Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1197965 > unrolled thread

Re: Nokia N900 - audio TPA6130A2 problems

Back to article view | Back to linux.kernel

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  Re: Nokia N900 - audio TPA6130A2 problems Pali Rohár <pali.rohar@gmail.com> - 2015-08-01 12:20 +0200
    Re: Nokia N900 - audio TPA6130A2 problems Pali Rohár <pali.rohar@gmail.com> - 2015-08-03 20:20 +0200
      Re: Nokia N900 - audio TPA6130A2 problems Jarkko Nikula <jarkko.nikula@bitmer.com> - 2015-08-03 20:50 +0200
        Re: Nokia N900 - audio TPA6130A2 problems Pali Rohár <pali.rohar@gmail.com> - 2015-08-03 21:00 +0200
        Re: Nokia N900 - audio TPA6130A2 problems Peter Ujfalusi <peter.ujfalusi@ti.com> - 2015-08-04 09:10 +0200
    Re: Nokia N900 - audio TPA6130A2 problems Jarkko Nikula <jarkko.nikula@bitmer.com> - 2015-08-03 20:30 +0200

#1197965 — Re: Nokia N900 - audio TPA6130A2 problems

[Multipart message — attachments visible in raw view] — view raw

On Saturday 25 July 2015 15:17:13 Lars-Peter Clausen wrote:
> On 07/25/2015 12:28 PM, Pali Rohár wrote:
> > Hello,
> > 
> > sometimes after rebooting Nokia N900 initializing alsa audio fails.
> > Here output from dmesg log when it happen:
> > 
> > [    6.925140] tpa6130a2 2-0060: Write failed
> > [    6.929534] tpa6130a2 2-0060: Failed to initialize chip
> > [    6.935272] tpa6130a2: probe of 2-0060 failed with error -121
> > [    7.624237] rx51-audio n900-audio: Failed to add TPA6130A2
> > controls [    7.635101] rx51-audio n900-audio: ASoC: failed to
> > init TLV320AIC34: -19 [    7.645874] rx51-audio n900-audio: ASoC:
> > failed to instantiate card -19 [    7.665740] rx51-audio
> > n900-audio: snd_soc_register_card failed (-19) [    8.063049] ALSA
> > device list:
> > [    8.070343]   No soundcards found.
> > 
> > Any idea what to do?
> 
> Looks like the chip is not responding. Try to add a small delay after
> powerup to give the device to be fully ready, something like the
> following:
> 
> --- a/sound/soc/codecs/tpa6130a2.c
> +++ b/sound/soc/codecs/tpa6130a2.c
> @@ -152,6 +152,8 @@ static int tpa6130a2_power(u8 power)
>   		if (data->power_gpio >= 0)
>   			gpio_set_value(data->power_gpio, 1);
> 
> +		msleep(5);
> +
>   		data->power_state = 1;
>   		ret = tpa6130a2_initialize();
>   		if (ret < 0) {


Hello, your patch did not helped. Problem is still there...

Now I found another problem:
[   28.102233] omap_i2c 48072000.i2c: controller timed out

