Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]
Groups > linux.kernel > #1221442 > unrolled thread
| Started by | Cyrille Pitchen <cyrille.pitchen@atmel.com> |
|---|---|
| First post | 2015-09-09 15:30 +0200 |
| Last post | 2015-09-10 12:40 +0200 |
| Articles | 5 — 2 participants |
Back to article view | Back to linux.kernel
[PATCH linux-next v6 0/8] add driver for Atmel QSPI controller Cyrille Pitchen <cyrille.pitchen@atmel.com> - 2015-09-09 15:30 +0200
[PATCH linux-next v6 2/8] mtd: spi-nor: remove unused read_xfer/write_xfer hooks Cyrille Pitchen <cyrille.pitchen@atmel.com> - 2015-09-09 15:30 +0200
[PATCH linux-next v6 6/8] mtd: spi-nor: allow to tune the number of dummy cycles Cyrille Pitchen <cyrille.pitchen@atmel.com> - 2015-09-09 15:40 +0200
[PATCH linux-next v6 8/8] mtd: atmel-quadspi: add driver for Atmel QSPI controller Cyrille Pitchen <cyrille.pitchen@atmel.com> - 2015-09-09 15:40 +0200
Re: [PATCH linux-next v6 0/8] add driver for Atmel QSPI controller Jonas Gorski <jogo@openwrt.org> - 2015-09-10 12:40 +0200
| From | Cyrille Pitchen <cyrille.pitchen@atmel.com> |
|---|---|
| Date | 2015-09-09 15:30 +0200 |
| Subject | [PATCH linux-next v6 0/8] add driver for Atmel QSPI controller |
| Message-ID | <q6NBN-4jS-15@gated-at.bofh.it> |
ChangeLog
v6:
- add new patch which tries to read the JEDEC ID with different SPI protocols
and different commands: 0x9f (SPI-1-1-1), 0xaf (SPI-4-4-4) and finally
0xaf (SPI-2-2-2).
- remove the set_protocol() hook from struct spi_nor and add 4 new members
instead of type enum spi_protocol:
read_proto, write_proto, erase_proto, reg_proto.
The relevant protocol value should be checked by the driver specific read(),
write(), erase(), read_reg() and write_reg() hook implementations.
- remove unused hooks: write_xfer() and read_xfer().
- tune the op code for read, write and erase commands depending on the memory
manufacturer.
- remove some previously added "Acked-by" since the protocol switch strategy
has been changed but not discussed yet.
v5:
- remove unused inline functions qspi_read[bw]() and qspi_write[bw](),
keep only qspi_readl() and qspi_writel().
- use reinit_completion() instead of init_completion() during run time,
call init_completion() once for all in the probe().
- add a dev_warn() when trying to tune the number of dummy cycles for
spi-nor of a not supported manufacturer then fall back to the default
framework value.
- reword some comments.
- add "Acked-by: Marek Vasut <marex@denx.de>" for patches 1 and 4.
- add "Acked-by: Bean Huo <beanhuo@micron.com>" for patch 1.
v4:
- add "OF && HAS_DMA" dependency in Kconfig for Atmel Quad SPI driver.
- return -ENOMEM instead of the return code of dma_mapping_error() as this
function returns a boolean on ARM achitecture.
- add "Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>" for Atmel Quad
SPI driver and its DT binding documentation.
v3:
- reword the comment which explains that spi_nor_set_protocol() is used by
the spi-nor framework to notify lower layers, especially the (Q)SPI
controller about a protocol change.
- change the definitions of register/bitfield macros in the Atmel QSPI
controller driver: get rid of concatenation operator and use BIT and
GENMASK macros when possible.
- use #define[SPACE] instead of #define[TAB]
v2:
- remove the patches to set the "latency code" of Spansion QSPI memories
(support of Spansion memories may be submitted in later series).
- rename "qspi" node into "spi" in the DT example to fit ePAPR standard.
- remove the useless "qspi0" label from the DT node example.
- remove the leading 0 from the size of the second memory region to make
it consistent with the size of the first memory region.
- indent the DT bindings documentation to make it more readable.
- remove the useless ".bus = &platform_bus_type," line from the
platform driver definition.
v1:
This series of patches add support for the new Atmel QSPI controller
embedded inside sama5d2x SoCs.
These patches were first developped for linux-3.18-at91 and tested on a
sama5d27 Xplained ultra board, which embeds a Micron n25q128a13 QSPI NOR
flash memory. Then the series was adapted for mainline.
