Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1546753

Re: [PATCH 1/2] drm/panel: Add support for S6E3HA2 panel driver on TM2 board

Show key headers only | View raw

On 12/20/2016 03:55 AM, Rob Herring wrote:
> On Wed, Dec 14, 2016 at 03:04:04PM +0900, Hoegeun Kwon wrote:
>> This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
>> driver. This panel has 1440x2560 resolution in 5.7-inch physical
>> panel in the TM2 device.
>>
>> Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
>> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
>> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
>> ---
>>   .../bindings/display/panel/samsung,s6e3ha2.txt     |  52 ++
>>   drivers/gpu/drm/panel/Kconfig                      |   6 +
>>   drivers/gpu/drm/panel/Makefile                     |   1 +
>>   drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c      | 756 +++++++++++++++++++++
>>   4 files changed, 815 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
>>   create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
>>
>> diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
>> new file mode 100644
>> index 0000000..1f41f24
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
>> @@ -0,0 +1,52 @@
>> +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
>> +
>> +Required properties:
>> +  - compatible: "samsung,s6e3ha2"
>> +  - reg: the virtual channel number of a DSI peripheral
>> +  - vdd3-supply: core voltage supply
>> +  - vci-supply: voltage supply for analog circuits
>> +  - reset-gpios: a GPIO spec for the reset pin
>> +  - enable-gpios: a GPIO spec for the panel enable pin
>> +  - te-gpios: a GPIO spec for the tearing effect synchronization signal gpio pin
> Need to specify the GPIOs as active high or low.

Hi Rob Herring,

Thanks for point out. I will add "(active high or low)" after the 
description of the GPIOs.

>> +
>> +Optional properties:
>> +  - display-timings: timings for the connected panel as described by [1]
>> +
>> +The device node can contain one 'port' child node with one child
>> +'endpoint' node, according to the bindings defined in [2]. This
>> +node should describe panel's video bus.
>> +
>> +[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
>> +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
>> +
>> +Example:
>> +
>> +	panel@0 {
>> +		compatible = "samsung,s6e3ha2";
>> +		reg = <0>;
> reg doesn't really work here unless this node is a child of the DSI
> controller node. But if it is a child node, then you don't need the OF
> graph.

The reg value is used in virtual child panel node so I think the reg 
value is needed.
Please refer to the document below.
Documentation/devicetree/bindings/display/mipi-dsi-bus.txt

Best Regards,
Hoegeun Kwon

>> +		vdd3-supply = <&ldo27_reg>;
>> +		vci-supply = <&ldo28_reg>;
>> +		reset-gpios = <&gpg0 0 GPIO_ACTIVE_HIGH>;
>> +		enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
>> +		te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
>> +
>> +		display-timings {
>> +			timing-0 {
>> +				clock-frequency = <0>;
>> +				hactive = <1440>;
>> +				vactive = <2560>;
>> +				hfront-porch = <1>;
>> +				hback-porch = <1>;
>> +				hsync-len = <1>;
>> +				vfront-porch = <1>;
>> +				vback-porch = <15>;
>> +				vsync-len = <1>;
>> +			};
>> +		};
>> +
>> +		port {
>> +			dsi_in: endpoint {
>> +				remote-endpoint = <&dsi_out>;
>> +			};
>> +		};
>> +	};
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

Back to linux.kernel | Previous | Next — Previous in thread | Find similar | Unroll thread

Thread

[PATCH 0/2] Add support for the S6E3HA2 panel on TM2 board Hoegeun Kwon <hoegeun.kwon@samsung.com> - 2016-12-14 07:10 +0100
  [PATCH 2/2] arm64: dts: exynos: Add support for S6E3HA2 panel device  on TM2 board Hoegeun Kwon <hoegeun.kwon@samsung.com> - 2016-12-14 07:10 +0100
  [PATCH 1/2] drm/panel: Add support for S6E3HA2 panel driver on TM2  board Hoegeun Kwon <hoegeun.kwon@samsung.com> - 2016-12-14 07:10 +0100
    Re: [PATCH 1/2] drm/panel: Add support for S6E3HA2 panel driver on TM2  board Andrzej Hajda <a.hajda@samsung.com> - 2016-12-14 15:20 +0100
      Re: [PATCH 1/2] drm/panel: Add support for S6E3HA2 panel driver on TM2  board hoegeun kwon <hoegeun.kwon@samsung.com> - 2016-12-15 03:00 +0100
    Re: [PATCH 1/2] drm/panel: Add support for S6E3HA2 panel driver on  TM2 board Rob Herring <robh@kernel.org> - 2016-12-19 20:00 +0100
      Re: [PATCH 1/2] drm/panel: Add support for S6E3HA2 panel driver on TM2  board hoegeun kwon <hoegeun.kwon@samsung.com> - 2016-12-23 06:20 +0100

csiph-web