Anyway, if you are interested here is full dmesg log:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 4.2.0-rc2+ (pali@Pali-Latitude) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #368 
PREEMPT Sat Aug 1 12:07:46 CEST 2015
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine model: Nokia N900
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 65280
[    0.000000] free_area_init_node: node 0, pgdat c069a40c, node_mem_map cfcf9000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65280 pages, LIFO batch:15
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64768
[    0.000000] Kernel command line: rootdelay root=/dev/ram0 log_buf_len=20M
[    0.000000] log_buf_len: 33554432 bytes
[    0.000000] early log buf free: 64332(98%)
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 203424K/261120K available (4443K kernel code, 308K rwdata, 1720K rodata, 264K init, 266K bss, 
57696K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc060d0c8   (6165 kB)
[    0.000000]       .init : 0xc060e000 - 0xc0650000   ( 264 kB)
[    0.000000]       .data : 0xc0650000 - 0xc069d3dc   ( 309 kB)
[    0.000000]        .bss : 0xc069d3dc - 0xc06dfc4c   ( 267 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Clocking rate (Crystal/Core/MPU): 19.2/332/500 MHz
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns
[    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000305] Console: colour dummy device 80x30
[    0.001586] console [tty0] enabled
[    0.001647] Calibrating delay loop... 496.43 BogoMIPS (lpj=2482176)
[    0.048828] pid_max: default: 32768 minimum: 301
[    0.048980] Security Framework initialized
[    0.049102] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.049163] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050354] Initializing cgroup subsys blkio
[    0.050445] Initializing cgroup subsys freezer
[    0.050567] CPU: Testing write buffer coherency: ok
[    0.051239] Setting up static identity map for 0x80008200 - 0x80008258
[    0.054779] devtmpfs: initialized
[    0.101928] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[    0.123107] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
[    0.123840] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
[    0.173553] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.174530] pinctrl core: initialized pinctrl subsystem
[    0.176361] NET: Registered protocol family 16
[    0.177978] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.208465] cpuidle: using governor ladder
[    0.238403] cpuidle: using governor menu
[    0.239074] Reprogramming SDRC clock to 332000000 Hz
[    0.245819] OMAP GPIO hardware version 2.5
[    0.252288] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 !
[    0.252990] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 !
[    0.267974] omap-gpmc 6e000000.gpmc: could not find pctldev for node 
/ocp/l4@48000000/scm@2000/pinmux@30/pinmux_gpmc_pins, deferring probe
[    0.272857] RX-51: Enabling ARM errata 430973 workaround
[    0.274658] RX-51: Registring OMAP3 HWRNG device
[    0.278564] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.280212] Reserving DMA channels 0 and 1 for HS ROM code
[    0.280273] OMAP DMA hardware revision 4.0
[    0.330078] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
[    0.335510] omap-iommu 480bd400.mmu: 480bd400.mmu registered
[    0.336303] usbcore: registered new interface driver usbfs
[    0.336486] usbcore: registered new interface driver hub
[    0.336730] usbcore: registered new device driver usb
[    0.337860] omap_i2c 48070000.i2c: could not find pctldev for node 
/ocp/l4@48000000/scm@2000/pinmux@30/pinmux_i2c1_pins, deferring probe
[    0.338012] omap_i2c 48072000.i2c: could not find pctldev for node 
/ocp/l4@48000000/scm@2000/pinmux@30/pinmux_i2c2_pins, deferring probe
[    0.338226] omap_i2c 48060000.i2c: could not find pctldev for node 
/ocp/l4@48000000/scm@2000/pinmux@30/pinmux_i2c3_pins, deferring probe
[    0.339782] omap-mailbox 48094000.mailbox: omap mailbox rev 0x40
