Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1513252 > unrolled thread

[PATCH v3 0/2] backlight: pwm_bl: Fix the initial power state selection

Back to article view | Back to linux.kernel

Contents

  [PATCH v3 0/2] backlight: pwm_bl: Fix the initial power state selection Peter Ujfalusi <peter.ujfalusi@ti.com> - 2016-11-01 14:00 +0100
    [PATCH v3 2/2] backlight: pwm_bl: Check the pwm state for initial backlight power state Peter Ujfalusi <peter.ujfalusi@ti.com> - 2016-11-01 14:10 +0100
      Re: [PATCH v3 2/2] backlight: pwm_bl: Check the pwm state for  initial backlight power state Philipp Zabel <p.zabel@pengutronix.de> - 2016-11-01 14:20 +0100
    [PATCH v3 1/2] backlight: pwm_bl: Move the checks for initial power state to a separate function Peter Ujfalusi <peter.ujfalusi@ti.com> - 2016-11-01 14:10 +0100
      Re: [PATCH v3 1/2] backlight: pwm_bl: Move the checks for initial  power state to a separate function Philipp Zabel <p.zabel@pengutronix.de> - 2016-11-01 14:20 +0100

#1513252 — [PATCH v3 0/2] backlight: pwm_bl: Fix the initial power state selection

Hi,

Changes since v2:
- Do not change the way how the GPIO initially configured as input is handled.
  Configure it as output and set it's state as active.

Changes since v1:
- Handling of the enable GPIO is reworked:
 - Only change direction to output when the pin was input and in this case set
   the GPIO line physical low
 - With this change we can ensure that the enable GPIO is output so we do not
   need to check the direction of it later on.

Cover letter:

3698d7e7d221 backlight: pwm_bl: Avoid backlight flicker when probed from DT

added support for avoiding backlight flickering, which in essence was designed
to not enable the baclkight when the driver loads, but let the user of the
backlight to enable it later on.

There are boards (like am437x-gp-evm) where we do not have valid GPIO to enable
the backlight (TPS61081DRC's EN pin is connected to V3_3D) and the regulator
is always on (VBAT in case of the gp-evm). In this board the logic to check the
GPIO state and the regulator is failing and the backlight will be enabled as
soon as the pwm_bl driver is loaded.

By extending the check to look at the PWM state this issue can be avoided and
the backlight will be enabled only when it's user is asking it to be enabled.

Regards,
Peter
---
Peter Ujfalusi (2):
  backlight: pwm_bl: Move the checks for initial power state to a
    separate function
  backlight: pwm_bl: Check the pwm state for initial backlight power
    state

 drivers/video/backlight/pwm_bl.c | 57 ++++++++++++++++++++++++++--------------
 1 file changed, 38 insertions(+), 19 deletions(-)

-- 
2.10.2

[toc] | [next] | [standalone]

#1513258 — [PATCH v3 2/2] backlight: pwm_bl: Check the pwm state for initial backlight power state

If the pwm is not enabled the backlight initially should not be enabled
either if we have booted with DT and there is a phandle pointing to the
backlight node.

The patch extends the checks to decide if we should keep the backlight off
initially.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
---
 drivers/video/backlight/pwm_bl.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
index 4b07da278b4f..f680f7b033b2 100644
--- a/drivers/video/backlight/pwm_bl.c
+++ b/drivers/video/backlight/pwm_bl.c
@@ -215,6 +215,10 @@ static int pwm_backlight_initial_power_state(const struct pwm_bl_data *pb)
 	if (!regulator_is_enabled(pb->power_supply))
 		return FB_BLANK_POWERDOWN;
 
+	/* The pwm is disabled, keep it like this */
+	if (!pwm_is_enabled(pb->pwm))
+		return FB_BLANK_POWERDOWN;
+
 	return FB_BLANK_UNBLANK;
 }
 
-- 
2.10.2

[toc] | [prev] | [next] | [standalone]

#1513265 — Re: [PATCH v3 2/2] backlight: pwm_bl: Check the pwm state for initial backlight power state

Am Dienstag, den 01.11.2016, 14:59 +0200 schrieb Peter Ujfalusi:
> If the pwm is not enabled the backlight initially should not be enabled
> either if we have booted with DT and there is a phandle pointing to the
> backlight node.
> 
> The patch extends the checks to decide if we should keep the backlight off
> initially.
> 
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

regards
Philipp

[toc] | [prev] | [next] | [standalone]

#1513262 — [PATCH v3 1/2] backlight: pwm_bl: Move the checks for initial power state to a separate function

Move the checks to select the initial state for the backlight to a new
function and document the checks we are doing.

