Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1485911

Re: [RFC PATCH v2 1/2] ARM: dts: samsung: add rga-lvds panel in itop elite

Show all headers | View raw

On Sun, Sep 18, 2016 at 09:03:48PM +0200, Krzysztof Kozlowski wrote:
> On Sun, Sep 18, 2016 at 10:27:38PM +0800, Randy Li wrote:
> > It is actually a lvds panel connected through a rga-lvds bridge.
> > The touchscreen is communicated with i2c bus but the driver is not
> > support now.
> > 
> > Signed-off-by: Randy Li <ayaka@soulik.info>
> 
> Subject: ARM: dts: exynos
> 
> > ---
> >  arch/arm/boot/dts/exynos4412-itop-elite.dts | 54 +++++++++++++++++++++++++++--
> >  1 file changed, 52 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts
> > index b08705e..9ef0505 100644
> > --- a/arch/arm/boot/dts/exynos4412-itop-elite.dts
> > +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts
> > @@ -138,6 +138,36 @@
> >  		assigned-clocks = <&clock CLK_MOUT_CAM0>;
> >  		assigned-clock-parents = <&clock CLK_XUSBXTI>;
> >  	};
> > +
> > +	vcc_sys_lcd: sys-lcd {
> 
> No underscores, use hyphens.

Ah wait, it's a label, so underscore seems ok. My mistake.

> 
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vcc_5v";
> > +		regulator-min-microvolt = <5000000>;
> > +		regulator-max-microvolt = <5000000>;
> > +		gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
> 
> Isn't this one of S5M8767 PMIC regulators? If so, then it should be
> defined there... On the other hand, the PMIC supports GPIO enable
> control only for buck9...
> 
> > +	};
> > +
> > +	panel: panel@0 {
> > +		compatible = "chunghwa,claa070wp03xg";
> > +
> > +		power-supply = <&vcc_sys_lcd>;
> > +		enable-gpios = <&gpl0 2 GPIO_ACTIVE_HIGH>;
> > +		backlight = <&bl>;
> > +
> > +		port {
> > +			lcd_ep: endpoint {
> 
> lcd-ep

No need, the same.

Best regards,
Krzysztof

> 
> > +				remote-endpoint = <&rga_lvds>;
> > +			};
> > +		};
> > +	};
> > +
> > +	bl: backlight {
> > +		compatible = "pwm-backlight";
> > +		pwms = <&pwm 1 5000000 PWM_POLARITY_INVERTED>;
> > +		brightness-levels = <0 5 12 16 32 64 128 255>;
> > +		default-brightness-level = <5>;
> > +		power-supply = <&vcc_sys_lcd>;
> > +	};
> >  };
> >  
> >  &adc {
> > @@ -215,9 +245,9 @@
> >  
> >  &pwm {
> >  	status = "okay";
> > -	pinctrl-0 = <&pwm0_out>;
> > +	pinctrl-0 = <&pwm0_out &pwm1_out>;
> >  	pinctrl-names = "default";
> > -	samsung,pwm-outputs = <0>;
> > +	samsung,pwm-outputs = <0>, <1>;
> >  };
> >  
> >  &sdhci_2 {
> > @@ -238,3 +268,23 @@
> >  &serial_2 {
> >  	status = "okay";
> >  };
> > +
> > +&i2c_3 {
> > +	status = "okay";
> > +};
> > +
> > +&fimd {
> 
> Please put these nodes in alphabetical order. I asked about it for
> initial DTS and it applies still.
> 
> > +	pinctrl-0 = <&lcd_clk &lcd_data24>;
> > +	pinctrl-names = "default";
> > +	status = "okay";
> > +	ports {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		port@3 {
> > +			reg = <3>;
> > +			rga_lvds: endpoint {
> 
> rga-lvds
> 
> Best regards,
> Krzysztof
> 
> > +				remote-endpoint = <&lcd_ep>;
> > +			};
> > +		};
> > +	};
> > +};
> > -- 
> > 2.7.4
> > 

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

[RFC PATCH v2 0/2] adding panel claa070wp03xg support for exynos Randy Li <ayaka@soulik.info> - 2016-09-18 16:30 +0200
  [RFC PATCH v2 1/2] ARM: dts: samsung: add rga-lvds panel in itop elite Randy Li <ayaka@soulik.info> - 2016-09-18 16:30 +0200
    Re: [RFC PATCH v2 1/2] ARM: dts: samsung: add rga-lvds panel in itop  elite Krzysztof Kozlowski <krzk@kernel.org> - 2016-09-18 21:10 +0200
      Re: [RFC PATCH v2 1/2] ARM: dts: samsung: add rga-lvds panel in itop  elite Krzysztof Kozlowski <krzk@kernel.org> - 2016-09-18 21:10 +0200
  [RFC PATCH v2 2/2] drm/panel: Add support for Chunghwa CLAA070WP03XG panel Randy Li <ayaka@soulik.info> - 2016-09-18 16:30 +0200

csiph-web