could you make this property optional and when it is missing assume that device
>>> corresponding to the parent node of this node handles EDID? This way we could
>>> avoid having property pointing to the parent node.
>> Hmm, this is for the CEC notifier. Do you mean I should grab the
>> parent device for the notifier? This property is already optional
>> if cec is not enabled though.
>  
> Yes, device associated with the parent node. Something like:
>
>  - edid-phandle - phandle to the EDID handler block; if this property is
>   not specified it is assumed that EDID is handled by device described 
>   by parent node of the HDMI RX node
>
> Not sure if it is any better than always requiring edid-phandle property,
> even when it is pointing to the parent node. We would need a DT maintainer's
> opinion on that.

I will change and resend. I also have to fix a kbuild error when
cec is not enabled.

Best regards,
Jose Miguel Abreu

>
> --
> Thanks,
> Sylwester

[toc] | [prev] | [next] | [standalone]

#1681009 — [PATCH v6 1/4] [media] platform: Add Synopsys Designware HDMI RX PHY e405 Driver

This adds support for the Synopsys Designware HDMI RX PHY e405. This
phy receives and decodes HDMI video that is delivered to a controller.

Main features included in this driver are:
	- Equalizer algorithm that chooses the phy best settings
	according to the detected HDMI cable characteristics.
	- Support for scrambling
	- Support for HDMI 2.0 modes up to 6G (HDMI 4k@60Hz).

The driver was implemented as a standalone V4L2 subdevice and the
phy interface with the controller was implemented using V4L2 ioctls. I
do not know if this is the best option but it is not possible to use the
existing API functions directly as we need specific functions that will
be called by the controller at specific configuration stages.

There is also a bidirectional communication between controller and phy:
The phy must provide functions that the controller will call (i.e.
configuration functions) and the controller must provide read/write
callbacks, as well as other specific functions.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>

Changes from v4:
	- Use usleep_range (Sylwester)
	- Remove some comments (Sylwester)
	- Parse phy version from of_device_id (Sylwester)
	- Use "cfg" instead of "cfg-clk" (Sylwester, Rob)
	- Change some messages to dev_dbg (Sylwester)
Changes from v3:
	- Use v4l2 async API (Sylwester)
	- Use clock API (Sylwester)
	- Add compatible string (Sylwester)
Changes from RFC:
	- Remove a bunch of functions that can be collapsed into
	a single config() function
	- Add comments for the callbacks and structures (Hans)
---
 drivers/media/platform/Kconfig                |   2 +
 drivers/media/platform/Makefile               |   2 +
 drivers/media/platform/dwc/Kconfig            |   8 +
 drivers/media/platform/dwc/Makefile           |   1 +
 drivers/media/platform/dwc/dw-hdmi-phy-e405.c | 844 ++++++++++++++++++++++++++
 drivers/media/platform/dwc/dw-hdmi-phy-e405.h |  63 ++
 include/media/dwc/dw-hdmi-phy-pdata.h         | 128 ++++
 7 files changed, 1048 insertions(+)
 create mode 100644 drivers/media/platform/dwc/Kconfig
 create mode 100644 drivers/media/platform/dwc/Makefile
 create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.c
 create mode 100644 drivers/media/platform/dwc/dw-hdmi-phy-e405.h
 create mode 100644 include/media/dwc/dw-hdmi-phy-pdata.h

diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
index 1313cd5..47d4a50 100644
--- a/drivers/media/platform/Kconfig
+++ b/drivers/media/platform/Kconfig
@@ -33,6 +33,8 @@ source "drivers/media/platform/omap/Kconfig"
 
 source "drivers/media/platform/blackfin/Kconfig"
 
+source "drivers/media/platform/dwc/Kconfig"
+
 config VIDEO_SH_VOU
 	tristate "SuperH VOU video output driver"
 	depends on MEDIA_CAMERA_SUPPORT
diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
index 9beadc7..e6a55fb 100644
--- a/drivers/media/platform/Makefile
+++ b/drivers/media/platform/Makefile
@@ -86,3 +86,5 @@ obj-$(CONFIG_VIDEO_MEDIATEK_MDP)	+= mtk-mdp/
 obj-$(CONFIG_VIDEO_MEDIATEK_JPEG)	+= mtk-jpeg/
 
