Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]
Groups > linux.kernel > #1497225 > unrolled thread
| Started by | Pantelis Antoniou <pantelis.antoniou@konsulko.com> |
|---|---|
| First post | 2016-10-07 17:30 +0200 |
| Last post | 2016-10-10 21:50 +0200 |
| Articles | 2 — 2 participants |
Back to article view | Back to linux.kernel
This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by
below is the oldest one visible, not the original post.
[PATCH 02/10] mfd: sam: Add documentation for the SAM FPGA Pantelis Antoniou <pantelis.antoniou@konsulko.com> - 2016-10-07 17:30 +0200
Re: [PATCH 02/10] mfd: sam: Add documentation for the SAM FPGA Rob Herring <robh@kernel.org> - 2016-10-10 21:50 +0200
| From | Pantelis Antoniou <pantelis.antoniou@konsulko.com> |
|---|---|
| Date | 2016-10-07 17:30 +0200 |
| Subject | [PATCH 02/10] mfd: sam: Add documentation for the SAM FPGA |
| Message-ID | <spFfY-2lv-39@gated-at.bofh.it> |
From: Georgi Vlaev <gvlaev@juniper.net>
Add DT bindings document for the SAM MFD device.
Signed-off-by: Georgi Vlaev <gvlaev@juniper.net>
[Ported from Juniper kernel]
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
---
Documentation/devicetree/bindings/mfd/jnx-sam.txt | 94 +++++++++++++++++++++++
1 file changed, 94 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/jnx-sam.txt
diff --git a/Documentation/devicetree/bindings/mfd/jnx-sam.txt b/Documentation/devicetree/bindings/mfd/jnx-sam.txt
new file mode 100644
index 0000000..b4af7ea
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/jnx-sam.txt
@@ -0,0 +1,94 @@
+Device-Tree bindings for Juniper Networks SAM MFD
+
+Required properties:
+
+- compatible - Must be: "jnx,sam"
+
+Optional properties:
+
+- pma-coefficients: A set of tupples containing the configuration of the PMA.
+
+Device Description
+------ -----------
+jnx,i2c-sam : I2C mux driver
+jnx,gpio-sam : GPIO block
+jnx,flash-sam : MTD Flash
+jnx,mdio-sam : MDIO interfaces
+
+All these optional nodes are described in their respective binding
+documents.
+
+Example node:
+
+pci-0000-10-00.0 {
+ compatible = "jnx,sam";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pma-coefficients = <4 0x0>;
+
+ i2c-sam@10 {
+ compatible = "jnx,i2c-sam";
+ mux-channels = <2>;
+ master-offset = <0x10000>;
+ };
+
+ gpiogpqam0: gpio-sam@10 {
+ compatible = "jnx,gpio-sam";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-count = <297>;
+ interrupt-controller;
+ /*
+ * 1st cell: gpio interrupt status bit
+ * 2nd cell: 1st pin
+ * 3rd cell: # of pins
+ */
+ gpio-interrupts =
+ <0 0 12>, /* phy_int_monitor_en [16] */
+ <1 235 24>, /* qsfpp_fpga_int_monitor [17] */
+ <2 259 24>, /* qsfpp_fpga_modprs_monitor [18] */
+ <3 295 1>, /* si5345_fpga_monitor [19] */
+ <4 294 1>; /* fpc_pic_int_monitor [20] */
+ };
+
+ flash-sam@10 {
+ compatible = "jnx,flash-sam";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ reg = <0x0 0x400000>;
+ label = "pic0-golden";
+ read-only;
+ };
+ partition@400000 {
+ reg = <0x400000 0x400000>;
+ label = "pic0-user";
+ };
+ };
+
+ mdio-sam@10 {
+ compatible = "jnx,mdio-sam";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x40000>;
+
+ /* mii_bus types */
+ mdio0: mdio-sam@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+ };
+
+ mdio1: mdio-sam@4000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4000>;
+ };
+
+ mdio2: mdio-sam@8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x8000>;
+ };
+ };
+};
--
1.9.1
[toc] | [next] | [standalone]
| From | Rob Herring <robh@kernel.org> |
|---|---|
| Date | 2016-10-10 21:50 +0200 |
| Message-ID | <sqOKd-5i6-5@gated-at.bofh.it> |
| In reply to | #1497225 |
On Fri, Oct 07, 2016 at 06:18:30PM +0300, Pantelis Antoniou wrote:
> From: Georgi Vlaev <gvlaev@juniper.net>
>
> Add DT bindings document for the SAM MFD device.
