Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]


Groups > linux.kernel > #1703328

Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics

From Andrew Lunn <andrew@lunn.ch>
Newsgroups linux.kernel
Subject Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics
Date 2017-08-03 20:20 +0200
Message-ID <uasSZ-3Ii-7@gated-at.bofh.it> (permalink)
References <u9Nwt-1j6-11@gated-at.bofh.it> <uabyN-8qn-13@gated-at.bofh.it> <uasgh-3eZ-5@gated-at.bofh.it>
Organization linux.* mail to news gateway

Show all headers | View raw


On Thu, Aug 03, 2017 at 10:30:56AM -0700, Florian Fainelli wrote:
> On 08/02/2017 04:49 PM, David Miller wrote:
> > From: Florian Fainelli <f.fainelli@gmail.com>
> > Date: Tue,  1 Aug 2017 15:00:36 -0700
> > 
> >> DSA slave network devices maintain a pair of bytes and packets counters
> >> for each directions, but these are not 64-bit capable. Re-use
> >> pcpu_sw_netstats which contains exactly what we need for that purpose
> >> and update the code path to report 64-bit capable statistics.
> >>
> >> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
> > 
> > Applied, thanks.
> > 
> > I would run ethtool -S and ifconfig under perf to see where it is
> > spending so much time.
> > 
> 
> This appears to be way worse than I thought, will keep digging, but for
> now, I may have to send a revert. Andrew, Vivien can you see if you have
> the same problems on your boards? Thanks!
> 
> # killall iperf
> # [ ID] Interval       Transfer     Bandwidth
> [  3]  0.0-19.1 sec   500 MBytes   220 Mbits/sec
> # while true; do ethtool -S gphy; ifconfig gphy; done
> ^C^C
> 
> 
> [   64.566226] INFO: rcu_sched self-detected stall on CPU
> [   64.571487]  0-...: (25999 ticks this GP) idle=006/140000000000001/0

Hi Florian

I don't get anything so bad, but i think that is because of hardware
restrictions. I see the ethtool; ifconfig loop goes a lot slower when
there is iperf traffic, but i don't get an RCU stall. However, the
board i tested on only has a 100Mbps CPU interface, and it can handle
all that traffic without pushing the CPU to 100%. What is the CPU load
when you run your test? Even if you are going to 100% CPU load, we
still don't want RCU stalls.

      Andrew

Back to linux.kernel | Previous | NextPrevious in thread | Next in thread | Find similar | Unroll thread


Thread

[PATCH net-next] net: dsa: Add support for 64-bit statistics Florian Fainelli <f.fainelli@gmail.com> - 2017-08-02 00:10 +0200
  Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics Florian Fainelli <f.fainelli@gmail.com> - 2017-08-02 00:50 +0200
  Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics David Miller <davem@davemloft.net> - 2017-08-03 01:50 +0200
    Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics Florian Fainelli <f.fainelli@gmail.com> - 2017-08-03 19:40 +0200
      Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics Andrew Lunn <andrew@lunn.ch> - 2017-08-03 20:20 +0200
        Re: [PATCH net-next] net: dsa: Add support for 64-bit statistics Florian Fainelli <f.fainelli@gmail.com> - 2017-08-03 21:50 +0200

csiph-web