 obj-$(CONFIG_VIDEO_QCOM_VENUS)		+= qcom/venus/
+
+obj-y	+= dwc/
diff --git a/drivers/media/platform/dwc/Kconfig b/drivers/media/platform/dwc/Kconfig
new file mode 100644
index 0000000..361d38d
--- /dev/null
+++ b/drivers/media/platform/dwc/Kconfig
@@ -0,0 +1,8 @@
+config VIDEO_DWC_HDMI_PHY_E405
+	tristate "Synopsys Designware HDMI RX PHY e405 driver"
+	depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+	help
+	  Support for Synopsys Designware HDMI RX PHY. Version is e405.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called dw-hdmi-phy-e405.
diff --git a/drivers/media/platform/dwc/Makefile b/drivers/media/platform/dwc/Makefile
new file mode 100644
index 0000000..fc3b62c
--- /dev/null
+++ b/drivers/media/platform/dwc/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_VIDEO_DWC_HDMI_PHY_E405) += dw-hdmi-phy-e405.o
diff --git a/drivers/media/platform/dwc/dw-hdmi-phy-e405.c b/drivers/media/platform/dwc/dw-hdmi-phy-e405.c
new file mode 100644
index 0000000..26d70ca
--- /dev/null
+++ b/drivers/media/platform/dwc/dw-hdmi-phy-e405.c
@@ -0,0 +1,844 @@
+/*
+ * Synopsys Designware HDMI PHY E405 driver
+ *
+ * This Synopsys dw-phy-e405 software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS"  WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-subdev.h>
+#include <media/dwc/dw-hdmi-phy-pdata.h>
+#include "dw-hdmi-phy-e405.h"
+
+MODULE_AUTHOR("Jose Abreu <joabreu@synopsys.com>");
+MODULE_DESCRIPTION("Designware HDMI PHY e405 driver");
+MODULE_LICENSE("Dual MIT/GPL");
+
+#define PHY_EQ_WAIT_TIME_START			3
+#define PHY_EQ_SLEEP_TIME_CDR			30
+#define PHY_EQ_SLEEP_TIME_ACQ			1
+#define PHY_EQ_BOUNDSPREAD			20
+#define PHY_EQ_MIN_ACQ_STABLE			3
+#define PHY_EQ_ACC_LIMIT			360
+#define PHY_EQ_ACC_MIN_LIMIT			0
+#define PHY_EQ_MAX_SETTING			13
+#define PHY_EQ_SHORT_CABLE_SETTING		4
+#define PHY_EQ_ERROR_CABLE_SETTING		4
+#define PHY_EQ_MIN_SLOPE			50
+#define PHY_EQ_AVG_ACQ				5
+#define PHY_EQ_MINMAX_NTRIES			3
+#define PHY_EQ_EQUALIZED_COUNTER_VAL		512
+#define PHY_EQ_EQUALIZED_COUNTER_VAL_HDMI20	512
+#define PHY_EQ_MINMAX_MAXDIFF			4
+#define PHY_EQ_MINMAX_MAXDIFF_HDMI20		2
+#define PHY_EQ_FATBIT_MASK			0x0000
+#define PHY_EQ_FATBIT_MASK_4K			0x0c03
+#define PHY_EQ_FATBIT_MASK_HDMI20		0x0e03
+
+struct dw_phy_eq_ch {
+	u16 best_long_setting;
+	u8 valid_long_setting;
+	u16 best_short_setting;
+	u8 valid_short_setting;
+	u16 best_setting;
+	u16 acc;
+	u16 acq;
+	u16 last_acq;
+	u16 upper_bound_acq;
+	u16 lower_bound_acq;
+	u16 out_bound_acq;
+	u16 read_acq;
+};
+
+static const struct dw_phy_mpll_config {
+	u16 addr;
+	u16 val;
+} dw_phy_e405_mpll_cfg[] = {
+	{ 0x27, 0x1B94 },
+	{ 0x28, 0x16D2 },
+	{ 0x29, 0x12D9 },
+	{ 0x2A, 0x3249 },
+	{ 0x2B, 0x3653 },
+	{ 0x2C, 0x3436 },
+	{ 0x2D, 0x124D },
+	{ 0x2E, 0x0001 },
+	{ 0xCE, 0x0505 },
+	{ 0xCF, 0x0505 },
+	{ 0xD0, 0x0000 },
+	{ 0x00, 0x0000 },
+};
+
+struct dw_phy_dev {
+	struct device *dev;
+	struct dw_phy_pdata *config;
+	unsigned int version;
+	struct clk *clk;
+	u16 cfg_clk;
+	bool phy_enabled;
+	struct v4l2_subdev sd;
+	u16 mpll_status;
+	unsigned char color_depth;
+	bool hdmi2;
+	bool scrambling;
+	struct mutex lock;
+};
+
+static inline struct dw_phy_dev *to_dw_dev(struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct dw_phy_dev, sd);
+}
+
+static void phy_write(struct dw_phy_dev *dw_dev, u16 val, u16 addr)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	dw_dev->config->funcs->write(arg, val, addr);
+}
+
+static u16 phy_read(struct dw_phy_dev *dw_dev, u16 addr)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	return dw_dev->config->funcs->read(arg, addr);
+}
+
+static void phy_reset(struct dw_phy_dev *dw_dev, int enable)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	dw_dev->config->funcs->reset(arg, enable);
+}
+
+static void phy_pddq(struct dw_phy_dev *dw_dev, int enable)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	dw_dev->config->funcs->pddq(arg, enable);
+}
+
+static void phy_svsmode(struct dw_phy_dev *dw_dev, int enable)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	dw_dev->config->funcs->svsmode(arg, enable);
+}