Cyrille Pitchen (8):
mtd: spi-nor: read JEDEC ID with multiple I/O protocols
mtd: spi-nor: remove unused read_xfer/write_xfer hooks
mtd: spi-nor: update the SPI protocol when enabling manufacturer Quad
mode
mtd: spi-nor: use optimized commands for read/write/erase operations
Documentation: mtd: add a DT property to set the number of dummy
cycles
mtd: spi-nor: allow to tune the number of dummy cycles
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: atmel-quadspi: add driver for Atmel QSPI controller
.../devicetree/bindings/mtd/atmel-quadspi.txt | 29 +
.../devicetree/bindings/mtd/jedec,spi-nor.txt | 6 +
drivers/mtd/spi-nor/Kconfig | 7 +
drivers/mtd/spi-nor/Makefile | 1 +
drivers/mtd/spi-nor/atmel-quadspi.c | 889 +++++++++++++++++++++
drivers/mtd/spi-nor/spi-nor.c | 356 +++++++--
include/linux/mtd/spi-nor.h | 63 +-
7 files changed, 1269 insertions(+), 82 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mtd/atmel-quadspi.txt
create mode 100644 drivers/mtd/spi-nor/atmel-quadspi.c
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[toc] | [next] | [standalone]
| From | Cyrille Pitchen <cyrille.pitchen@atmel.com> |
|---|---|
| Date | 2015-09-09 15:30 +0200 |
| Subject | [PATCH linux-next v6 2/8] mtd: spi-nor: remove unused read_xfer/write_xfer hooks |
| Message-ID | <q6NBP-4jS-67@gated-at.bofh.it> |
| In reply to | #1221442 |
struct spi_nor_xfer_cfg and read_xfer/write_xfer hooks were never used by
any driver. Do some cleanup by removing them.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
include/linux/mtd/spi-nor.h | 35 -----------------------------------
1 file changed, 35 deletions(-)
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 66a5f144728a..08e405cbb6af 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -98,33 +98,6 @@ enum spi_protocol {
SPI_PROTO_4_4_4, /* Quad Command */
};
-/**
- * struct spi_nor_xfer_cfg - Structure for defining a Serial Flash transfer
- * @wren: command for "Write Enable", or 0x00 for not required
- * @cmd: command for operation
- * @cmd_pins: number of pins to send @cmd (1, 2, 4)
- * @addr: address for operation
- * @addr_pins: number of pins to send @addr (1, 2, 4)
- * @addr_width: number of address bytes
- * (3,4, or 0 for address not required)
- * @mode: mode data
- * @mode_pins: number of pins to send @mode (1, 2, 4)
- * @mode_cycles: number of mode cycles (0 for mode not required)
- * @dummy_cycles: number of dummy cycles (0 for dummy not required)
- */
-struct spi_nor_xfer_cfg {
- u8 wren;
- u8 cmd;
- u8 cmd_pins;
- u32 addr;
- u8 addr_pins;
- u8 addr_width;
- u8 mode;
- u8 mode_pins;
- u8 mode_cycles;
- u8 dummy_cycles;
-};
-
#define SPI_NOR_MAX_CMD_SIZE 8
enum spi_nor_ops {
SPI_NOR_OPS_READ = 0,
@@ -152,7 +125,6 @@ enum spi_nor_option_flags {
* @flash_read: the mode of the read
* @sst_write_second: used by the SST write operation
* @flags: flag options for the current SPI-NOR (SNOR_F_*)
- * @cfg: used by the read_xfer/write_xfer
* @erase_proto: the SPI protocol used by erase operations
* @read_proto: the SPI protocol used by read operations
* @write_proto: the SPI protocol used by write operations
@@ -162,8 +134,6 @@ enum spi_nor_option_flags {
* read/write/erase/lock/unlock operations
* @unprepare: [OPTIONAL] do some post work after the
* read/write/erase/lock/unlock operations
- * @read_xfer: [OPTIONAL] the read fundamental primitive
- * @write_xfer: [OPTIONAL] the writefundamental primitive
* @read_reg: [DRIVER-SPECIFIC] read out the register
* @write_reg: [DRIVER-SPECIFIC] write data to the register
* @read: [DRIVER-SPECIFIC] read data from the SPI NOR
@@ -191,15 +161,10 @@ struct spi_nor {
enum read_mode flash_read;
bool sst_write_second;
u32 flags;
- struct spi_nor_xfer_cfg cfg;
u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE];
int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops);
void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops);
- int (*read_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg,
- u8 *buf, size_t len);
- int (*write_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg,
- u8 *buf, size_t len);
int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len,
int write_enable);
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[toc] | [prev] | [next] | [standalone]
| From | Cyrille Pitchen <cyrille.pitchen@atmel.com> |
|---|---|
| Date | 2015-09-09 15:40 +0200 |
| Subject | [PATCH linux-next v6 6/8] mtd: spi-nor: allow to tune the number of dummy cycles |
| Message-ID | <q6NLt-4vi-29@gated-at.bofh.it> |
| In reply to | #1221442 |
The number of dummy cycles used during Fast Read commands can be reduced
to improve transfer performances. Each manufacturer has a dedicated set of
registers to provide the memory with the exact number of dummy cycles it
should expect. Both the memory and the (Q)SPI controller must agree on
this number of dummy cycles.
The number of dummy cycles can be found into the memory datasheet and
mostly depends on the SPI clock frequency, the Fast Read op code and the
Single/Dual Data Rate mode.
Probing JEDEC Serial Flash Discoverable Parameters (SFDP) tables would
only provide the driver with a high enough number of dummy cycles for each
Fast Read command to be used for all clock frequencies: this solution
would not be optimized.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/mtd/spi-nor/spi-nor.c | 102 ++++++++++++++++++++++++++++++++++--------
include/linux/mtd/spi-nor.h | 2 +
2 files changed, 85 insertions(+), 19 deletions(-)
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 820a2177ed5e..7405a1450dd1 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -121,24 +121,6 @@ static int read_cr(struct spi_nor *nor)
}
/*
- * Dummy Cycle calculation for different type of read.
- * It can be used to support more commands with
- * different dummy cycle requirements.
- */
-static inline int spi_nor_read_dummy_cycles(struct spi_nor *nor)
-{
- switch (nor->flash_read) {
- case SPI_NOR_FAST:
- case SPI_NOR_DUAL:
- case SPI_NOR_QUAD:
- return 8;
- case SPI_NOR_NORMAL:
- return 0;
- }
- return 0;
-}
-
-/*
* Write status register 1 byte
* Returns negative if error occurred.
*/
@@ -1194,6 +1176,86 @@ static void tune_manufacturer_commands(struct spi_nor *nor,
}
}
+static int micron_set_dummy_cycles(struct spi_nor *nor)
+{
+ int ret;
+ u8 val, mask;
+
+ /* Read the Volatile Configuration Register (VCR). */
+ ret = nor->read_reg(nor, SPINOR_OP_RD_VCR, &val, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error %d reading VCR\n", ret);
+ return ret;
+ }
+
+ write_enable(nor);
+
+ /* Update the number of dummy into the VCR. */
+ mask = GENMASK(7, 4);
+ val &= ~mask;
+ val |= (nor->read_dummy << 4) & mask;
+ ret = nor->write_reg(nor, SPINOR_OP_WR_VCR, &val, 1, 0);
+ if (ret < 0) {
+ dev_err(nor->dev, "error while writing VCR register\n");
+ return ret;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+/*
+ * Dummy Cycle calculation for different type of read.
+ * It can be used to support more commands with
+ * different dummy cycle requirements.
+ */
+static int spi_nor_read_dummy_cycles(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ struct device_node *np = nor->dev->of_node;
+ struct device *dev = nor->dev;
+ u32 num_dummy_cycles;
+
+ if (np && !of_property_read_u32(np, "m25p,num-dummy-cycles",
+ &num_dummy_cycles)) {
+ nor->read_dummy = num_dummy_cycles;
+
+ /*
+ * This switch block might be moved at the end of the function,
+ * once nor->read_dummy has been set, but it was not tested with
+ * all Micron memories.