With the separate function it is going to be easier to fix or improve the
initial power state configuration later and it is easier to read the code.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
---
 drivers/video/backlight/pwm_bl.c | 53 ++++++++++++++++++++++++++--------------
 1 file changed, 34 insertions(+), 19 deletions(-)

diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
index 12614006211e..4b07da278b4f 100644
--- a/drivers/video/backlight/pwm_bl.c
+++ b/drivers/video/backlight/pwm_bl.c
@@ -192,6 +192,32 @@ static int pwm_backlight_parse_dt(struct device *dev,
 }
 #endif
 
+static int pwm_backlight_initial_power_state(const struct pwm_bl_data *pb)
+{
+	struct device_node *node = pb->dev->of_node;
+
+	/* Not booted with device tree or no phandle link to the node */
+	if (!node || !node->phandle)
+		return FB_BLANK_UNBLANK;
+
+	/*
+	 * If the driver is probed from the device tree and there is a
+	 * phandle link pointing to the backlight node, it is safe to
+	 * assume that another driver will enable the backlight at the
+	 * appropriate time. Therefore, if it is disabled, keep it so.
+	 */
+
+	/* if the enable GPIO is disabled, do not enable the backlight */
+	if (pb->enable_gpio && gpiod_get_value(pb->enable_gpio) == 0)
+		return FB_BLANK_POWERDOWN;
+
+	/* The regulator is disabled, do not enable the backlight */
+	if (!regulator_is_enabled(pb->power_supply))
+		return FB_BLANK_POWERDOWN;
+
+	return FB_BLANK_UNBLANK;
+}
+
 static int pwm_backlight_probe(struct platform_device *pdev)
 {
 	struct platform_pwm_backlight_data *data = dev_get_platdata(&pdev->dev);
@@ -200,7 +226,6 @@ static int pwm_backlight_probe(struct platform_device *pdev)
 	struct backlight_device *bl;
 	struct device_node *node = pdev->dev.of_node;
 	struct pwm_bl_data *pb;
-	int initial_blank = FB_BLANK_UNBLANK;
 	struct pwm_args pargs;
 	int ret;
 
@@ -267,20 +292,13 @@ static int pwm_backlight_probe(struct platform_device *pdev)
 		pb->enable_gpio = gpio_to_desc(data->enable_gpio);
 	}
 
-	if (pb->enable_gpio) {
-		/*
-		 * If the driver is probed from the device tree and there is a
-		 * phandle link pointing to the backlight node, it is safe to
-		 * assume that another driver will enable the backlight at the
-		 * appropriate time. Therefore, if it is disabled, keep it so.
-		 */
-		if (node && node->phandle &&
-		    gpiod_get_direction(pb->enable_gpio) == GPIOF_DIR_OUT &&
-		    gpiod_get_value(pb->enable_gpio) == 0)
-			initial_blank = FB_BLANK_POWERDOWN;
-		else
-			gpiod_direction_output(pb->enable_gpio, 1);
-	}
+	/*
+	 * If the GPIO is configured as input, change the direction to output
+	 * and set the GPIO as active.
+	 */
+	if (pb->enable_gpio &&
+	    gpiod_get_direction(pb->enable_gpio) == GPIOF_DIR_IN)
+		gpiod_direction_output(pb->enable_gpio, 1);
 
 	pb->power_supply = devm_regulator_get(&pdev->dev, "power");
 	if (IS_ERR(pb->power_supply)) {
@@ -288,9 +306,6 @@ static int pwm_backlight_probe(struct platform_device *pdev)
 		goto err_alloc;
 	}
 
-	if (node && node->phandle && !regulator_is_enabled(pb->power_supply))
-		initial_blank = FB_BLANK_POWERDOWN;
-
 	pb->pwm = devm_pwm_get(&pdev->dev, NULL);
 	if (IS_ERR(pb->pwm) && PTR_ERR(pb->pwm) != -EPROBE_DEFER && !node) {
 		dev_err(&pdev->dev, "unable to request PWM, trying legacy API\n");
@@ -347,7 +362,7 @@ static int pwm_backlight_probe(struct platform_device *pdev)
 	}
 
 	bl->props.brightness = data->dft_brightness;
-	bl->props.power = initial_blank;
+	bl->props.power = pwm_backlight_initial_power_state(pb);
 	backlight_update_status(bl);
 
 	platform_set_drvdata(pdev, bl);
-- 
2.10.2

[toc] | [prev] | [next] | [standalone]

#1513264 — Re: [PATCH v3 1/2] backlight: pwm_bl: Move the checks for initial power state to a separate function