+
+static void phy_zcal_reset(struct dw_phy_dev *dw_dev)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	dw_dev->config->funcs->zcal_reset(arg);
+}
+
+static bool phy_zcal_done(struct dw_phy_dev *dw_dev)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	return dw_dev->config->funcs->zcal_done(arg);
+}
+
+static bool phy_tmds_valid(struct dw_phy_dev *dw_dev)
+{
+	void *arg = dw_dev->config->funcs_arg;
+
+	return dw_dev->config->funcs->tmds_valid(arg);
+}
+
+static int dw_phy_eq_test(struct dw_phy_dev *dw_dev,
+		u16 *fat_bit_mask, int *min_max_length)
+{
+	u16 main_fsm_status, val;
+	int i;
+
+	for (i = 0; i < PHY_EQ_WAIT_TIME_START; i++) {
+		main_fsm_status = phy_read(dw_dev, PHY_MAINFSM_STATUS1);
+		if (main_fsm_status & 0x100)
+			break;
+		mdelay(PHY_EQ_SLEEP_TIME_CDR);
+	}
+
+	if (i == PHY_EQ_WAIT_TIME_START) {
+		dev_dbg(dw_dev->dev, "phy start conditions not achieved\n");
+		return -ETIMEDOUT;
+	}
+
+	if (main_fsm_status & 0x400) {
+		dev_dbg(dw_dev->dev, "invalid pll rate\n");
+		return -EINVAL;
+	}
+
+	val = (phy_read(dw_dev, PHY_CDR_CTRL_CNT) & 0x300) >> 8;
+	if (val == 0x1) {
+		/* HDMI 2.0 */
+		*fat_bit_mask = PHY_EQ_FATBIT_MASK_HDMI20;
+		*min_max_length = PHY_EQ_MINMAX_MAXDIFF_HDMI20;
+		dev_dbg(dw_dev->dev, "[EQUALIZER] using HDMI 2.0 values\n");
+	} else if (!(main_fsm_status & 0x600)) {
+		/* HDMI 1.4 (pll rate = 0) */
+		*fat_bit_mask = PHY_EQ_FATBIT_MASK_4K;
+		*min_max_length = PHY_EQ_MINMAX_MAXDIFF;
+		dev_dbg(dw_dev->dev, "[EQUALIZER] using HDMI 1.4@4k values\n");
+	} else {
+		/* HDMI 1.4 */
+		*fat_bit_mask = PHY_EQ_FATBIT_MASK;
+		*min_max_length = PHY_EQ_MINMAX_MAXDIFF;
+		dev_dbg(dw_dev->dev, "[EQUALIZER] using HDMI 1.4 values\n");
+	}
+
+	return 0;
+}
+
+static void dw_phy_eq_default(struct dw_phy_dev *dw_dev)
+{
+	phy_write(dw_dev, 0x08A8, PHY_CH0_EQ_CTRL1);
+	phy_write(dw_dev, 0x0020, PHY_CH0_EQ_CTRL2);
+	phy_write(dw_dev, 0x08A8, PHY_CH1_EQ_CTRL1);
+	phy_write(dw_dev, 0x0020, PHY_CH1_EQ_CTRL2);
+	phy_write(dw_dev, 0x08A8, PHY_CH2_EQ_CTRL1);
+	phy_write(dw_dev, 0x0020, PHY_CH2_EQ_CTRL2);
+}
+
+static void dw_phy_eq_single(struct dw_phy_dev *dw_dev)
+{
+	phy_write(dw_dev, 0x0211, PHY_CH0_EQ_CTRL1);
+	phy_write(dw_dev, 0x0211, PHY_CH1_EQ_CTRL1);
+	phy_write(dw_dev, 0x0211, PHY_CH2_EQ_CTRL1);
+}
+
+static void dw_phy_eq_equal_setting(struct dw_phy_dev *dw_dev,
+		u16 lock_vector)
+{
+	phy_write(dw_dev, lock_vector, PHY_CH0_EQ_CTRL4);
+	phy_write(dw_dev, 0x0024, PHY_CH0_EQ_CTRL2);
+	phy_write(dw_dev, 0x0026, PHY_CH0_EQ_CTRL2);
+	phy_read(dw_dev, PHY_CH0_EQ_STATUS2);
+	phy_write(dw_dev, lock_vector, PHY_CH1_EQ_CTRL4);
+	phy_write(dw_dev, 0x0024, PHY_CH1_EQ_CTRL2);
+	phy_write(dw_dev, 0x0026, PHY_CH1_EQ_CTRL2);
+	phy_read(dw_dev, PHY_CH1_EQ_STATUS2);
+	phy_write(dw_dev, lock_vector, PHY_CH2_EQ_CTRL4);
+	phy_write(dw_dev, 0x0024, PHY_CH2_EQ_CTRL2);
+	phy_write(dw_dev, 0x0026, PHY_CH2_EQ_CTRL2);
+	phy_read(dw_dev, PHY_CH2_EQ_STATUS2);
+}
+
+static void dw_phy_eq_equal_setting_ch0(struct dw_phy_dev *dw_dev,
+		u16 lock_vector)
+{
+	phy_write(dw_dev, lock_vector, PHY_CH0_EQ_CTRL4);
+	phy_write(dw_dev, 0x0024, PHY_CH0_EQ_CTRL2);
+	phy_write(dw_dev, 0x0026, PHY_CH0_EQ_CTRL2);
+	phy_read(dw_dev, PHY_CH0_EQ_STATUS2);
+}
+
+static void dw_phy_eq_equal_setting_ch1(struct dw_phy_dev *dw_dev,
+		u16 lock_vector)
+{
+	phy_write(dw_dev, lock_vector, PHY_CH1_EQ_CTRL4);
+	phy_write(dw_dev, 0x0024, PHY_CH1_EQ_CTRL2);
+	phy_write(dw_dev, 0x0026, PHY_CH1_EQ_CTRL2);
+	phy_read(dw_dev, PHY_CH1_EQ_STATUS2);
+}
+
+static void dw_phy_eq_equal_setting_ch2(struct dw_phy_dev *dw_dev,
+		u16 lock_vector)
+{
+	phy_write(dw_dev, lock_vector, PHY_CH2_EQ_CTRL4);
+	phy_write(dw_dev, 0x0024, PHY_CH2_EQ_CTRL2);
+	phy_write(dw_dev, 0x0026, PHY_CH2_EQ_CTRL2);
+	phy_read(dw_dev, PHY_CH2_EQ_STATUS2);
+}
+
+static void dw_phy_eq_auto_calib(struct dw_phy_dev *dw_dev)
+{
+	phy_write(dw_dev, 0x1809, PHY_MAINFSM_CTRL);
+	phy_write(dw_dev, 0x1819, PHY_MAINFSM_CTRL);
+	phy_write(dw_dev, 0x1809, PHY_MAINFSM_CTRL);
+}
+
+static void dw_phy_eq_init_vars(struct dw_phy_eq_ch *ch)
+{
+	ch->acc = 0;
+	ch->acq = 0;
+	ch->last_acq = 0;