+ * Now the "m25p,num-dummy-cycles" property needs to be
+ * explicitly set in the device tree so the switch statement is
+ * executed. This should avoid unwanted side effects and keep
+ * backward compatibility.
+ */
+ switch (JEDEC_MFR(info)) {
+ case CFI_MFR_ST:
+ return micron_set_dummy_cycles(nor);
+ default:
+ dev_warn(dev,
+ "Tuning of the number of dummy cycles is not implemented for spi-nor of this manufacturer,\n"
+ "ignoring the DT property value and falling back to the framework default settings.\n");
+ break;
+ }
+ }
+
+ /* Fallback to legacy code. */
+ switch (nor->flash_read) {
+ case SPI_NOR_FAST:
+ case SPI_NOR_DUAL:
+ case SPI_NOR_QUAD:
+ nor->read_dummy = 8;
+ case SPI_NOR_NORMAL:
+ nor->read_dummy = 0;
+ }
+
+ return 0;
+}
+
static int spi_nor_check(struct spi_nor *nor)
{
if (!nor->dev || !nor->read || !nor->write ||
@@ -1387,7 +1449,9 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
/* Tune read, page program and erase commands */
tune_manufacturer_commands(nor, info);
- nor->read_dummy = spi_nor_read_dummy_cycles(nor);
+ ret = spi_nor_read_dummy_cycles(nor, info);
+ if (ret)
+ return ret;
dev_info(dev, "%s (%lld Kbytes)\n", info->name,
(long long)mtd->size >> 10);
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index f13cd2cb3ac5..4a3f5d8655d8 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -66,6 +66,8 @@
#define SPINOR_OP_MIO_RDID 0xaf /* Multiple I/O Read JEDEC ID */
#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */
+#define SPINOR_OP_RD_VCR 0x85 /* Read VCR register */
+#define SPINOR_OP_WR_VCR 0x81 /* Write VCR register */
/* Status Register bits. */
#define SR_WIP 1 /* Write in progress */
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[toc] | [prev] | [next] | [standalone]
| From | Cyrille Pitchen <cyrille.pitchen@atmel.com> |
|---|---|
| Date | 2015-09-09 15:40 +0200 |
| Subject | [PATCH linux-next v6 8/8] mtd: atmel-quadspi: add driver for Atmel QSPI controller |
| Message-ID | <q6NLt-4vi-27@gated-at.bofh.it> |
| In reply to | #1221442 |
This driver add support to the new Atmel QSPI controller embedded into
sama5d2x SoCs. It expects a NOR memory to be connected to the QSPI
controller.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/mtd/spi-nor/Kconfig | 7 +
drivers/mtd/spi-nor/Makefile | 1 +
drivers/mtd/spi-nor/atmel-quadspi.c | 889 ++++++++++++++++++++++++++++++++++++
3 files changed, 897 insertions(+)
create mode 100644 drivers/mtd/spi-nor/atmel-quadspi.c
diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
index 89bf4c1faa2b..7a3d55429550 100644
--- a/drivers/mtd/spi-nor/Kconfig
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -29,6 +29,13 @@ config SPI_FSL_QUADSPI
This controller does not support generic SPI. It only supports
SPI NOR.
+config SPI_ATMEL_QUADSPI
+ tristate "Atmel Quad SPI Controller"
+ depends on OF && HAS_DMA && (ARCH_AT91 || COMPILE_TEST)
+ help
+ This enables support for the Quad SPI controller in master mode.
+ We only connect the NOR to this controller now.
+
config SPI_NXP_SPIFI
tristate "NXP SPI Flash Interface (SPIFI)"
depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
index e53333ef8582..f5d23d7379bb 100644
--- a/drivers/mtd/spi-nor/Makefile
+++ b/drivers/mtd/spi-nor/Makefile
@@ -1,3 +1,4 @@
obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o
obj-$(CONFIG_SPI_FSL_QUADSPI) += fsl-quadspi.o
+obj-$(CONFIG_SPI_ATMEL_QUADSPI) += atmel-quadspi.o
obj-$(CONFIG_SPI_NXP_SPIFI) += nxp-spifi.o
diff --git a/drivers/mtd/spi-nor/atmel-quadspi.c b/drivers/mtd/spi-nor/atmel-quadspi.c
new file mode 100644
index 000000000000..dc0c1d8293d5
--- /dev/null
+++ b/drivers/mtd/spi-nor/atmel-quadspi.c
@@ -0,0 +1,889 @@
+/*
+ * Driver for Atmel QSPI Controller
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *
+ * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ * This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale.
