Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]
Groups > linux.kernel > #1661665
| From | Tim Harvey <tharvey@gateworks.com> |
|---|---|
| Newsgroups | linux.kernel |
| Subject | Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder |
| Date | 2017-06-08 22:30 +0200 |
| Message-ID | <tQce6-vS-33@gated-at.bofh.it> (permalink) |
| References | <tPO26-1PO-7@gated-at.bofh.it> <tPO27-1PO-39@gated-at.bofh.it> |
| Organization | linux.* mail to news gateway |
On Wed, Jun 7, 2017 at 11:33 AM, Steve Longerbeam <slongerbeam@gmail.com> wrote:
> Enables the ADV7180 decoder sensor. The ADV7180 connects to the
> parallel-bus mux input on ipu1_csi0_mux.
>
> The ADV7180 power pin is via max7310_b port expander.
>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
>
> - Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity.
> - For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used.
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---
> arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 50 ++++++++++++++++++++++++++++++++
> 1 file changed, 50 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> index 1212f82..c24af28 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
> @@ -124,6 +124,21 @@
> #size-cells = <0>;
> reg = <1>;
>
> + adv7180: camera@21 {
> + compatible = "adi,adv7180";
> + reg = <0x21>;
> + powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> +
> + port {
> + adv7180_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> + bus-width = <8>;
> + };
> + };
> + };
> +
> max7310_a: gpio@30 {
> compatible = "maxim,max7310";
> reg = <0x30>;
> @@ -151,6 +166,25 @@
> };
> };
>
> +&ipu1_csi0_from_ipu1_csi0_mux {
> + bus-width = <8>;
> +};
> +
> +&ipu1_csi0_mux_from_parallel_sensor {
> + remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
> + bus-width = <8>;
> +};
> +
> +&ipu1_csi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_csi0>;
> +
> + /* enable frame interval monitor on this port */
> + fim {
> + status = "okay";
> + };
Steve,
You need to remove the fim node now that you've moved this to V4L2 controls.
Regards,
Tim
Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread
[PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Steve Longerbeam <slongerbeam@gmail.com> - 2017-06-07 20:40 +0200
Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Tim Harvey <tharvey@gateworks.com> - 2017-06-08 22:30 +0200
Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Steve Longerbeam <slongerbeam@gmail.com> - 2017-06-08 22:40 +0200
Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Pavel Machek <pavel@ucw.cz> - 2017-06-09 23:40 +0200
Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Steve Longerbeam <slongerbeam@gmail.com> - 2017-06-10 00:40 +0200
Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Pavel Machek <pavel@ucw.cz> - 2017-06-10 01:30 +0200
Re: [PATCH v8 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Steve Longerbeam <slongerbeam@gmail.com> - 2017-06-10 02:20 +0200
[PATCH v9 14/34] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder Steve Longerbeam <slongerbeam@gmail.com> - 2017-06-09 01:50 +0200
csiph-web