+	ch->valid_long_setting = 0;
+	ch->valid_short_setting = 0;
+	ch->best_setting = PHY_EQ_SHORT_CABLE_SETTING;
+}
+
+static bool dw_phy_eq_acquire_early_cnt(struct dw_phy_dev *dw_dev,
+		u16 setting, u16 acq, struct dw_phy_eq_ch *ch0,
+		struct dw_phy_eq_ch *ch1, struct dw_phy_eq_ch *ch2)
+{
+	u16 lock_vector = 0x1;
+	int i;
+
+	lock_vector <<= setting;
+	ch0->out_bound_acq = 0;
+	ch1->out_bound_acq = 0;
+	ch2->out_bound_acq = 0;
+	ch0->acq = 0;
+	ch1->acq = 0;
+	ch2->acq = 0;
+
+	dw_phy_eq_equal_setting(dw_dev, lock_vector);
+	dw_phy_eq_auto_calib(dw_dev);
+
+	mdelay(PHY_EQ_SLEEP_TIME_CDR);
+	if (!phy_tmds_valid(dw_dev))
+		dev_dbg(dw_dev->dev, "TMDS is NOT valid\n");
+
+	ch0->read_acq = phy_read(dw_dev, PHY_CH0_EQ_STATUS3);
+	ch1->read_acq = phy_read(dw_dev, PHY_CH1_EQ_STATUS3);
+	ch2->read_acq = phy_read(dw_dev, PHY_CH2_EQ_STATUS3);
+
+	ch0->acq += ch0->read_acq;
+	ch1->acq += ch1->read_acq;
+	ch2->acq += ch2->read_acq;
+
+	ch0->upper_bound_acq = ch0->read_acq + PHY_EQ_BOUNDSPREAD;
+	ch0->lower_bound_acq = ch0->read_acq - PHY_EQ_BOUNDSPREAD;
+	ch1->upper_bound_acq = ch1->read_acq + PHY_EQ_BOUNDSPREAD;
+	ch1->lower_bound_acq = ch1->read_acq - PHY_EQ_BOUNDSPREAD;
+	ch2->upper_bound_acq = ch2->read_acq + PHY_EQ_BOUNDSPREAD;
+	ch2->lower_bound_acq = ch2->read_acq - PHY_EQ_BOUNDSPREAD;
+
+	for (i = 1; i < acq; i++) {
+		dw_phy_eq_auto_calib(dw_dev);
+		mdelay(PHY_EQ_SLEEP_TIME_ACQ);
+
+		if ((ch0->read_acq > ch0->upper_bound_acq) ||
+				(ch0->read_acq < ch0->lower_bound_acq))
+			ch0->out_bound_acq++;
+		if ((ch1->read_acq > ch1->upper_bound_acq) ||
+				(ch1->read_acq < ch1->lower_bound_acq))
+			ch1->out_bound_acq++;
+		if ((ch2->read_acq > ch2->upper_bound_acq) ||
+				(ch2->read_acq < ch1->lower_bound_acq))
+			ch2->out_bound_acq++;
+
+		if (i == PHY_EQ_MIN_ACQ_STABLE) {
+			if ((ch0->out_bound_acq == 0) &&
+					(ch1->out_bound_acq == 0) &&
+					(ch2->out_bound_acq == 0)) {
+				acq = 3;
+				break;
+			}
+		}
+
+		ch0->read_acq = phy_read(dw_dev, PHY_CH0_EQ_STATUS3);
+		ch1->read_acq = phy_read(dw_dev, PHY_CH1_EQ_STATUS3);
+		ch2->read_acq = phy_read(dw_dev, PHY_CH2_EQ_STATUS3);
+
+		ch0->acq += ch0->read_acq;
+		ch1->acq += ch1->read_acq;
+		ch2->acq += ch2->read_acq;
+	}
+
+	ch0->acq = ch0->acq / acq;
+	ch1->acq = ch1->acq / acq;
+	ch2->acq = ch2->acq / acq;
+
+	return true;
+}
+
+static int dw_phy_eq_test_type(u16 setting, bool tmds_valid,
+		struct dw_phy_eq_ch *ch)
+{
+	u16 step_slope = 0;
+
+	if ((ch->acq < ch->last_acq) && tmds_valid) {
+		/* Long cable equalization */
+		ch->acc += ch->last_acq - ch->acq;
+		if ((ch->valid_long_setting == 0) && (ch->acq < 512) &&
+				(ch->acc > 0)) {
+			ch->best_long_setting = setting;
+			ch->valid_long_setting = 1;
+		}
+		step_slope = ch->last_acq - ch->acq;
+	}
+
+	if (tmds_valid && (ch->valid_short_setting == 0)) {
+		/* Short cable equalization */
+		if ((setting < PHY_EQ_SHORT_CABLE_SETTING) &&
+				(ch->acq < PHY_EQ_EQUALIZED_COUNTER_VAL)) {
+			ch->best_short_setting= setting;
+			ch->valid_short_setting = 1;
+		}
+
+		if (setting == PHY_EQ_SHORT_CABLE_SETTING) {
+			ch->best_short_setting = PHY_EQ_SHORT_CABLE_SETTING;
+			ch->valid_short_setting = 1;
+		}
+	}
+
+	if (ch->valid_long_setting && (ch->acc > PHY_EQ_ACC_LIMIT)) {
+		ch->best_setting = ch->best_long_setting;
+		return 1;
+	}
+
+	if ((setting == PHY_EQ_MAX_SETTING) && (ch->acc < PHY_EQ_ACC_LIMIT) &&
+			ch->valid_short_setting) {
+		ch->best_setting = ch->best_short_setting;
+		return 2;
+	}
+
+	if ((setting == PHY_EQ_MAX_SETTING) && tmds_valid &&
+			(ch->acc > PHY_EQ_ACC_LIMIT) &&
+			(step_slope > PHY_EQ_MIN_SLOPE)) {
+		ch->best_setting = PHY_EQ_MAX_SETTING;
+		return 3;
+	}
+
+	if (setting == PHY_EQ_MAX_SETTING) {
+		ch->best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+		return 255;
+	}
+
+	return 0;
+}
+
+static bool dw_phy_eq_setting_finder(struct dw_phy_dev *dw_dev, u16 acq,
+		struct dw_phy_eq_ch *ch0, struct dw_phy_eq_ch *ch1,
+		struct dw_phy_eq_ch *ch2)
+{
+	u16 act = 0;
+	int ret_ch0 = 0, ret_ch1 = 0, ret_ch2 = 0;
+	bool tmds_valid = false;
+
+	dw_phy_eq_init_vars(ch0);
+	dw_phy_eq_init_vars(ch1);