+ */
+
+#include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/spi-nor.h>
+#include <linux/platform_data/atmel.h>
+#include <linux/platform_data/dma-atmel.h>
+#include <linux/of.h>
+
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/pinctrl/consumer.h>
+
+/* QSPI register offsets */
+#define QSPI_CR 0x0000 /* Control Register */
+#define QSPI_MR 0x0004 /* Mode Register */
+#define QSPI_RD 0x0008 /* Receive Data Register */
+#define QSPI_TD 0x000c /* Transmit Data Register */
+#define QSPI_SR 0x0010 /* Status Register */
+#define QSPI_IER 0x0014 /* Interrupt Enable Register */
+#define QSPI_IDR 0x0018 /* Interrupt Disable Register */
+#define QSPI_IMR 0x001c /* Interrupt Mask Register */
+#define QSPI_SCR 0x0020 /* Serial Clock Register */
+
+#define QSPI_IAR 0x0030 /* Instruction Address Register */
+#define QSPI_ICR 0x0034 /* Instruction Code Register */
+#define QSPI_IFR 0x0038 /* Instruction Frame Register */
+
+#define QSPI_SMR 0x0040 /* Scrambling Mode Register */
+#define QSPI_SKR 0x0044 /* Scrambling Key Register */
+
+#define QSPI_WPMR 0x00E4 /* Write Protection Mode Register */
+#define QSPI_WPSR 0x00E8 /* Write Protection Status Register */
+
+#define QSPI_VERSION 0x00FC /* Version Register */
+
+
+/* Bitfields in QSPI_CR (Control Register) */
+#define QSPI_CR_QSPIEN BIT(0)
+#define QSPI_CR_QSPIDIS BIT(1)
+#define QSPI_CR_SWRST BIT(7)
+#define QSPI_CR_LASTXFER BIT(24)
+
+/* Bitfields in QSPI_MR (Mode Register) */
+#define QSPI_MR_SSM BIT(0)
+#define QSPI_MR_LLB BIT(1)
+#define QSPI_MR_WDRBT BIT(2)
+#define QSPI_MR_SMRM BIT(3)
+#define QSPI_MR_CSMODE_MASK GENMASK(5, 4)
+#define QSPI_MR_CSMODE_NOT_RELOADED (0 << 4)
+#define QSPI_MR_CSMODE_LASTXFER (1 << 4)
+#define QSPI_MR_CSMODE_SYSTEMATICALLY (2 << 4)
+#define QSPI_MR_NBBITS_MASK GENMASK(11, 8)
+#define QSPI_MR_NBBITS(n) ((((n) - 8) << 8) & QSPI_MR_NBBITS_MASK)
+#define QSPI_MR_DLYBCT_MASK GENMASK(23, 16)
+#define QSPI_MR_DLYBCT(n) (((n) << 16) & QSPI_MR_DLYBCT_MASK)
+#define QSPI_MR_DLYCS_MASK GENMASK(31, 24)
+#define QSPI_MR_DLYCS(n) (((n) << 24) & QSPI_MR_DLYCS_MASK)
+
+/* Bitfields in QSPI_SR/QSPI_IER/QSPI_IDR/QSPI_IMR */
+#define QSPI_SR_RDRF BIT(0)
+#define QSPI_SR_TDRE BIT(1)
+#define QSPI_SR_TXEMPTY BIT(2)
+#define QSPI_SR_OVRES BIT(3)
+#define QSPI_SR_CSR BIT(8)
+#define QSPI_SR_CSS BIT(9)
+#define QSPI_SR_INSTRE BIT(10)
+#define QSPI_SR_QSPIENS BIT(24)
+
+/* Bitfields in QSPI_SCR (Serial Clock Register) */
+#define QSPI_SCR_CPOL BIT(0)
+#define QSPI_SCR_CPHA BIT(1)
+#define QSPI_SCR_SCBR_MASK GENMASK(15, 8)
+#define QSPI_SCR_SCBR(n) (((n) << 8) & QSPI_SCR_SCBR_MASK)
+#define QSPI_SCR_DLYBS_MASK GENMASK(23, 16)
+#define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK)
+
+/* Bitfields in QSPI_ICR (Instruction Code Register) */
+#define QSPI_ICR_INST_MASK GENMASK(7, 0)
+#define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK)
+#define QSPI_ICR_OPT_MASK GENMASK(23, 16)
+#define QSPI_ICR_OPT(opt) (((opt) << 16) & QSPI_ICR_OPT_MASK)
+
+/* Bitfields in QSPI_IFR (Instruction Frame Register) */
+#define QSPI_IFR_WIDTH_MASK GENMASK(2, 0)
+#define QSPI_IFR_WIDTH_SINGLE_BIT_SPI (0 << 0)
+#define QSPI_IFR_WIDTH_DUAL_OUTPUT (1 << 0)
+#define QSPI_IFR_WIDTH_QUAD_OUTPUT (2 << 0)
+#define QSPI_IFR_WIDTH_DUAL_IO (3 << 0)
+#define QSPI_IFR_WIDTH_QUAD_IO (4 << 0)
+#define QSPI_IFR_WIDTH_DUAL_CMD (5 << 0)
+#define QSPI_IFR_WIDTH_QUAD_CMD (6 << 0)
+#define QSPI_IFR_INSTEN BIT(4)
+#define QSPI_IFR_ADDREN BIT(5)
+#define QSPI_IFR_OPTEN BIT(6)
+#define QSPI_IFR_DATAEN BIT(7)
+#define QSPI_IFR_OPTL_MASK GENMASK(9, 8)
+#define QSPI_IFR_OPTL_1BIT (0 << 8)
+#define QSPI_IFR_OPTL_2BIT (1 << 8)
+#define QSPI_IFR_OPTL_4BIT (2 << 8)
+#define QSPI_IFR_OPTL_8BIT (3 << 8)
+#define QSPI_IFR_ADDRL BIT(10)
+#define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12)
+#define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12)
+#define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12)
+#define QSPI_IFR_TFRTYP_TRSFR_WRITE (2 << 12)
+#define QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM (3 << 13)
+#define QSPI_IFR_CRM BIT(14)
+#define QSPI_IFR_NBDUM_MASK GENMASK(20, 16)
+#define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK)
+
+/* Bitfields in QSPI_SMR (Scrambling Mode Register) */
+#define QSPI_SMR_SCREN BIT(0)
+#define QSPI_SMR_RVDIS BIT(1)
+
+/* Bitfields in QSPI_WPMR (Write Protection Mode Register) */
+#define QSPI_WPMR_WPEN BIT(0)
+#define QSPI_WPMR_WPKEY_MASK GENMASK(31, 8)
+#define QSPI_WPMR_WPKEY(wpkey) (((wpkey) << 8) & QSPI_WPMR_WPKEY_MASK)
+
+/* Bitfields in QSPI_WPSR (Write Protection Status Register) */
+#define QSPI_WPSR_WPVS BIT(0)
+#define QSPI_WPSR_WPVSRC_MASK GENMASK(15, 8)
