Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1366069 > unrolled thread

[PATCH resend v2 7/9] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  [PATCH resend v2 7/9] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators Chen-Yu Tsai <wens@csie.org> - 2016-03-29 11:40 +0200

#1366069 — [PATCH resend v2 7/9] ARM: dts: sun9i: cubieboard4: Add AXP809 PMIC device node and regulators

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 131 +++++++++++++++++++++++++++-
 1 file changed, 129 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index eb2ccd0a3bd5..8d8af1189d87 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -98,7 +98,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
 	cd-inverted;
@@ -108,7 +108,7 @@
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -126,8 +126,135 @@
 
 &r_rsb {
 	status = "okay";
+
+	axp809: pmic@3a3 {
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				/*
+				 * TODO: This should be handled by the
+				 * USB PHY driver.
+				 */
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc33-usbh";
+			};
+
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pb-io-cam";
+			};
+
+			aldo3 {
+				/* unused */
+			};
+
+			reg_dc5ldo: dc5ldo {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpus-09-usbh";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-3v";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-gpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpua";
+			};
+
+			reg_dcdc4: dcdc4 {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-sys-usb0-hdmi";
+			};
+
+			reg_dcdc5: dcdc5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1425000>;
+				regulator-max-microvolt = <1575000>;
+				regulator-name = "vcc-dram";
+			};
+
+			reg_dldo1: dldo1 {
+				/*
+				 * The WiFi chip supports a wide range
+				 * (3.0 ~ 4.8V) of voltages, and so does
+				 * this regulator (3.0 ~ 4.2V), but
+				 * Allwinner SDK always sets it to 3.3V.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-wifi";
+			};
+
+			reg_dldo2: dldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-pl";
+			};
+
+			reg_eldo1: eldo1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vcc-dvdd-cam";
+			};
+
+			reg_eldo2: eldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pe";
+			};
+
+			reg_eldo3: eldo3 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-pm-codec-io1";
+			};
+
+			reg_ldo_io0: ldo_io0 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-pg";
+			};
+
+			reg_ldo_io1: ldo_io1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc-pa-gmac-2v5";
+			};
+
+			reg_rtc_ldo: rtc_ldo {
+				regulator-name = "vcc-rtc-vdd1v8-io";
+			};
+		};
+	};
 };
 
+#include "axp809.dtsi"
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
-- 
2.7.0

[toc] | [standalone]

Back to top | Article view | linux.kernel

csiph-web