+	dw_phy_eq_init_vars(ch2);
+
+	tmds_valid = dw_phy_eq_acquire_early_cnt(dw_dev, act, acq,
+			ch0, ch1, ch2);
+
+	while ((ret_ch0 == 0) || (ret_ch1 == 0) || (ret_ch2 == 0)) {
+		act++;
+
+		ch0->last_acq = ch0->acq;
+		ch1->last_acq = ch1->acq;
+		ch2->last_acq = ch2->acq;
+
+		tmds_valid = dw_phy_eq_acquire_early_cnt(dw_dev, act, acq,
+				ch0, ch1, ch2);
+
+		if (!ret_ch0)
+			ret_ch0 = dw_phy_eq_test_type(act, tmds_valid, ch0);
+		if (!ret_ch1)
+			ret_ch1 = dw_phy_eq_test_type(act, tmds_valid, ch1);
+		if (!ret_ch2)
+			ret_ch2 = dw_phy_eq_test_type(act, tmds_valid, ch2);
+	}
+
+	if ((ret_ch0 == 255) || (ret_ch1 == 255) || (ret_ch2 == 255))
+		return false;
+	return true;
+}
+
+static bool dw_phy_eq_maxvsmin(u16 ch0_setting, u16 ch1_setting,
+		u16 ch2_setting, u16 min_max_length)
+{
+	u16 min = ch0_setting, max = ch0_setting;
+
+	if (ch1_setting > max)
+		max = ch1_setting;
+	if (ch2_setting > max)
+		max = ch2_setting;
+	if (ch1_setting < min)
+		min = ch1_setting;
+	if (ch2_setting < min)
+		min = ch2_setting;
+
+	if ((max - min) > min_max_length)
+		return false;
+	return true;
+}
+
+static int dw_phy_eq_init(struct dw_phy_dev *dw_dev, u16 acq, bool force)
+{
+	struct dw_phy_eq_ch ch0, ch1, ch2;
+	u16 fat_bit_mask, lock_vector = 0x1;
+	int min_max_length, i, ret = 0;
+	u16 mpll_status;
+
+	if (dw_dev->version < 401)
+		return ret;
+	if (!dw_dev->phy_enabled)
+		return -EINVAL;
+
+	mpll_status = phy_read(dw_dev, PHY_CLK_MPLL_STATUS);
+	if (mpll_status == dw_dev->mpll_status && !force)
+		return ret;
+	dw_dev->mpll_status = mpll_status;
+
+	phy_write(dw_dev, 0x00, PHY_MAINFSM_OVR2);
+	phy_write(dw_dev, 0x00, PHY_CH0_EQ_CTRL3);
+	phy_write(dw_dev, 0x00, PHY_CH1_EQ_CTRL3);
+	phy_write(dw_dev, 0x00, PHY_CH2_EQ_CTRL3);
+
+	ret = dw_phy_eq_test(dw_dev, &fat_bit_mask, &min_max_length);
+	if (ret) {
+		if (ret == -EINVAL) /* Means equalizer is not needed */
+			ret = 0;
+
+		/* Do not change values if we don't have clock */
+		if (ret != -ETIMEDOUT) {
+			dw_phy_eq_default(dw_dev);
+			phy_pddq(dw_dev, 1);
+			phy_pddq(dw_dev, 0);
+		}
+	} else {
+		dw_phy_eq_single(dw_dev);
+		dw_phy_eq_equal_setting(dw_dev, 0x0001);
+		phy_write(dw_dev, fat_bit_mask, PHY_CH0_EQ_CTRL6);
+		phy_write(dw_dev, fat_bit_mask, PHY_CH1_EQ_CTRL6);
+		phy_write(dw_dev, fat_bit_mask, PHY_CH2_EQ_CTRL6);
+
+		for (i = 0; i < PHY_EQ_MINMAX_NTRIES; i++) {
+			if (dw_phy_eq_setting_finder(dw_dev, acq,
+						&ch0, &ch1, &ch2)) {
+				if (dw_phy_eq_maxvsmin(ch0.best_setting,
+							ch1.best_setting,
+							ch2.best_setting,
+							min_max_length))
+					break;
+			}
+
+			ch0.best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+			ch1.best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+			ch2.best_setting = PHY_EQ_ERROR_CABLE_SETTING;
+		}
+
+		dev_dbg(dw_dev->dev, "equalizer settings: "
+				"ch0=0x%x, ch1=0x%x, ch1=0x%x\n",
+				ch0.best_setting, ch1.best_setting,
+				ch2.best_setting);
+
+		if (i == PHY_EQ_MINMAX_NTRIES)
+			ret = -EINVAL;
+
+		lock_vector = 0x1;
+		lock_vector <<= ch0.best_setting;
+		dw_phy_eq_equal_setting_ch0(dw_dev, lock_vector);
+
+		lock_vector = 0x1;
+		lock_vector <<= ch1.best_setting;
+		dw_phy_eq_equal_setting_ch1(dw_dev, lock_vector);
+
+		lock_vector = 0x1;
+		lock_vector <<= ch2.best_setting;
+		dw_phy_eq_equal_setting_ch2(dw_dev, lock_vector);
+
+		phy_pddq(dw_dev, 1);
+		phy_pddq(dw_dev, 0);
+	}
+
+	return ret;
+}
+
+static int dw_phy_config(struct dw_phy_dev *dw_dev, unsigned char color_depth,
+		bool hdmi2, bool scrambling)
+{
+	const struct dw_phy_mpll_config *mpll_cfg = dw_phy_e405_mpll_cfg;
+	struct device *dev = dw_dev->dev;
+	int timeout = 100;
+	u16 val, res_idx;
+	bool zcal_done;
+
+	dev_dbg(dev, "%s: color_depth=%d, hdmi2=%d, scrambling=%d, cfg_clk=%d\n",
+			__func__, color_depth, hdmi2, scrambling, dw_dev->cfg_clk);
+
+	switch (color_depth) {
+	case 8:
+		res_idx = 0x0;
+		break;
+	case 10:
+		res_idx = 0x1;
+		break;
+	case 12:
+		res_idx = 0x2;
+		break;
+	case 16:
+		res_idx = 0x3;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	phy_reset(dw_dev, 1);
+	phy_pddq(dw_dev, 1);