+#define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC)
+
+
+struct atmel_qspi {
+ void __iomem *regs;
+ void __iomem *mem;
+ dma_addr_t phys_addr;
+ struct dma_chan *chan;
+ struct clk *clk;
+ struct platform_device *pdev;
+ u32 pending;
+
+ struct mtd_info mtd;
+ struct spi_nor nor;
+ u32 clk_rate;
+ struct completion cmd_completion;
+ struct completion dma_completion;
+
+#ifdef DEBUG
+ u8 last_instruction;
+#endif
+};
+
+struct atmel_qspi_command {
+ u32 ifr;
+ union {
+ struct {
+ u32 instruction:1;
+ u32 address:3;
+ u32 mode:1;
+ u32 dummy:1;
+ u32 data:1;
+ u32 dma:1;
+ u32 reserved:24;
+ } bits;
+ u32 word;
+ } enable;
+ u8 instruction;
+ u8 mode;
+ u8 num_mode_cycles;
+ u8 num_dummy_cycles;
+ u32 address;
+
+ size_t buf_len;
+ const void *tx_buf;
+ void *rx_buf;
+};
+
+/* Register access functions */
+static inline u32 qspi_readl(struct atmel_qspi *aq, u32 reg)
+{
+ return readl_relaxed(aq->regs + reg);
+}
+
+static inline void qspi_writel(struct atmel_qspi *aq, u32 reg, u32 value)
+{
+ writel_relaxed(value, aq->regs + reg);
+}
+
+
+#define QSPI_DMA_THRESHOLD 32
+
+static void atmel_qspi_dma_callback(void *arg)
+{
+ struct completion *dma_completion = arg;
+
+ complete(dma_completion);
+}
+
+static int atmel_qspi_run_dma_transfer(struct atmel_qspi *aq,
+ const struct atmel_qspi_command *cmd)
+{
+ u32 offset = (cmd->enable.bits.address) ? cmd->address : 0;
+ struct dma_chan *chan = aq->chan;
+ struct device *dev = &aq->pdev->dev;
+ enum dma_data_direction direction;
+ dma_addr_t phys_addr, dst, src;
+ struct dma_async_tx_descriptor *desc;
+ dma_cookie_t cookie;
+ int err = 0;
+
+ if (cmd->tx_buf) {
+ direction = DMA_TO_DEVICE;
+ phys_addr = dma_map_single(dev, (void *)cmd->tx_buf,
+ cmd->buf_len, direction);
+ src = phys_addr;
+ dst = aq->phys_addr + offset;
+ } else {
+ direction = DMA_FROM_DEVICE;
+ phys_addr = dma_map_single(dev, (void *)cmd->rx_buf,
+ cmd->buf_len, direction);
+ src = aq->phys_addr + offset;
+ dst = phys_addr;
+ }
+ if (dma_mapping_error(dev, phys_addr))
+ return -ENOMEM;
+
+ desc = chan->device->device_prep_dma_memcpy(chan, dst, src,
+ cmd->buf_len,
+ DMA_PREP_INTERRUPT);
+ if (!desc) {
+ err = -ENOMEM;
+ goto unmap_single;
+ }
+
+ reinit_completion(&aq->dma_completion);
+ desc->callback = atmel_qspi_dma_callback;
+ desc->callback_param = &aq->dma_completion;
+ cookie = dmaengine_submit(desc);
+ err = dma_submit_error(cookie);
+ if (err)
+ goto unmap_single;
+ dma_async_issue_pending(chan);
+
+ if (!wait_for_completion_timeout(&aq->dma_completion,
+ msecs_to_jiffies(1000)))
+ err = -ETIMEDOUT;
+
+ if (dma_async_is_tx_complete(chan, cookie, NULL, NULL) != DMA_COMPLETE)
+ err = -ETIMEDOUT;
+
+ if (err)
+ dmaengine_terminate_all(chan);
+unmap_single:
+ dma_unmap_single(dev, phys_addr, cmd->buf_len, direction);
+
+ return err;
+}
+
+static int atmel_qspi_run_transfer(struct atmel_qspi *aq,
+ const struct atmel_qspi_command *cmd)
+{
+ void __iomem *ahb_mem;
+
+ /* First try a DMA transfer */
+ if (aq->chan && cmd->enable.bits.dma &&
+ cmd->buf_len >= QSPI_DMA_THRESHOLD)
+ return atmel_qspi_run_dma_transfer(aq, cmd);
+
+ /* Then fallback to a PIO transfer */
+ ahb_mem = aq->mem;
+ if (cmd->enable.bits.address)
+ ahb_mem += cmd->address;
+ if (cmd->tx_buf)
+ memcpy_toio(ahb_mem, cmd->tx_buf, cmd->buf_len);
+ else
+ memcpy_fromio(cmd->rx_buf, ahb_mem, cmd->buf_len);
+
+ return 0;
+}
+
+#ifdef DEBUG
+static void atmel_qspi_debug_command(struct atmel_qspi *aq,
+ const struct atmel_qspi_command *cmd)
+{
+ u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE];
+ size_t len = 0;
+ int i;
+
+ if (cmd->enable.bits.instruction) {
+ if (aq->last_instruction == cmd->instruction)
+ return;
+ aq->last_instruction = cmd->instruction;
+ }
+
+ if (cmd->enable.bits.instruction)
+ cmd_buf[len++] = cmd->instruction;
+
+ for (i = cmd->enable.bits.address-1; i >= 0; --i)
+ cmd_buf[len++] = (cmd->address >> (i << 3)) & 0xff;
+
+ if (cmd->enable.bits.mode)
+ cmd_buf[len++] = cmd->mode;
+
+ if (cmd->enable.bits.dummy) {
+ int num = cmd->num_dummy_cycles;
+
+ switch (cmd->ifr & QSPI_IFR_WIDTH_MASK) {
+ case QSPI_IFR_WIDTH_SINGLE_BIT_SPI:
+ case QSPI_IFR_WIDTH_DUAL_OUTPUT:
+ case QSPI_IFR_WIDTH_QUAD_OUTPUT:
+ num >>= 3;
+ break;
+ case QSPI_IFR_WIDTH_DUAL_IO:
+ case QSPI_IFR_WIDTH_DUAL_CMD:
+ num >>= 2;
+ break;
+ case QSPI_IFR_WIDTH_QUAD_IO:
+ case QSPI_IFR_WIDTH_QUAD_CMD:
+ num >>= 1;
+ break;
+ default:
+ return;
+ }
+
+ for (i = 0; i < num; ++i)
+ cmd_buf[len++] = 0;
+ }
+
+ /* Dump the SPI command */
+ print_hex_dump(KERN_DEBUG, "qspi cmd: ", DUMP_PREFIX_NONE,
+ 32, 1, cmd_buf, len, false);
+
+#ifdef VERBOSE_DEBUG
+ /* If verbose debug is enabled, also dump the TX data */
+ if (cmd->enable.bits.data && cmd->tx_buf)
