Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1235548 > unrolled thread

Re: [PATCH v12 3/5] mtd: nand: vf610_nfc: add device tree bindings

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  Re: [PATCH v12 3/5] mtd: nand: vf610_nfc: add device tree bindings Brian Norris <computersforpeace@gmail.com> - 2015-09-29 23:00 +0200

#1235548 — Re: [PATCH v12 3/5] mtd: nand: vf610_nfc: add device tree bindings

On Wed, Sep 02, 2015 at 06:06:35PM -0700, Stefan Agner wrote:
> Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
> Acked-by: Shawn Guo <shawnguo@kernel.org>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
>  .../devicetree/bindings/mtd/vf610-nfc.txt          | 59 ++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mtd/vf610-nfc.txt
> 
> diff --git a/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
> new file mode 100644
> index 0000000..6be4871
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
> @@ -0,0 +1,59 @@
> +Freescale's NAND flash controller (NFC)
> +
> +This variant of the Freescale NAND flash controller (NFC) can be found on
> +Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70.
> +
> +Required properties:
> +- compatible: Should be set to "fsl,vf610-nfc".
> +- reg: address range of the NFC.
> +- interrupts: interrupt of the NFC.
> +- #address-cells: shall be set to 1. Encode the nand CS.
> +- #size-cells : shall be set to 0.
> +- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
> +- assigned-clock-rates: The NAND bus timing is derived from this clock
> +    rate and should not exceed maximum timing for any NAND memory chip
> +    in a board stuffing. Typical NAND memory timings derived from this
> +    clock are found in the SoC hardware reference manual. Furthermore,
> +    there might be restrictions on maximum rates when using hardware ECC.
> +
> +- #address-cells, #size-cells : Must be present if the device has sub-nodes
> +  representing partitions.
> +
> +Required children nodes:
> +Children nodes represent the available nand chips. Currently the driver can
> +only handle one NAND chip.
> +
> +Required properties:
> +- compatible: Should be set to "fsl,vf610-nfc-cs".
> +- nand-bus-width: see nand.txt
> +- nand-ecc-mode: see nand.txt
> +
> +Required properties for hardware ECC:
> +- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand.txt)
> +- nand-ecc-step-size: step size equals page size, currently only 2k pages are
> +    supported
> +- nand-on-flash-bbt: see nand.txt
> +
> +Example:
> +
> +	nfc: nand@400e0000 {
> +		compatible = "fsl,vf610-nfc";
> +		#address-cells = <1>;
> +		#size-cells = <1>;

Fixed this to <0> ^^^

and pushed to l2-mtd.git. I'll assume the DTS updates can be rebased and
taken through arm-soc

> +		reg = <0x400e0000 0x4000>;
> +		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&clks VF610_CLK_NFC>;
> +		clock-names = "nfc";
> +		assigned-clocks = <&clks VF610_CLK_NFC>;
> +		assigned-clock-rates = <33000000>;
> +
> +		nand@0 {
> +			compatible = "fsl,vf610-nfc-nandcs";
> +			reg = <0>;
> +			nand-bus-width = <8>;
> +			nand-ecc-mode = "hw";
> +			nand-ecc-strength = <32>;
> +			nand-ecc-step-size = <2048>;
> +			nand-on-flash-bbt;
> +		};
> +	};
> -- 
> 2.5.1
> 

Brian
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[toc] | [standalone]

Back to top | Article view | linux.kernel

csiph-web