+	phy_svsmode(dw_dev, 1);
+
+	phy_zcal_reset(dw_dev);
+	do {
+		usleep_range(1000, 1100);
+		zcal_done = phy_zcal_done(dw_dev);
+	} while (!zcal_done && timeout--);
+
+	if (!zcal_done) {
+		dev_err(dw_dev->dev, "Zcal calibration failed\n");
+		return -ETIMEDOUT;
+	}
+
+	phy_reset(dw_dev, 0);
+
+	/* CMU */
+	val = (0x08 << 10) | (0x01 << 9);
+	val |= (dw_dev->cfg_clk * 4) & GENMASK(8, 0);
+	phy_write(dw_dev, val, PHY_CMU_CONFIG);
+
+	/* Color Depth and enable fast switching */
+	val = phy_read(dw_dev, PHY_SYSTEM_CONFIG);
+	val = (val & ~0x60) | (res_idx << 5) | BIT(11);
+	phy_write(dw_dev, val, PHY_SYSTEM_CONFIG);
+
+	/* MPLL */
+	for (; mpll_cfg->addr != 0x0; mpll_cfg++)
+		phy_write(dw_dev, mpll_cfg->val, mpll_cfg->addr);
+
+	/* Operation for data rates between 3.4Gbps and 6Gbps */
+	val = phy_read(dw_dev, PHY_CDR_CTRL_CNT);
+	if (hdmi2)
+		val |= BIT(8);
+	else
+		val &= ~BIT(8);
+	phy_write(dw_dev, val, PHY_CDR_CTRL_CNT);
+
+	/* Scrambling */
+	val = phy_read(dw_dev, PHY_OVL_PROT_CTRL);
+	if (scrambling)
+		val |= GENMASK(7,6);
+	else
+		val &= ~GENMASK(7,6);
+	phy_write(dw_dev, val, PHY_OVL_PROT_CTRL);
+
+	/* Enable phy */
+	phy_pddq(dw_dev, 0);
+
+	dw_dev->color_depth = color_depth;
+	dw_dev->hdmi2 = hdmi2;
+	dw_dev->scrambling = scrambling;
+	return 0;
+}
+
+static int dw_phy_enable(struct dw_phy_dev *dw_dev, unsigned char color_depth,
+		bool hdmi2, bool scrambling)
+{
+	int ret;
+
+	if (dw_dev->phy_enabled &&
+	    dw_dev->color_depth == color_depth &&
+	    dw_dev->hdmi2 == hdmi2 &&
+	    dw_dev->scrambling == scrambling)
+		return 0;
+
+	ret = dw_phy_config(dw_dev, color_depth, hdmi2, scrambling);
+	if (ret)
+		return ret;
+
+	phy_reset(dw_dev, 0);
+	phy_pddq(dw_dev, 0);
+	dw_dev->phy_enabled = true;
+	return 0;
+}
+
+static void dw_phy_disable(struct dw_phy_dev *dw_dev)
+{
+	if (!dw_dev->phy_enabled)
+		return;
+
+	phy_reset(dw_dev, 1);
+	phy_pddq(dw_dev, 1);
+	phy_svsmode(dw_dev, 0);
+	dw_dev->mpll_status = 0xFFFF;
+	dw_dev->phy_enabled = false;
+}
+
+static long dw_phy_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
+{
+	struct dw_phy_dev *dw_dev = to_dw_dev(sd);
+	struct dw_phy_config_command *ccmd;
+	struct dw_phy_eq_command *ecmd;
+	int ret = 0;
+
+	dev_dbg(dw_dev->dev, "%s: cmd=%d\n", __func__, cmd);
+
+	mutex_lock(&dw_dev->lock);
+	switch (cmd) {
+	case DW_PHY_IOCTL_EQ_INIT:
+		ecmd = (struct dw_phy_eq_command *)arg; 
+		ecmd->result = dw_phy_eq_init(dw_dev, ecmd->nacq, ecmd->force);
+		break;
+	case DW_PHY_IOCTL_CONFIG:
+		ccmd = (struct dw_phy_config_command *)arg;
+		ccmd->result = dw_phy_enable(dw_dev, ccmd->color_depth,
+				ccmd->hdmi2, ccmd->scrambling);
+		break;
+	default:
+		ret = -ENOIOCTLCMD;
+		break;
+	}
+	mutex_unlock(&dw_dev->lock);
+
+	return ret;
+}
+
+static int dw_phy_s_power(struct v4l2_subdev *sd, int on)
+{
+	struct dw_phy_dev *dw_dev = to_dw_dev(sd);
+
+	dev_dbg(dw_dev->dev, "%s: on=%d\n", __func__, on);
+
+	mutex_lock(&dw_dev->lock);
+	if (!on)
+		dw_phy_disable(dw_dev);
+	mutex_unlock(&dw_dev->lock);
+	return 0;
+}
+
+static const struct v4l2_subdev_core_ops dw_phy_core_ops = {
+	.ioctl = dw_phy_ioctl,
+	.s_power = dw_phy_s_power,
+};
+
+static const struct v4l2_subdev_ops dw_phy_sd_ops = {
+	.core = &dw_phy_core_ops,
+};
+
+struct dw_hdmi_phy_data {
+	const char *name;
+	unsigned int version;
+};
+
+static const struct dw_hdmi_phy_data dw_phy_e405_data = {
+	.name = "e405",
+	.version = 405,
+};
+
+static int dw_phy_probe(struct platform_device *pdev)
+{
+	struct dw_phy_pdata *pdata = pdev->dev.platform_data;
+	const struct dw_hdmi_phy_data *of_data;
+	struct device *dev = &pdev->dev;
+	struct dw_phy_dev *dw_dev;
+	struct v4l2_subdev *sd;
+	int ret;
+
+	dev_dbg(dev, "probe start\n");
+
+	dw_dev = devm_kzalloc(dev, sizeof(*dw_dev), GFP_KERNEL);
+	if (!dw_dev)
+		return -ENOMEM;
+
+	if (!pdata) {
+		dev_err(dev, "no platform data suplied\n");
+		return -EINVAL;
+	}
+
+	of_data = of_device_get_match_data(dev);
+	if (!of_data) {
+		dev_err(dev, "no valid phy configuration available\n");
+		return -EINVAL;
+	}
+
+	dw_dev->dev = dev;
+	dw_dev->config = pdata;
