Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1424831 > unrolled thread

[PATCH v5 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  [PATCH v5 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver Songjun Wu <songjun.wu@atmel.com> - 2016-06-17 11:10 +0200
    Re: [PATCH v5 2/2] [media] atmel-isc: DT binding for Image Sensor  Controller driver Rob Herring <robh@kernel.org> - 2016-06-20 15:30 +0200

#1424831 — [PATCH v5 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver

DT binding documentation for ISC driver.

Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
---

Changes in v5:
- Add clock names.

Changes in v4:
- Remove the isc clock nodes.

Changes in v3:
- Remove the 'atmel,sensor-preferred'.
- Modify the isc clock node according to the Rob's remarks.

Changes in v2:
- Remove the unit address of the endpoint.
- Add the unit address to the clock node.
- Avoid using underscores in node names.
- Drop the "0x" in the unit address of the i2c node.
- Modify the description of 'atmel,sensor-preferred'.
- Add the description for the ISC internal clock.

 .../devicetree/bindings/media/atmel-isc.txt        | 64 ++++++++++++++++++++++
 1 file changed, 64 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt

diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
new file mode 100644
index 0000000..9558a77
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
@@ -0,0 +1,64 @@
+Atmel Image Sensor Controller (ISC)
+----------------------------------------------
+
+Required properties for ISC:
+- compatible
+	Must be "atmel,sama5d2-isc".
+- reg
+	Physical base address and length of the registers set for the device.
+- interrupts
+	Should contain IRQ line for the ISC.
+- clocks
+	List of clock specifiers, corresponding to entries in
+	the clock-names property;
+	Please refer to clock-bindings.txt.
+- clock-names
+	Required elements: "hclock".
+- #clock-cells
+	Should be 0.
+- clock-output-names
+	Should contain the name of the clock driving the sensor master clock.
+- pinctrl-names, pinctrl-0
+	Please refer to pinctrl-bindings.txt.
+
+ISC supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+isc: isc@f0008000 {
+	compatible = "atmel,sama5d2-isc";
+	reg = <0xf0008000 0x4000>;
+	interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
+	clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
+	clock-names = "hclock", "iscck", "gck";
+	#clock-cells = <0>;
+	clock-output-names = "isc-mck";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
+
+	port {
+		isc_0: endpoint {
+			remote-endpoint = <&ov7740_0>;
+			hsync-active = <1>;
+			vsync-active = <0>;
+			pclk-sample = <1>;
+		};
+	};
+};
+
+i2c1: i2c@fc028000 {
+	ov7740: camera@21 {
+	compatible = "ovti,ov7740";
+	reg = <0x21>;
+	clocks = <&isc>;
+	clock-names = "xvclk";
+	assigned-clocks = <&isc>;
+	assigned-clock-rates = <24000000>;
+
+	port {
+		ov7740_0: endpoint {
+			remote-endpoint = <&isc_0>;
+		};
+	};
+};
-- 
2.7.4

[toc] | [next] | [standalone]

#1426605 — Re: [PATCH v5 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver

On Fri, Jun 17, 2016 at 04:57:14PM +0800, Songjun Wu wrote:
> DT binding documentation for ISC driver.
> 
> Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
> ---
> 
> Changes in v5:
> - Add clock names.
> 
> Changes in v4:
> - Remove the isc clock nodes.
> 
> Changes in v3:
> - Remove the 'atmel,sensor-preferred'.
> - Modify the isc clock node according to the Rob's remarks.
> 
> Changes in v2:
> - Remove the unit address of the endpoint.
> - Add the unit address to the clock node.
> - Avoid using underscores in node names.
> - Drop the "0x" in the unit address of the i2c node.
> - Modify the description of 'atmel,sensor-preferred'.
> - Add the description for the ISC internal clock.
> 
>  .../devicetree/bindings/media/atmel-isc.txt        | 64 ++++++++++++++++++++++
>  1 file changed, 64 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
> new file mode 100644
> index 0000000..9558a77
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
> @@ -0,0 +1,64 @@
> +Atmel Image Sensor Controller (ISC)
> +----------------------------------------------
> +
> +Required properties for ISC:
> +- compatible
> +	Must be "atmel,sama5d2-isc".
> +- reg
> +	Physical base address and length of the registers set for the device.
> +- interrupts
> +	Should contain IRQ line for the ISC.
> +- clocks
> +	List of clock specifiers, corresponding to entries in
> +	the clock-names property;
> +	Please refer to clock-bindings.txt.
> +- clock-names
> +	Required elements: "hclock".

What about the 2 other clocks in the example?

> +- #clock-cells
> +	Should be 0.
> +- clock-output-names
> +	Should contain the name of the clock driving the sensor master clock.

State what the name is.

> +- pinctrl-names, pinctrl-0
> +	Please refer to pinctrl-bindings.txt.
> +
> +ISC supports a single port node with parallel bus. It should contain one
> +'port' child node with child 'endpoint' node. Please refer to the bindings
> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +isc: isc@f0008000 {
> +	compatible = "atmel,sama5d2-isc";
> +	reg = <0xf0008000 0x4000>;
> +	interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
> +	clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
> +	clock-names = "hclock", "iscck", "gck";
> +	#clock-cells = <0>;
> +	clock-output-names = "isc-mck";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
> +
> +	port {
> +		isc_0: endpoint {
> +			remote-endpoint = <&ov7740_0>;
> +			hsync-active = <1>;
> +			vsync-active = <0>;
> +			pclk-sample = <1>;
> +		};
> +	};
> +};
> +
> +i2c1: i2c@fc028000 {
> +	ov7740: camera@21 {
> +	compatible = "ovti,ov7740";

Indentation is still wrong here...

> +	reg = <0x21>;
> +	clocks = <&isc>;
> +	clock-names = "xvclk";
> +	assigned-clocks = <&isc>;
> +	assigned-clock-rates = <24000000>;
> +
> +	port {
> +		ov7740_0: endpoint {
> +			remote-endpoint = <&isc_0>;
> +		};
> +	};
> +};
> -- 
> 2.7.4
> 

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web