+ print_hex_dump(KERN_DEBUG, "qspi tx : ", DUMP_PREFIX_NONE,
+ 32, 1, cmd->tx_buf, cmd->buf_len, false);
+#endif
+}
+#else
+#define atmel_qspi_debug_command(aq, cmd)
+#endif
+
+static int atmel_qspi_run_command(struct atmel_qspi *aq,
+ const struct atmel_qspi_command *cmd)
+{
+ u32 iar, icr, ifr, sr;
+ int err = 0;
+
+ iar = 0;
+ icr = 0;
+ ifr = cmd->ifr;
+
+ /* Compute instruction parameters */
+ if (cmd->enable.bits.instruction) {
+ icr |= QSPI_ICR_INST(cmd->instruction);
+ ifr |= QSPI_IFR_INSTEN;
+ }
+
+ /* Compute address parameters */
+ switch (cmd->enable.bits.address) {
+ case 4:
+ ifr |= QSPI_IFR_ADDRL;
+ /* fall through to the 24bit (3 byte) address case. */
+ case 3:
+ iar = (cmd->enable.bits.data) ? 0 : cmd->address;
+ ifr |= QSPI_IFR_ADDREN;
+ break;
+ case 0:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* Compute option parameters */
+ if (cmd->enable.bits.mode && cmd->num_mode_cycles) {
+ u32 mode_cycle_bits, mode_bits;
+
+ icr |= QSPI_ICR_OPT(cmd->mode);
+ ifr |= QSPI_IFR_OPTEN;
+
+ switch (ifr & QSPI_IFR_WIDTH_MASK) {
+ case QSPI_IFR_WIDTH_SINGLE_BIT_SPI:
+ case QSPI_IFR_WIDTH_DUAL_OUTPUT:
+ case QSPI_IFR_WIDTH_QUAD_OUTPUT:
+ mode_cycle_bits = 1;
+ break;
+ case QSPI_IFR_WIDTH_DUAL_IO:
+ case QSPI_IFR_WIDTH_DUAL_CMD:
+ mode_cycle_bits = 2;
+ break;
+ case QSPI_IFR_WIDTH_QUAD_IO:
+ case QSPI_IFR_WIDTH_QUAD_CMD:
+ mode_cycle_bits = 4;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ mode_bits = cmd->num_mode_cycles * mode_cycle_bits;
+ switch (mode_bits) {
+ case 1:
+ ifr |= QSPI_IFR_OPTL_1BIT;
+ break;
+
+ case 2:
+ ifr |= QSPI_IFR_OPTL_2BIT;
+ break;
+
+ case 4:
+ ifr |= QSPI_IFR_OPTL_4BIT;
+ break;
+
+ case 8:
+ ifr |= QSPI_IFR_OPTL_8BIT;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ }
+
+ /* Set number of dummy cycles */
+ if (cmd->enable.bits.dummy)
+ ifr |= QSPI_IFR_NBDUM(cmd->num_dummy_cycles);
+
+ /* Set data enable */
+ if (cmd->enable.bits.data) {
+ ifr |= QSPI_IFR_DATAEN;
+
+ /* Special case for Continuous Read Mode */
+ if (!cmd->tx_buf && !cmd->rx_buf)
+ ifr |= QSPI_IFR_CRM;
+ }
+
+ /* Set QSPI Instruction Frame registers */
+ atmel_qspi_debug_command(aq, cmd);
+ qspi_writel(aq, QSPI_IAR, iar);
+ qspi_writel(aq, QSPI_ICR, icr);
+ qspi_writel(aq, QSPI_IFR, ifr);
+
+ /* Skip to the final steps if there is no data */
+ if (!cmd->enable.bits.data)
+ goto no_data;
+
+ /* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
+ (void)qspi_readl(aq, QSPI_IFR);
+
+ /* Stop here for continuous read */
+ if (!cmd->tx_buf && !cmd->rx_buf)
+ return 0;
+ /* Send/Receive data */
+ err = atmel_qspi_run_transfer(aq, cmd);
+
+ /* Release the chip-select */
+ qspi_writel(aq, QSPI_CR, QSPI_CR_LASTXFER);
+
+ if (err)
+ return err;
+
+#if defined(DEBUG) && defined(VERBOSE_DEBUG)
+ /*
+ * If verbose debug is enabled, also dump the RX data in addition to
+ * the SPI command previously dumped by atmel_qspi_debug_command()
+ */
+ if (cmd->rx_buf)
+ print_hex_dump(KERN_DEBUG, "qspi rx : ", DUMP_PREFIX_NONE,
+ 32, 1, cmd->rx_buf, cmd->buf_len, false);
+#endif
+no_data:
+ /* Poll INSTRuction End status */
+ sr = qspi_readl(aq, QSPI_SR);
+ if (sr & QSPI_SR_INSTRE)
+ return err;
+
+ /* Wait for INSTRuction End interrupt */
+ reinit_completion(&aq->cmd_completion);
+ aq->pending = 0;
+ qspi_writel(aq, QSPI_IER, QSPI_SR_INSTRE);
+ if (!wait_for_completion_timeout(&aq->cmd_completion,
+ msecs_to_jiffies(1000)))
+ err = -ETIMEDOUT;
+ qspi_writel(aq, QSPI_IDR, QSPI_SR_INSTRE);
+
+ return err;
+}
+
+static int atmel_qspi_command_set_ifr(struct atmel_qspi_command *cmd,
+ u32 ifr_tfrtyp,
+ enum spi_protocol proto)
+{
+ cmd->ifr = ifr_tfrtyp;
+
+ switch (proto) {
+ case SPI_PROTO_1_1_1:
+ cmd->ifr |= QSPI_IFR_WIDTH_SINGLE_BIT_SPI;
+ break;
+ case SPI_PROTO_1_1_2:
+ cmd->ifr |= QSPI_IFR_WIDTH_DUAL_OUTPUT;
+ break;
+ case SPI_PROTO_1_1_4:
+ cmd->ifr |= QSPI_IFR_WIDTH_QUAD_OUTPUT;
+ break;
+ case SPI_PROTO_1_2_2:
+ cmd->ifr |= QSPI_IFR_WIDTH_DUAL_IO;
+ break;
+ case SPI_PROTO_1_4_4:
+ cmd->ifr |= QSPI_IFR_WIDTH_QUAD_IO;
+ break;
+ case SPI_PROTO_2_2_2:
+ cmd->ifr |= QSPI_IFR_WIDTH_DUAL_CMD;
+ break;
+ case SPI_PROTO_4_4_4:
+ cmd->ifr |= QSPI_IFR_WIDTH_QUAD_CMD;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int atmel_qspi_read_reg(struct spi_nor *nor, u8 opcode,
+ u8 *buf, int len)
+{
+ struct atmel_qspi *aq = nor->priv;
+ struct atmel_qspi_command cmd;
+ int ret;
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.enable.bits.instruction = 1;
+ cmd.enable.bits.data = 1;
+ cmd.instruction = opcode;
+ cmd.rx_buf = buf;
+ cmd.buf_len = len;
+
+ ret = atmel_qspi_command_set_ifr(&cmd,
+ QSPI_IFR_TFRTYP_TRSFR_READ,
+ nor->reg_proto);
+ if (ret)
+ return ret;
+
+ return atmel_qspi_run_command(aq, &cmd);
+}
+