+	dw_dev->version = of_data->version;
+	mutex_init(&dw_dev->lock);
+
+	dw_dev->clk = devm_clk_get(dev, "cfg");
+	if (IS_ERR(dw_dev->clk)) {
+		dev_err(dev, "failed to get cfg clock\n");
+		return PTR_ERR(dw_dev->clk);
+	}
+
+	ret = clk_prepare_enable(dw_dev->clk);
+	if (ret) {
+		dev_err(dev, "failed to enable cfg clock\n");
+		return ret;
+	}
+
+	dw_dev->cfg_clk = clk_get_rate(dw_dev->clk) / 1000000U;
+	if (!dw_dev->cfg_clk) {
+		dev_err(dev, "invalid cfg clock frequency\n");
+		ret = -EINVAL;
+		goto err_clk;
+	}
+
+	/* V4L2 initialization */
+	sd = &dw_dev->sd;
+	v4l2_subdev_init(sd, &dw_phy_sd_ops);
+	strlcpy(sd->name, dev_name(dev), sizeof(sd->name));
+	sd->dev = dev;
+
+	/* Force phy disabling */
+	dw_dev->phy_enabled = true;
+	dw_phy_disable(dw_dev);
+
+	ret = v4l2_async_register_subdev(sd);
+	if (ret) {
+		dev_err(dev, "failed to register subdev\n");
+		goto err_clk;
+	}
+
+	dev_set_drvdata(dev, sd);
+	dev_dbg(dev, "driver probed (name=%s, cfg clock=%d)\n",
+			of_data->name, dw_dev->cfg_clk);
+	return 0;
+
+err_clk:
+	clk_disable_unprepare(dw_dev->clk);
+	return ret;
+}
+
+static int dw_phy_remove(struct platform_device *pdev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(&pdev->dev);
+	struct dw_phy_dev *dw_dev = to_dw_dev(sd);
+
+	v4l2_async_unregister_subdev(sd);
+	clk_disable_unprepare(dw_dev->clk);
+	return 0;
+}
+
+static const struct of_device_id dw_hdmi_phy_e405_id[] = {
+	{ .compatible = "snps,dw-hdmi-phy-e405", .data = &dw_phy_e405_data, },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, dw_hdmi_phy_e405_id);
+
+static struct platform_driver dw_phy_e405_driver = {
+	.probe = dw_phy_probe,
+	.remove = dw_phy_remove,
+	.driver = {
+		.name = DW_PHY_E405_DRVNAME,
+		.of_match_table = dw_hdmi_phy_e405_id,
+	}
+};
+module_platform_driver(dw_phy_e405_driver);
diff --git a/drivers/media/platform/dwc/dw-hdmi-phy-e405.h b/drivers/media/platform/dwc/dw-hdmi-phy-e405.h
new file mode 100644
index 0000000..3e6c8da
--- /dev/null
+++ b/drivers/media/platform/dwc/dw-hdmi-phy-e405.h
@@ -0,0 +1,63 @@
+/*
+ * Synopsys Designware HDMI PHY E405 driver
+ *
+ * This Synopsys dw-phy-e405 software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS"  WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DW_HDMI_PHY_E405_H__
+#define __DW_HDMI_PHY_E405_H__
+
+#define PHY_CMU_CONFIG				0x02
+#define PHY_SYSTEM_CONFIG			0x03
+#define PHY_MAINFSM_CTRL			0x05
+#define PHY_MAINFSM_OVR2			0x08
+#define PHY_MAINFSM_STATUS1			0x09
+#define PHY_OVL_PROT_CTRL			0x0D
+#define PHY_CDR_CTRL_CNT			0x0E
+#define PHY_CLK_MPLL_STATUS			0x2F
+#define PHY_CH0_EQ_CTRL1			0x32
+#define PHY_CH0_EQ_CTRL2			0x33
+#define PHY_CH0_EQ_STATUS			0x34
+#define PHY_CH0_EQ_CTRL3			0x3E
+#define PHY_CH0_EQ_CTRL4			0x3F
+#define PHY_CH0_EQ_STATUS2			0x40
+#define PHY_CH0_EQ_STATUS3			0x42
+#define PHY_CH0_EQ_CTRL6			0x43
+#define PHY_CH1_EQ_CTRL1			0x52
+#define PHY_CH1_EQ_CTRL2			0x53
+#define PHY_CH1_EQ_STATUS			0x54
+#define PHY_CH1_EQ_CTRL3			0x5E
+#define PHY_CH1_EQ_CTRL4			0x5F
+#define PHY_CH1_EQ_STATUS2			0x60
+#define PHY_CH1_EQ_STATUS3			0x62
+#define PHY_CH1_EQ_CTRL6			0x63
+#define PHY_CH2_EQ_CTRL1			0x72
+#define PHY_CH2_EQ_CTRL2			0x73
+#define PHY_CH2_EQ_STATUS			0x74
+#define PHY_CH2_EQ_CTRL3			0x7E
+#define PHY_CH2_EQ_CTRL4			0x7F
+#define PHY_CH2_EQ_STATUS2			0x80
+#define PHY_CH2_EQ_STATUS3			0x82
+#define PHY_CH2_EQ_CTRL6			0x83
+
+#endif /* __DW_HDMI_PHY_E405_H__ */
diff --git a/include/media/dwc/dw-hdmi-phy-pdata.h b/include/media/dwc/dw-hdmi-phy-pdata.h
new file mode 100644
index 0000000..e533eec
--- /dev/null
+++ b/include/media/dwc/dw-hdmi-phy-pdata.h
@@ -0,0 +1,128 @@
+/*
+ * Synopsys Designware HDMI PHY platform data
+ *
+ * This Synopsys dw-hdmi-phy software and associated documentation
+ * (hereinafter the "Software") is an unsupported proprietary work of
+ * Synopsys, Inc. unless otherwise expressly agreed to in writing between
+ * Synopsys and you. The Software IS NOT an item of Licensed Software or a
+ * Licensed Product under any End User Software License Agreement or
+ * Agreement for Licensed Products with Synopsys or any supplement thereto.