[    0.340423] Advanced Linux Sound Architecture Driver Initialized.
[    0.341979] clocksource: Switched to clocksource 32k_counter
[    0.383239] NET: Registered protocol family 2
[    0.384521] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.384643] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.384735] TCP: Hash tables configured (established 2048 bind 2048)
[    0.384948] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.385009] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.385314] NET: Registered protocol family 1
[    0.385864] Trying to unpack rootfs image as initramfs...
[    0.386383] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
[    0.518432] Freeing initrd memory: 15240K (ce900000 - cf7e2000)
[    0.519073] hw perfevents: Failed to parse /pmu/interrupt-affinity[0]
[    0.519226] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
[    0.523986] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.541168] VFS: Disk quotas dquot_6.6.0
[    0.541687] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.544769] io scheduler noop registered
[    0.545288] io scheduler cfq registered (default)
[    0.546813] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568
[    0.547302] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
[    0.548004] pinctrl-single 480025d8.pinmux: 18 pins at pa fa0025d8 size 36
[    0.550445] 48050000.dss supply vdda_video not found, using dummy regulator
[    0.550781] OMAP DSS rev 2.0
[    0.551452] omapdss_dss 48050000.dss: bound 48050400.dispc (ops dispc_component_ops)
[    0.551910] omapdss_dss 48050000.dss: bound 48050c00.encoder (ops venc_component_ops)
[    0.553375] omapfb omapfb: no displays
[    0.553588] omapfb omapfb: failed to setup omapfb
[    0.554199] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.557464] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    0.558685] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[    0.560394] omap3_rom_rng: initializing
[    0.586517] brd: module loaded
[    0.596771] loop: module loaded
[    0.598266] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.611114] acx565akm spi1.2: omapfb: acx565akm rev ad LCD detected
[    0.615112] HS USB OTG: no transceiver configured
[    0.615203] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
[    0.616577] i2c /dev entries driver
[    0.618164] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517
[    0.643157] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517
[    0.675903] rx51-audio n900-audio: could not get speaker enable gpio
[    0.676788] Initializing XFRM netlink socket
[    0.676940] NET: Registered protocol family 17
[    0.677062] NET: Registered protocol family 15
[    0.677185] NET: Registered protocol family 35
[    0.677429] Key type dns_resolver registered
[    0.677734] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva
[    0.677825] omap2_set_init_voltage: unable to set vdd_mpu_iva
[    0.677886] omap2_set_init_voltage: unable to find boot up OPP for vdd_core
[    0.677947] omap2_set_init_voltage: unable to set vdd_core
[    0.682861] ThumbEE CPU extension supported.
[    0.682952] SmartReflex Class3 initialized
[    0.689971] registered taskstats version 1
[    0.692565] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[    0.692657] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[    0.693359] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x01000000, virtual base d0940000, freq 66 MHz
[    0.693450] OneNAND Manufacturer: Samsung (0xec)
[    0.693481] Muxed OneNAND 256MB 1.8V 16-bit (0x40)
[    0.693542] OneNAND version = 0x0121
[    0.693572] Chip support all block unlock
[    0.693572] Chip has 2 plane
[    0.695281] Scanning device for bad blocks
[    0.795776] 6 ofpart partitions found on MTD device omap2-onenand
[    0.795837] Creating 6 MTD partitions on "omap2-onenand":
[    0.795898] 0x000000000000-0x000000020000 : "bootloader"
[    0.796783] 0x000000020000-0x000000080000 : "config"