+static int atmel_qspi_write_reg(struct spi_nor *nor, u8 opcode,
+ u8 *buf, int len,
+ int write_enable)
+{
+ struct atmel_qspi *aq = nor->priv;
+ struct atmel_qspi_command cmd;
+ int ret;
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.enable.bits.instruction = 1;
+ cmd.enable.bits.data = (buf != NULL && len > 0);
+ cmd.instruction = opcode;
+ cmd.tx_buf = buf;
+ cmd.buf_len = len;
+
+ ret = atmel_qspi_command_set_ifr(&cmd,
+ QSPI_IFR_TFRTYP_TRSFR_WRITE,
+ nor->reg_proto);
+ if (ret)
+ return ret;
+
+ return atmel_qspi_run_command(aq, &cmd);
+}
+
+static void atmel_qspi_write(struct spi_nor *nor, loff_t to, size_t len,
+ size_t *retlen, const u_char *write_buf)
+{
+ struct atmel_qspi *aq = nor->priv;
+ struct atmel_qspi_command cmd;
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.enable.bits.instruction = 1;
+ cmd.enable.bits.address = nor->addr_width;
+ cmd.enable.bits.data = 1;
+ cmd.enable.bits.dma = 1;
+ cmd.instruction = nor->program_opcode;
+ cmd.address = (u32)to;
+ cmd.tx_buf = write_buf;
+ cmd.buf_len = len;
+
+ if (atmel_qspi_command_set_ifr(&cmd,
+ QSPI_IFR_TFRTYP_TRSFR_WRITE_MEM,
+ nor->write_proto))
+ return;
+
+ if (!atmel_qspi_run_command(aq, &cmd))
+ *retlen += len;
+}
+
+static int atmel_qspi_erase(struct spi_nor *nor, loff_t offs)
+{
+ struct atmel_qspi *aq = nor->priv;
+ struct atmel_qspi_command cmd;
+ int ret;
+
+ dev_dbg(nor->dev, "%dKiB at 0x%08x\n",
+ aq->mtd.erasesize / 1024, (u32)offs);
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.enable.bits.instruction = 1;
+ cmd.enable.bits.address = nor->addr_width;
+ cmd.instruction = nor->erase_opcode;
+ cmd.address = (u32)offs;
+
+ ret = atmel_qspi_command_set_ifr(&cmd,
+ QSPI_IFR_TFRTYP_TRSFR_WRITE,
+ nor->erase_proto);
+ if (ret)
+ return ret;
+
+ return atmel_qspi_run_command(aq, &cmd);
+}
+
+static int atmel_qspi_read(struct spi_nor *nor, loff_t from, size_t len,
+ size_t *retlen, u_char *read_buf)
+{
+ struct atmel_qspi *aq = nor->priv;
+ struct atmel_qspi_command cmd;
+ int ret;
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.enable.bits.instruction = 1;
+ cmd.enable.bits.address = nor->addr_width;
+ cmd.enable.bits.dummy = (nor->read_dummy > 0);
+ cmd.enable.bits.data = 1;
+ cmd.enable.bits.dma = 1;
+ cmd.instruction = nor->read_opcode;
+ cmd.address = (u32)from;
+ cmd.num_dummy_cycles = nor->read_dummy;
+ cmd.rx_buf = read_buf;
+ cmd.buf_len = len;
+
+ ret = atmel_qspi_command_set_ifr(&cmd,
+ QSPI_IFR_TFRTYP_TRSFR_READ_MEM,
+ nor->read_proto);
+ if (ret)
+ return ret;
+
+ ret = atmel_qspi_run_command(aq, &cmd);
+ if (ret)
+ return ret;
+
+ *retlen += len;
+ return 0;
+}
+
+static int atmel_qspi_init(struct atmel_qspi *aq)
+{
+ unsigned long src_rate;
+ u32 mr, scr, scbr;
+
+ /* Reset the QSPI controller */
+ qspi_writel(aq, QSPI_CR, QSPI_CR_SWRST);
+
+ /* Set the QSPI controller in Serial Memory Mode */
+ mr = QSPI_MR_SSM | QSPI_MR_NBBITS(8);
+ qspi_writel(aq, QSPI_MR, mr);
+
+ src_rate = clk_get_rate(aq->clk);
+ if (!src_rate)
+ return -EINVAL;
+
+ /* Compute the QSPI baudrate */
+ scbr = DIV_ROUND_UP(src_rate, aq->clk_rate);
+ if (scbr > 0)
+ scbr--;
+ scr = QSPI_SCR_SCBR(scbr);
+ qspi_writel(aq, QSPI_SCR, scr);
+
+ /* Enable the QSPI controller */
+ qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIEN);
+
+ return 0;
+}
+
+static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id)
+{
+ struct atmel_qspi *aq = (struct atmel_qspi *)dev_id;
+ u32 status, mask, pending;
+
+ status = qspi_readl(aq, QSPI_SR);
+ mask = qspi_readl(aq, QSPI_IMR);
+ pending = status & mask;
+
+ if (!pending)
+ return IRQ_NONE;
+
+ aq->pending |= pending;
+ if (pending & QSPI_SR_INSTRE)
+ complete(&aq->cmd_completion);
+
+ return IRQ_HANDLED;
+}
+
+static int atmel_qspi_probe(struct platform_device *pdev)
+{
+ struct device_node *child, *np = pdev->dev.of_node;
+ struct mtd_part_parser_data ppdata;
+ struct atmel_qspi *aq;
+ struct resource *res;
+ dma_cap_mask_t mask;
+ struct spi_nor *nor;
+ struct mtd_info *mtd;
+ char modalias[40];
+ int irq, err = 0;
+
+ if (of_get_child_count(np) != 1)
+ return -ENODEV;
+ child = of_get_next_child(np, NULL);
+
+ aq = devm_kzalloc(&pdev->dev, sizeof(*aq), GFP_KERNEL);
+ if (!aq) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ platform_set_drvdata(pdev, aq);
+ init_completion(&aq->cmd_completion);
+ init_completion(&aq->dma_completion);
+ aq->pdev = pdev;
+
+ /* Map the registers */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ aq->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(aq->regs)) {
+ dev_err(&pdev->dev, "missing registers\n");
+ err = PTR_ERR(aq->regs);
+ goto exit;
+ }
+
+ /* Map the AHB memory */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ aq->mem = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(aq->mem)) {