Am Dienstag, den 01.11.2016, 14:59 +0200 schrieb Peter Ujfalusi:
> Move the checks to select the initial state for the backlight to a new
> function and document the checks we are doing.
> 
> With the separate function it is going to be easier to fix or improve the
> initial power state configuration later and it is easier to read the code.
> 
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>

regards
Philipp

> ---
>  drivers/video/backlight/pwm_bl.c | 53 ++++++++++++++++++++++++++--------------
>  1 file changed, 34 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
> index 12614006211e..4b07da278b4f 100644
> --- a/drivers/video/backlight/pwm_bl.c
> +++ b/drivers/video/backlight/pwm_bl.c
> @@ -192,6 +192,32 @@ static int pwm_backlight_parse_dt(struct device *dev,
>  }
>  #endif
>  
> +static int pwm_backlight_initial_power_state(const struct pwm_bl_data *pb)
> +{
> +	struct device_node *node = pb->dev->of_node;
> +
> +	/* Not booted with device tree or no phandle link to the node */
> +	if (!node || !node->phandle)
> +		return FB_BLANK_UNBLANK;
> +
> +	/*
> +	 * If the driver is probed from the device tree and there is a
> +	 * phandle link pointing to the backlight node, it is safe to
> +	 * assume that another driver will enable the backlight at the
> +	 * appropriate time. Therefore, if it is disabled, keep it so.
> +	 */
> +
> +	/* if the enable GPIO is disabled, do not enable the backlight */
> +	if (pb->enable_gpio && gpiod_get_value(pb->enable_gpio) == 0)
> +		return FB_BLANK_POWERDOWN;
> +
> +	/* The regulator is disabled, do not enable the backlight */
> +	if (!regulator_is_enabled(pb->power_supply))
> +		return FB_BLANK_POWERDOWN;
> +
> +	return FB_BLANK_UNBLANK;
> +}
> +
>  static int pwm_backlight_probe(struct platform_device *pdev)
>  {
>  	struct platform_pwm_backlight_data *data = dev_get_platdata(&pdev->dev);
> @@ -200,7 +226,6 @@ static int pwm_backlight_probe(struct platform_device *pdev)
>  	struct backlight_device *bl;
>  	struct device_node *node = pdev->dev.of_node;
>  	struct pwm_bl_data *pb;
> -	int initial_blank = FB_BLANK_UNBLANK;
>  	struct pwm_args pargs;
>  	int ret;
>  
> @@ -267,20 +292,13 @@ static int pwm_backlight_probe(struct platform_device *pdev)
>  		pb->enable_gpio = gpio_to_desc(data->enable_gpio);
>  	}
>  
> -	if (pb->enable_gpio) {
> -		/*
> -		 * If the driver is probed from the device tree and there is a
> -		 * phandle link pointing to the backlight node, it is safe to
> -		 * assume that another driver will enable the backlight at the
> -		 * appropriate time. Therefore, if it is disabled, keep it so.
> -		 */
> -		if (node && node->phandle &&
> -		    gpiod_get_direction(pb->enable_gpio) == GPIOF_DIR_OUT &&
> -		    gpiod_get_value(pb->enable_gpio) == 0)
> -			initial_blank = FB_BLANK_POWERDOWN;
> -		else
> -			gpiod_direction_output(pb->enable_gpio, 1);
> -	}
> +	/*
> +	 * If the GPIO is configured as input, change the direction to output
> +	 * and set the GPIO as active.
> +	 */
> +	if (pb->enable_gpio &&
> +	    gpiod_get_direction(pb->enable_gpio) == GPIOF_DIR_IN)
> +		gpiod_direction_output(pb->enable_gpio, 1);
>  
>  	pb->power_supply = devm_regulator_get(&pdev->dev, "power");
>  	if (IS_ERR(pb->power_supply)) {
> @@ -288,9 +306,6 @@ static int pwm_backlight_probe(struct platform_device *pdev)
>  		goto err_alloc;
>  	}
>  
> -	if (node && node->phandle && !regulator_is_enabled(pb->power_supply))
> -		initial_blank = FB_BLANK_POWERDOWN;
> -
>  	pb->pwm = devm_pwm_get(&pdev->dev, NULL);
>  	if (IS_ERR(pb->pwm) && PTR_ERR(pb->pwm) != -EPROBE_DEFER && !node) {
>  		dev_err(&pdev->dev, "unable to request PWM, trying legacy API\n");
> @@ -347,7 +362,7 @@ static int pwm_backlight_probe(struct platform_device *pdev)
>  	}
>  
>  	bl->props.brightness = data->dft_brightness;
> -	bl->props.power = initial_blank;
> +	bl->props.power = pwm_backlight_initial_power_state(pb);
>  	backlight_update_status(bl);
>  
>  	platform_set_drvdata(pdev, bl);

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web