[    0.797637] 0x000000080000-0x0000000c0000 : "log"
[    0.798370] 0x0000000c0000-0x0000002c0000 : "kernel"
[    0.799133] 0x0000002c0000-0x0000004c0000 : "initfs"
[    0.799896] 0x0000004c0000-0x000010000000 : "rootfs"
[    1.102752] twl 1-0048: PIH (irq 23) chaining IRQs 340..348
[    1.102966] twl 1-0048: power (irq 345) chaining IRQs 348..355
[    1.662963] twl4030_gpio twl4030-gpio: gpio (irq 340) chaining IRQs 356..373
[    1.922668] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: Initialized TWL4030 USB module
[    1.925415] input: twl4030_pwrbutton as 
/devices/platform/68000000.ocp/48070000.i2c/i2c-1/1-0048/48070000.i2c:twl@48:pwrbutton/input/input0
[    1.927185] input: TWL4030 Keypad as 
/devices/platform/68000000.ocp/48070000.i2c/i2c-1/1-0048/48070000.i2c:twl@48:keypad/input/input1
[    5.942382] omap_i2c 48070000.i2c: bus 1 rev3.3 at 2200 kHz
[    5.962585] tpa6130a2 2-0060: Write failed
[    5.962707] tpa6130a2 2-0060: Failed to initialize chip
[    5.962860] tpa6130a2: probe of 2-0060 failed with error -121
[    5.963439] omap_i2c 48072000.i2c: bus 2 rev3.3 at 100 kHz
[    5.965820] omap_i2c 48060000.i2c: bus 3 rev3.3 at 400 kHz
[    5.992004] Console: switching to colour frame buffer device 100x30
[    6.072662] omapfb omapfb: using display 'lcd' mode 800x480
[    6.273071] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    6.273101] musb-hdrc: MHDRC RTL version 1.400 
[    6.273132] musb-hdrc: setup fifo_mode 4
[    6.273162] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    6.574035] rx51-audio n900-audio: Failed to add TPA6130A2 controls
[    6.580657] rx51-audio n900-audio: ASoC: failed to init TLV320AIC34: -19
[    6.587554] rx51-audio n900-audio: ASoC: failed to instantiate card -19
[    6.594146] gpiod_unexport: invalid GPIO
[    6.600555] rx51-audio n900-audio: snd_soc_register_card failed (-19)
[    6.623199] hctosys: unable to open rtc device (rtc0)
[    6.629699] sr_init: No PMIC hook to init smartreflex
[    6.637237] using random self ethernet address
[    6.643829] using random host ethernet address
[    6.650268] Number of LUNs=8
[    6.657165] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
[    6.664276] Mass Storage Function, version: 2009/09/11
[    6.671386] LUN: removable file: (no medium)
[    6.678833] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
[    6.692260] Number of LUNs=2
[    6.699798] LUN: removable file: (no medium)
[    6.719238] VCSI: disabling
[    6.726684] LUN: removable file: (no medium)
[    6.733795] Number of LUNs=2
[    6.741546] g_nokia gadget: USB CDC Phonet function
[    6.748138] g_nokia gadget: using musb-hdrc, OUT ep1out, IN ep1in
[    6.755035] ALSA device list:
[    6.761291]   No soundcards found.
[    6.768676] usb0: HOST MAC 52:35:2b:7b:77:0e
[    6.775085] usb0: MAC 32:e8:ee:88:a4:58
[    6.782043] RAMDISK: cramfs filesystem found at block 0
[    6.788543] RAMDISK: Loading 15240KiB [1 disk] into ram disk... /
[    6.792358] g_nokia gadget: USB CDC Phonet function
[    6.804992] -
[    6.822235] g_nokia gadget: using musb-hdrc, OUT ep1out, IN ep1in
[    6.834808] \
[    6.852539] g_nokia gadget: N900 (PC-Suite Mode)
[    6.865417] /
[    6.872253] g_nokia gadget: g_nokia ready
[    6.885009] done.
[    7.333801] VFS: Mounted root (cramfs filesystem) readonly on device 1:0.
[    7.340911] Freeing unused kernel memory: 264K (c060e000 - c0650000)
[    7.621368] g_nokia gadget: high-speed config #1: Bus Powered
[    7.681365] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[   13.258148] omap-sham 480c3000.sham: hw accel on OMAP rev 0.9
[   13.333465] input: TSC2005 touchscreen as 
/devices/platform/68000000.ocp/48098000.spi/spi_master/spi1/spi1.0/input/input2
[   15.720733] input: twl4030:vibrator as 
/devices/platform/68000000.ocp/48070000.i2c/i2c-1/1-0048/48070000.i2c:twl@48:audio/input/input3
[   23.654785] media: Linux media interface: v0.10
[   25.393402] tsl2563 2-0029: model 7, rev. 0
[   25.772796] Linux video capture interface: v2.00