+ dev_err(&pdev->dev, "missing AHB memory\n");
+ err = PTR_ERR(aq->regs);
+ goto exit;
+ }
+ aq->phys_addr = (dma_addr_t)res->start;
+
+ /* Get the peripheral clock */
+ aq->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(aq->clk)) {
+ dev_err(&pdev->dev, "missing peripheral clock\n");
+ err = PTR_ERR(aq->clk);
+ goto exit;
+ }
+
+ /* Enable the peripheral clock */
+ err = clk_prepare_enable(aq->clk);
+ if (err) {
+ dev_err(&pdev->dev, "failed to enable the peripheral clock\n");
+ goto exit;
+ }
+
+ /* Request the IRQ */
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "missing IRQ\n");
+ err = irq;
+ goto disable_clk;
+ }
+ err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt,
+ 0, dev_name(&pdev->dev), aq);
+ if (err)
+ goto disable_clk;
+
+ /* Try to get a DMA channel for memcpy() operation */
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_MEMCPY, mask);
+ aq->chan = dma_request_channel(mask, NULL, NULL);
+ if (!aq->chan)
+ dev_warn(&pdev->dev, "no available DMA channel\n");
+
+ /* Setup the spi-nor */
+ nor = &aq->nor;
+ mtd = &aq->mtd;
+
+ nor->mtd = mtd;
+ nor->dev = &pdev->dev;
+ nor->priv = aq;
+ mtd->priv = nor;
+
+ nor->read_reg = atmel_qspi_read_reg;
+ nor->write_reg = atmel_qspi_write_reg;
+ nor->read = atmel_qspi_read;
+ nor->write = atmel_qspi_write;
+ nor->erase = atmel_qspi_erase;
+
+ if (of_modalias_node(child, modalias, sizeof(modalias)) < 0) {
+ err = -ENODEV;
+ goto release_channel;
+ }
+
+ err = of_property_read_u32(child, "spi-max-frequency", &aq->clk_rate);
+ if (err < 0)
+ goto release_channel;
+
+ err = atmel_qspi_init(aq);
+ if (err)
+ goto release_channel;
+
+ nor->dev->of_node = child;
+ err = spi_nor_scan(nor, modalias, SPI_NOR_QUAD);
+ nor->dev->of_node = np;
+ if (err)
+ goto release_channel;
+
+ ppdata.of_node = child;
+ err = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
+ if (err)
+ goto release_channel;
+
+ of_node_put(child);
+
+ return 0;
+
+release_channel:
+ if (aq->chan)
+ dma_release_channel(aq->chan);
+disable_clk:
+ clk_disable_unprepare(aq->clk);
+exit:
+ of_node_put(child);
+
+ return err;
+}
+
+static int atmel_qspi_remove(struct platform_device *pdev)
+{
+ struct atmel_qspi *aq = platform_get_drvdata(pdev);
+
+ mtd_device_unregister(&aq->mtd);
+ qspi_writel(aq, QSPI_CR, QSPI_CR_QSPIDIS);
+ if (aq->chan)
+ dma_release_channel(aq->chan);
+ clk_disable_unprepare(aq->clk);
+ return 0;
+}
+
+
+static const struct of_device_id atmel_qspi_dt_ids[] = {
+ { .compatible = "atmel,sama5d2-qspi" },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_qspi_dt_ids);
+
+static struct platform_driver atmel_qspi_driver = {
+ .driver = {
+ .name = "atmel_qspi",
+ .of_match_table = atmel_qspi_dt_ids,
+ },
+ .probe = atmel_qspi_probe,
+ .remove = atmel_qspi_remove,
+};
+module_platform_driver(atmel_qspi_driver);
+
+MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>");
+MODULE_DESCRIPTION("Atmel QSPI Controller driver");
+MODULE_LICENSE("GPL v2");
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
[toc] | [prev] | [next] | [standalone]
| From | Jonas Gorski <jogo@openwrt.org> |
|---|---|
| Date | 2015-09-10 12:40 +0200 |
| Message-ID | <q77qO-7fC-13@gated-at.bofh.it> |
| In reply to | #1221442 |
Hi, On Wed, Sep 9, 2015 at 3:24 PM, Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote: > This series of patches add support for the new Atmel QSPI controller > embedded inside sama5d2x SoCs. > > These patches were first developped for linux-3.18-at91 and tested on a > sama5d27 Xplained ultra board, which embeds a Micron n25q128a13 QSPI NOR > flash memory. Then the series was adapted for mainline. All in all, this looks a lot better now compared to the previous version. What I'm still missing is some definsive programming to ensure we don't break existing users, or update the current users to not break. The issues I currently see are 1) We don't check if a spi-nor controller actually supports a certain protocol, just if SPI_NOR_DUAL/_QUAD is set 2) We currently set these new protocols, but none of the current spi-nor controller drivers are aware of the protocols, which has the possiblity of silently breaking things (or not, since they will then fail to read correct data) 3) m25p80 currently uses SPI_RX_DUAL -> SPI_NOR_DUAL, but does not check SPI_TX_DUAL (which is required for any of the != 1_1_x commands). Although this is more an academical concern, as currently all spi controller drivers seem to support _RX_ and _TX_, never only one direction. Jonas -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
[toc] | [prev] | [standalone]
Back to top | Article view | linux.kernel
csiph-web