Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1625819 > unrolled thread

[PATCH 3/4] ARM: sun8i: h3: orangepi-pc: Enable USB OTG

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  [PATCH 3/4] ARM: sun8i: h3: orangepi-pc: Enable USB OTG Chen-Yu Tsai <wens@csie.org> - 2017-04-19 07:20 +0200

#1625819 — [PATCH 3/4] ARM: sun8i: h3: orangepi-pc: Enable USB OTG

The Orange Pi PC, PC Plus, and Plus 2E all have a USB OTG port
that can be used in both powered host mode and peripheral mode.
When in peripheral mode, the port does not power the board.
There is no VBUS sensing on the port. All three boards have all
related pins routed the same way.

The device tree file for the Orange Pi Plus 2E is based on the
Orange Pi PC Plus, which itself is based on the Orange Pi PC.
Changes to the base Orange Pi PC device tree file affects all 3
boards.

This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index f148111c326d..1a044b17d6c6 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -97,6 +97,10 @@
 	status = "okay";
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -125,6 +129,10 @@
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
@@ -156,6 +164,11 @@
 	};
 };
 
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
@@ -180,7 +193,14 @@
 	status = "disabled";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
-	/* USB VBUS is always on */
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* VBUS on USB host ports are always on */
 	status = "okay";
 };
-- 
2.11.0

[toc] | [standalone]

Back to top | Article view | linux.kernel

csiph-web