Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1625818 > unrolled thread

[PATCH 4/4] ARM: sun8i: h3: bananapi-m2-plus: Enable USB OTG

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  [PATCH 4/4] ARM: sun8i: h3: bananapi-m2-plus: Enable USB OTG Chen-Yu Tsai <wens@csie.org> - 2017-04-19 07:20 +0200

#1625818 — [PATCH 4/4] ARM: sun8i: h3: bananapi-m2-plus: Enable USB OTG

The Bananapi M2 Plus has a USB OTG port that can be used in both
powered host mode and peripheral mode. When in peripheral mode,
the port does not power the board. There is no VBUS sensing on
the port.

This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index 52acbe111cad..17c7c088cdea 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -92,6 +92,10 @@
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -145,6 +149,10 @@
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
@@ -170,6 +178,11 @@
 	};
 };
 
+&reg_usb0_vbus {
+	gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
@@ -182,7 +195,14 @@
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
-	/* USB VBUS is on as long as VCC-IO is on */
+	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* USB host VBUS is on as long as VCC-IO is on */
 	status = "okay";
 };
-- 
2.11.0

[toc] | [standalone]

Back to top | Article view | linux.kernel

csiph-web