>
> Signed-off-by: Georgi Vlaev <gvlaev@juniper.net>
> [Ported from Juniper kernel]
> Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
> ---
> Documentation/devicetree/bindings/mfd/jnx-sam.txt | 94 +++++++++++++++++++++++
> 1 file changed, 94 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/jnx-sam.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/jnx-sam.txt b/Documentation/devicetree/bindings/mfd/jnx-sam.txt
> new file mode 100644
> index 0000000..b4af7ea
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/jnx-sam.txt
> @@ -0,0 +1,94 @@
> +Device-Tree bindings for Juniper Networks SAM MFD
> +
> +Required properties:
> +
> +- compatible - Must be: "jnx,sam"
Kind of generic. Only 1 FPGA version or some other way to tell the
version?
> +
> +Optional properties:
> +
> +- pma-coefficients: A set of tupples containing the configuration of the PMA.
What's a PMA? What type of configuration? How many entries?
> +Device Description
> +------ -----------
> +jnx,i2c-sam : I2C mux driver
> +jnx,gpio-sam : GPIO block
> +jnx,flash-sam : MTD Flash
> +jnx,mdio-sam : MDIO interfaces
> +
> +All these optional nodes are described in their respective binding
> +documents.
> +
> +Example node:
> +
> +pci-0000-10-00.0 {
What are the numbers?
> + compatible = "jnx,sam";
If this is a PCI device, then it should use PCI compatible string
syntax.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pma-coefficients = <4 0x0>;
> +
> + i2c-sam@10 {
> + compatible = "jnx,i2c-sam";
> + mux-channels = <2>;
> + master-offset = <0x10000>;
> + };
> +
> + gpiogpqam0: gpio-sam@10 {
gpio@...
Where does 10 come from?
> + compatible = "jnx,gpio-sam";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-count = <297>;
> + interrupt-controller;
> + /*
> + * 1st cell: gpio interrupt status bit
> + * 2nd cell: 1st pin
> + * 3rd cell: # of pins
> + */
> + gpio-interrupts =
> + <0 0 12>, /* phy_int_monitor_en [16] */
> + <1 235 24>, /* qsfpp_fpga_int_monitor [17] */
> + <2 259 24>, /* qsfpp_fpga_modprs_monitor [18] */
> + <3 295 1>, /* si5345_fpga_monitor [19] */
> + <4 294 1>; /* fpc_pic_int_monitor [20] */
> + };
> +
> + flash-sam@10 {
> + compatible = "jnx,flash-sam";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@0 {
> + reg = <0x0 0x400000>;
> + label = "pic0-golden";
> + read-only;
> + };
> + partition@400000 {
> + reg = <0x400000 0x400000>;
> + label = "pic0-user";
> + };
> + };
> +
> + mdio-sam@10 {
> + compatible = "jnx,mdio-sam";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x40000>;
> +
> + /* mii_bus types */
> + mdio0: mdio-sam@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0>;
> + };
> +
> + mdio1: mdio-sam@4000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4000>;
> + };
> +
> + mdio2: mdio-sam@8000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x8000>;
> + };
> + };
> +};
> --
> 1.9.1
>
[toc] | [prev] | [standalone]
Back to top | Article view | linux.kernel
csiph-web