+ * Synopsys is a registered trademark of Synopsys, Inc. Other names included
+ * in the SOFTWARE may be the trademarks of their respective owners.
+ *
+ * The contents of this file are dual-licensed; you may select either version 2
+ * of the GNU General Public License (“GPL”) or the MIT license (“MIT”).
+ *
+ * Copyright (c) 2017 Synopsys, Inc. and/or its affiliates.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS"  WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING, BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT, OR OTHERWISE
+ * ARISING FROM, OUT OF, OR IN CONNECTION WITH THE SOFTWARE THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DW_HDMI_PHY_PDATA_H__
+#define __DW_HDMI_PHY_PDATA_H__
+
+#define DW_PHY_E405_DRVNAME	"dw-hdmi-phy-e405"
+
+#define DW_PHY_IOCTL_EQ_INIT		_IOW('R',1,int)
+#define DW_PHY_IOCTL_CONFIG		_IOW('R',2,int)
+
+/**
+ * struct dw_phy_eq_command - Command arguments for HDMI PHY equalizer
+ * 	algorithm.
+ *
+ * @nacq: Number of acquisitions to get.
+ *
+ * @force: Force equalizer algorithm even if the MPLL status didn't change
+ * from previous run.
+ *
+ * @result: Result from the equalizer algorithm. Shall be zero if equalizer
+ * ran with success or didn't run because the video mode does not need
+ * equalizer (for low clock values).
+ */
+struct dw_phy_eq_command {
+	u16 nacq;
+	bool force;
+	int result;
+};
+
+/**
+ * struct dw_phy_config_command - Command arguments for HDMI PHY configuration
+ * function.
+ *
+ * @color_depth: Color depth of the video mode being received.
+ *
+ * @hdmi2: Must be set to true if the video mode being received has a data
+ * rate above 3.4Gbps (generally HDMI 2.0 video modes, like 4k@60Hz).
+ *
+ * @scrambling: Must be set to true if scrambling is currently enabled.
+ * Scrambling is enabled by source when SCDC scrambling_en field is set to 1.
+ *
+ * @result: Result from the configuration function. Shall be zero if phy was
+ * configured with success.
+ */
+struct dw_phy_config_command {
+	unsigned char color_depth;
+	bool hdmi2;
+	bool scrambling;
+	int result;
+};
+
+/**
+ * struct dw_phy_funcs - Set of callbacks used to communicate between phy
+ * 	and hdmi controller. Controller must correctly fill these callbacks
+ * 	before probbing the phy driver.
+ *
+ * @write: write callback. Write value 'val' into address 'addr' of phy.
+ *
+ * @read: read callback. Read address 'addr' and return the value.
+ *
+ * @reset: reset callback. Activate phy reset. Active high.
+ *
+ * @pddq: pddq callback. Activate phy configuration mode. Active high.
+ *
+ * @svsmode: svsmode callback. Activate phy retention mode. Active low.
+ *
+ * @zcal_reset: zcal reset callback. Restart the impedance calibration
+ * procedure. Active high. This is only used in prototyping and not in real
+ * ASIC. Callback shall be empty (but non NULL) in ASIC cases.
+ *
+ * @zcal_done: zcal done callback. Return the current status of impedance
+ * calibration procedure. This is only used in prototyping and not in real
+ * ASIC. Shall return always true in ASIC cases.
+ *
+ * @tmds_valid: TMDS valid callback. Return the current status of TMDS signal
+ * that comes from phy and feeds controller. This is read from a controller
+ * register.
+ */
+struct dw_phy_funcs {
+	void (*write) (void *arg, u16 val, u16 addr);
+	u16 (*read) (void *arg, u16 addr);
+	void (*reset) (void *arg, int enable);
+	void (*pddq) (void *arg, int enable);
+	void (*svsmode) (void *arg, int enable);
+	void (*zcal_reset) (void *arg);
+	bool (*zcal_done) (void *arg);
+	bool (*tmds_valid) (void *arg);
+};
+
+/**
+ * struct dw_phy_pdata - Platform data definition for Synopsys HDMI PHY.
+ *
+ * @funcs: set of callbacks that must be correctly filled and supplied to phy.
+ * See @dw_phy_funcs.
+ *
+ * @funcs_arg: parameter that is supplied to callbacks along with the function
+ * parameters.
+ */
+struct dw_phy_pdata {
+	const struct dw_phy_funcs *funcs;
+	void *funcs_arg;
+};
+
+#endif /* __DW_HDMI_PHY_PDATA_H__ */
-- 
1.9.1

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web