[   28.102233] omap_i2c 48072000.i2c: controller timed out
[   29.463653] lp5523x 2-0032: lp5523 Programmable led chip found
[   30.734191] omap_i2c 48072000.i2c: controller timed out waiting for start condition to finish
[   32.142333] i2c i2c-2: SCL is stuck low, exit recovery
[   33.162322] i2c i2c-2: SCL is stuck low, exit recovery
[   34.462249] i2c i2c-2: SCL is stuck low, exit recovery
[   35.482299] i2c i2c-2: SCL is stuck low, exit recovery
[   36.862762] omap_ssi 48058000.ssi-controller: ssi controller 0 initialized (1 ports)!
[   37.113800] smc91x: not found (-19).
[   37.132263] i2c i2c-2: SCL is stuck low, exit recovery
[   38.962341] i2c i2c-2: SCL is stuck low, exit recovery
[   39.122406] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC
[   39.233428] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48 as rtc0
[   39.972198] i2c i2c-2: SCL is stuck low, exit recovery
[   40.992309] i2c i2c-2: SCL is stuck low, exit recovery
[   42.050415] i2c i2c-2: SCL is stuck low, exit recovery
[   43.062316] i2c i2c-2: SCL is stuck low, exit recovery
[   44.072235] i2c i2c-2: SCL is stuck low, exit recovery
[   44.072265] si4713 2-0063: Error while sending command 0x01
[   45.092224] i2c i2c-2: SCL is stuck low, exit recovery
[   45.092254] si4713 2-0063: Error while sending command 0x10
[   45.092285] si4713 2-0063: Failed to probe device information.
[   45.092620] si4713: probe of 2-0063 failed with error -16
[   45.094757] bq27x00-battery 2-0055: support ver. 1.2.0 enabled
[   45.364929] Bluetooth: Core ver 2.20
[   45.365356] NET: Registered protocol family 31
[   45.365356] Bluetooth: HCI device and connection manager initialized
[   45.365386] Bluetooth: HCI socket layer initialized
[   45.365417] Bluetooth: L2CAP socket layer initialized
[   45.365478] Bluetooth: SCO socket layer initialized
[   46.102386] i2c i2c-2: SCL is stuck low, exit recovery
[   47.122344] i2c i2c-2: SCL is stuck low, exit recovery
[   48.212310] i2c i2c-2: SCL is stuck low, exit recovery
[   48.342651] lis3lv02d: 8 bits sensor found
[   48.473175] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input4
[   49.402313] i2c i2c-2: SCL is stuck low, exit recovery
[   50.422302] i2c i2c-2: SCL is stuck low, exit recovery
[   51.442291] i2c i2c-2: SCL is stuck low, exit recovery
[   52.462219] i2c i2c-2: SCL is stuck low, exit recovery
[   53.668853] i2c i2c-2: SCL is stuck low, exit recovery
[   54.682312] i2c i2c-2: SCL is stuck low, exit recovery
[   54.882263] random: nonblocking pool is initialized
[   55.692291] i2c i2c-2: SCL is stuck low, exit recovery
[   56.220550] isp1704_charger isp1704: init gpio 67
[   56.342437] isp1704_charger isp1704: registered with product id isp1707
[   56.702209] i2c i2c-2: SCL is stuck low, exit recovery
[   57.674682] g_nokia gadget: high-speed config #1: Bus Powered
[   57.823730] i2c i2c-2: SCL is stuck low, exit recovery
[   59.412292] i2c i2c-2: SCL is stuck low, exit recovery
[   59.412322] bq2415x-charger 2-006b: failed to set default values: -16
[   89.415588] cfg80211: Calling CRDA to update world regulatory domain
[   93.862243] cfg80211: Calling CRDA to update world regulatory domain
[   97.128662] cfg80211: Calling CRDA to update world regulatory domain
[  100.392242] cfg80211: Calling CRDA to update world regulatory domain
[  104.742370] cfg80211: Calling CRDA to update world regulatory domain
[  105.832824] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[  105.873840] wl1251: loaded
[  107.223327] wl1251: initialized
[  108.932312] cfg80211: Calling CRDA to update world regulatory domain
[  113.012298] cfg80211: Calling CRDA to update world regulatory domain
[  117.022308] cfg80211: Calling CRDA to update world regulatory domain
[  120.962310] cfg80211: Calling CRDA to update world regulatory domain
[  124.192291] cfg80211: Calling CRDA to update world regulatory domain
[  127.362243] cfg80211: Calling CRDA to update world regulatory domain
[  131.712249] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA


-- 
Pali Rohár
pali.rohar@gmail.com

[toc] | [next] | [standalone]

#1199145

[Multipart message — attachments visible in raw view] — view raw

On Monday 03 August 2015 20:03:16 Jarkko Nikula wrote:
> Hi
> 
> On 08/01/2015 01:18 PM, Pali Rohár wrote:
> > On Saturday 25 July 2015 15:17:13 Lars-Peter Clausen wrote:
> >> On 07/25/2015 12:28 PM, Pali Rohár wrote:
> >>> Hello,
> >>> 
> >>> sometimes after rebooting Nokia N900 initializing alsa audio
> >>> fails. Here output from dmesg log when it happen:
> >>> 
> >>> [    6.925140] tpa6130a2 2-0060: Write failed
> >>> [    6.929534] tpa6130a2 2-0060: Failed to initialize chip
> >>> [    6.935272] tpa6130a2: probe of 2-0060 failed with error -121
> >>> [    7.624237] rx51-audio n900-audio: Failed to add TPA6130A2
> >>> controls [    7.635101] rx51-audio n900-audio: ASoC: failed to
> >>> init TLV320AIC34: -19 [    7.645874] rx51-audio n900-audio: ASoC:
> >>> failed to instantiate card -19 [    7.665740] rx51-audio
> >>> n900-audio: snd_soc_register_card failed (-19) [    8.063049]
> >>> ALSA device list:
> >>> [    8.070343]   No soundcards found.
> >>> 
> >>> Any idea what to do?
> >> 
> >> Looks like the chip is not responding. Try to add a small delay
> >> after powerup to give the device to be fully ready, something
> >> like the following:
> >> 
> >> --- a/sound/soc/codecs/tpa6130a2.c
> >> +++ b/sound/soc/codecs/tpa6130a2.c
> >> @@ -152,6 +152,8 @@ static int tpa6130a2_power(u8 power)
> >> 
> >>   		if (data->power_gpio >= 0)
> >>   		
> >>   			gpio_set_value(data->power_gpio, 1);
> >> 
> >> +		msleep(5);
> >> +
> >> 
> >>   		data->power_state = 1;
> >>   		ret = tpa6130a2_initialize();
> >>   		if (ret < 0) {
> > 
> > Hello, your patch did not helped. Problem is still there...
> 
> For me v4.2-rc5 works, i.e. TPA6130A2 can still play loudly to
> headphones. Don't know were there any i2c etc regression before it or
> how easy it would be to reproduce.
> 

Did you tested it on Nokia N900? Or other device?

> Logs below made me thinking can it be a HW issue? Although if it is
> an HW issue it shouldn't work sometimes I guess. Do you have any
> earlier well known configuration you could try is it an SW
> regression or something else?
> 

Stock Nokia's 2.6.28 kernel works always. With that kernel I have never 
seen this problem. So I do not think this is HW problem.

This problem is there in more kernel versions, maybe in some older (like 
v3.5) is was there not so often. But do not remember correctly...

> > [    5.962585] tpa6130a2 2-0060: Write failed
> > [    5.962707] tpa6130a2 2-0060: Failed to initialize chip
> > [    5.962860] tpa6130a2: probe of 2-0060 failed with error -121
> 
> -121 == EREMOTEIO which is returned from i2c-omap.c when there is no
> ACK from the chip.
> 

Maybe some power management problem? Something is not always initialized 
correctly?

I remember that there is some problem (maybe in NoLo - Nokia bootloader) 
that sometimes chainloaded U-Boot (booted via NoLo) is not able to 
initialize mmc chip (all read operation fails). In U-Boot I added some 
code to enable some parts in twl4030 regulator and after that mmc is 
working always...

So maybe something similar? Kernel expects that some PM or regulator 
parts are initialized, but they are only sometimes? Just speculation...

> > [   28.102233] omap_i2c 48072000.i2c: controller timed out
> > [   29.463653] lp5523x 2-0032: lp5523 Programmable led chip found
> > [   30.734191] omap_i2c 48072000.i2c: controller timed out waiting
> > for start condition to finish [   32.142333] i2c i2c-2: SCL is
> > stuck low, exit recovery
> 
> If SCL is really stuck it also explains why chip doesn't acknowledge.

-- 
Pali Rohár
pali.rohar@gmail.com

[toc] | [prev] | [next] | [standalone]

#1199183

On 08/03/2015 09:17 PM, Pali Rohár wrote:
> On Monday 03 August 2015 20:03:16 Jarkko Nikula wrote:
>> Hi
>>
>> On 08/01/2015 01:18 PM, Pali Rohár wrote:
>>> On Saturday 25 July 2015 15:17:13 Lars-Peter Clausen wrote:
>>> Hello, your patch did not helped. Problem is still there...
>>
>> For me v4.2-rc5 works, i.e. TPA6130A2 can still play loudly to
>> headphones. Don't know were there any i2c etc regression before it or
>> how easy it would be to reproduce.
>>
> 
> Did you tested it on Nokia N900? Or other device?
> 
N900. Seems to be only user of TPA6130A2 in mainline :-)

>> Logs below made me thinking can it be a HW issue? Although if it is
>> an HW issue it shouldn't work sometimes I guess. Do you have any
>> earlier well known configuration you could try is it an SW
>> regression or something else?
>>
> 
> Stock Nokia's 2.6.28 kernel works always. With that kernel I have never 
> seen this problem. So I do not think this is HW problem.
> 
> This problem is there in more kernel versions, maybe in some older (like 
> v3.5) is was there not so often. But do not remember correctly...
>
It is well possible that some regression got introduced to TPA6130A2 I2C
communication over the years without nobody than you now notices. We
used to do QA back in Meego N900 days but that was pre 3.x kernels.

> Maybe some power management problem? Something is not always initialized 
> correctly?
> 
> I remember that there is some problem (maybe in NoLo - Nokia bootloader) 
> that sometimes chainloaded U-Boot (booted via NoLo) is not able to 
> initialize mmc chip (all read operation fails). In U-Boot I added some 
> code to enable some parts in twl4030 regulator and after that mmc is 
> working always...
> 
> So maybe something similar? Kernel expects that some PM or regulator 
> parts are initialized, but they are only sometimes? Just speculation...
>
I'm thinking the same. I could figure SCL could be stuck low if TPA or
some other chip connected to the same I2C bus is without power and is
pulling I2C signals down.

-- 
Jarkko
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[toc] | [prev] | [next] | [standalone]

#1199186

[Multipart message — attachments visible in raw view] — view raw

On Monday 03 August 2015 20:48:28 Jarkko Nikula wrote:
> On 08/03/2015 09:17 PM, Pali Rohár wrote:
> > On Monday 03 August 2015 20:03:16 Jarkko Nikula wrote:
> >> Hi
> >> 
> >> On 08/01/2015 01:18 PM, Pali Rohár wrote:
> >>> On Saturday 25 July 2015 15:17:13 Lars-Peter Clausen wrote:
> >>> Hello, your patch did not helped. Problem is still there...
> >> 
> >> For me v4.2-rc5 works, i.e. TPA6130A2 can still play loudly to
> >> headphones. Don't know were there any i2c etc regression before it
> >> or how easy it would be to reproduce.
> > 
> > Did you tested it on Nokia N900? Or other device?
> 
> N900. Seems to be only user of TPA6130A2 in mainline :-)
> 

Great, can you do more tests? I get this error often after I reboot N900 
(without power off) more times. But no idea if this is just "sometimes".

> >> Logs below made me thinking can it be a HW issue? Although if it
> >> is an HW issue it shouldn't work sometimes I guess. Do you have
> >> any earlier well known configuration you could try is it an SW
> >> regression or something else?
> > 
> > Stock Nokia's 2.6.28 kernel works always. With that kernel I have
> > never seen this problem. So I do not think this is HW problem.
> > 
> > This problem is there in more kernel versions, maybe in some older
> > (like v3.5) is was there not so often. But do not remember
> > correctly...
> 
> It is well possible that some regression got introduced to TPA6130A2
> I2C communication over the years without nobody than you now
> notices. We used to do QA back in Meego N900 days but that was pre
> 3.x kernels.
> 

Do you still have these pre 3.x kernels? This could be good starting 
point as 2.6.28 kernel is tooo old and heavily patches...

> > Maybe some power management problem? Something is not always
> > initialized correctly?
> > 
> > I remember that there is some problem (maybe in NoLo - Nokia
> > bootloader) that sometimes chainloaded U-Boot (booted via NoLo) is
> > not able to initialize mmc chip (all read operation fails). In
> > U-Boot I added some code to enable some parts in twl4030 regulator
> > and after that mmc is working always...
> > 
> > So maybe something similar? Kernel expects that some PM or
> > regulator parts are initialized, but they are only sometimes? Just
> > speculation...
> 
> I'm thinking the same. I could figure SCL could be stuck low if TPA
> or some other chip connected to the same I2C bus is without power
> and is pulling I2C signals down.

We should know which devices are connected to which i2c bus. So maybe 
detecting which i2c device is incorrectly initialized?

-- 
Pali Rohár
pali.rohar@gmail.com

[toc] | [prev] | [next] | [standalone]

#1199461

On 08/03/2015 09:48 PM, Jarkko Nikula wrote:
> It is well possible that some regression got introduced to TPA6130A2 I2C
> communication over the years without nobody than you now notices. We
> used to do QA back in Meego N900 days but that was pre 3.x kernels.

No major changes has been done to the tpa driver during the past years... I
wanted to do some updates, like moving it to regmap, but as you said, n900 is
the only user (and n9) and I do not feel comfortable to hack on a device where
I do not have serial console... And I'm using the n900 time to time also.

>> So maybe something similar? Kernel expects that some PM or regulator 
>> parts are initialized, but they are only sometimes? Just speculation...
>>
> I'm thinking the same. I could figure SCL could be stuck low if TPA or
> some other chip connected to the same I2C bus is without power and is
> pulling I2C signals down.

What would happen with the SCL stuck on i2c.2 bus if you remove the tpa driver
from the kernel? If you remove the other drivers for the devices on i2c.2?

-- 
Péter
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[toc] | [prev] | [next] | [standalone]

#1199153

Hi

On 08/01/2015 01:18 PM, Pali Rohár wrote:
> On Saturday 25 July 2015 15:17:13 Lars-Peter Clausen wrote:
>> On 07/25/2015 12:28 PM, Pali Rohár wrote:
>>> Hello,
>>>
>>> sometimes after rebooting Nokia N900 initializing alsa audio fails.
>>> Here output from dmesg log when it happen:
>>>
>>> [    6.925140] tpa6130a2 2-0060: Write failed
>>> [    6.929534] tpa6130a2 2-0060: Failed to initialize chip
>>> [    6.935272] tpa6130a2: probe of 2-0060 failed with error -121
>>> [    7.624237] rx51-audio n900-audio: Failed to add TPA6130A2
>>> controls [    7.635101] rx51-audio n900-audio: ASoC: failed to
>>> init TLV320AIC34: -19 [    7.645874] rx51-audio n900-audio: ASoC:
>>> failed to instantiate card -19 [    7.665740] rx51-audio
>>> n900-audio: snd_soc_register_card failed (-19) [    8.063049] ALSA
>>> device list:
>>> [    8.070343]   No soundcards found.
>>>
>>> Any idea what to do?
>>
>> Looks like the chip is not responding. Try to add a small delay after
>> powerup to give the device to be fully ready, something like the
>> following:
>>
>> --- a/sound/soc/codecs/tpa6130a2.c
>> +++ b/sound/soc/codecs/tpa6130a2.c
>> @@ -152,6 +152,8 @@ static int tpa6130a2_power(u8 power)
>>   		if (data->power_gpio >= 0)
>>   			gpio_set_value(data->power_gpio, 1);
>>
>> +		msleep(5);
>> +
>>   		data->power_state = 1;
>>   		ret = tpa6130a2_initialize();
>>   		if (ret < 0) {
> 
> 
> Hello, your patch did not helped. Problem is still there...
> 
For me v4.2-rc5 works, i.e. TPA6130A2 can still play loudly to
headphones. Don't know were there any i2c etc regression before it or
how easy it would be to reproduce.

Logs below made me thinking can it be a HW issue? Although if it is an
HW issue it shouldn't work sometimes I guess. Do you have any earlier
well known configuration you could try is it an SW regression or
something else?

> [    5.962585] tpa6130a2 2-0060: Write failed
> [    5.962707] tpa6130a2 2-0060: Failed to initialize chip
> [    5.962860] tpa6130a2: probe of 2-0060 failed with error -121

-121 == EREMOTEIO which is returned from i2c-omap.c when there is no ACK
from the chip.

> [   28.102233] omap_i2c 48072000.i2c: controller timed out
> [   29.463653] lp5523x 2-0032: lp5523 Programmable led chip found
> [   30.734191] omap_i2c 48072000.i2c: controller timed out waiting for start condition to finish
> [   32.142333] i2c i2c-2: SCL is stuck low, exit recovery

If SCL is really stuck it also explains why chip doesn't acknowledge.

-- 
Jarkko
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

[toc] | [prev] | [standalone]

Back to top | Article view | linux.kernel

csiph-web