Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1527816

Re: wl1251 & mac address & calibration data

Show all headers | View raw

[Multipart message — attachments visible in raw view] - view raw

On Tuesday 22 November 2016 17:14:28 Michal Kazior wrote:
> On 22 November 2016 at 16:31, Pali Rohár <pali.rohar@gmail.com> wrote:
> > On Tuesday 22 November 2016 16:22:57 Michal Kazior wrote:
> >> On 21 November 2016 at 16:51, Pali Rohár <pali.rohar@gmail.com>
> >> wrote:
> >> > On Friday 11 November 2016 18:20:50 Pali Rohár wrote:
> >> >> Hi! I will open discussion about mac address and calibration
> >> >> data for wl1251 wireless chip again...
> >> >> 
> >> >> Problem: Mac address & calibration data for wl1251 chip on
> >> >> Nokia N900 are stored on second nand partition (mtd1) in
> >> >> special proprietary format which is used only for Nokia N900
> >> >> (probably on N8x0 and N9 too). Wireless driver wl1251.ko
> >> >> cannot work without mac address and calibration data.
> >> 
> >> Same problem applies to some ath9k/ath10k supported routers. Some
> >> even carry mac address as implicit offset from ethernet mac
> >> address. As far as I understand OpenWRT cooks cal blobs on first
> >> boot prior to loading modules.
> > 
> > So... wl1251 on Nokia N900 is not alone and this problem is there
> > for more drivers and devices. Which means we should come up with
> > some generic solution.
> 
> This isn't particularly a problem for ath9k/ath10k.
> 
> Let me give you more background on ath10k.
> 
> ath10k devices can come with caldata and macaddr stored in their
> OTP/EEPROM. In that case a generic "template" board file is used.
> Userspace doesn't need to do anything special.
> 
> Some vendors however decide to use flash partition to store caldata.
> In that case ath10k expects userspace to prepare
> cal-$bus-$devname.bin files, each for a different radio (you can
> have multiple radios on a system).
> 
> Now translating this for wl1251 I would expect it should also use
> something like wl1251-nvs-sdio-0x0001.bin for devices like N900 that
> have caldata on flash partition (instead of the generic
> wl1251-nvs.bin). I'm not sure if wl1251-nvs.bin is something
> comparable to (the generic) board.bin ath10k has though. Maybe the
> entire idea behind wl1251-nvs.bin is flawed as it's supposed to be
> device specific and is oblivious to possibility of having multiple
> wl1251 radios on one system (probably sane assumption from practical
> standpoint but still).

Basically nvs data are device specific, in ideal case they should be 
generated in factory by some calibration process (or so).

> >> >> Absence of mac address cause that driver generates random mac
> >> >> address at every kernel boot which has couple of problems
> >> >> (unstable identifier of wireless device due to udev permanent
> >> >> storage rules; unpredictable behaviour for dhcp mac address
> >> >> assignment, mac address filtering, ...).
> >> >> 
> >> >> Currently there is no way to set (permanent) mac address for
> >> >> network interface from userspace. And it does not make sense
> >> >> to implement in linux kernel large parser for proprietary
> >> >> format of second nand partition where is mac address stored
> >> >> only for one device -- Nokia N900.
> >> >> 
> >> >> Driver wl1251.ko loads calibration data via request_firmware()
> >> >> for file wl1251-nvs.bin. There are some "example" calibration
> >> >> file in linux- firmware repository, but it is not suitable for
> >> >> normal usage as real calibration data are per-device specific.
> >> 
> >> You could hook up a script that cooks up the cal/mac file via
> >> modprobe's install hook, no?
> > 
> > Via modprobe hook I can either pass custom module parameter or call
> > any other system (shell) commands.
> > 
> > As wl1251.ko does not accept mac_address as module parameter, such
> > modprobe hook does not help -- as there is absolutely no way from
> > userspace to set or change (permanent) mac address.
> 
> Quoting modprobe.d manual:
> >       install modulename command...
> >       
> >           This command instructs modprobe to run your
> >           command instead of inserting the module in the
> >           kernel as normal. The command can be any shell
> >           command: this allows you to do any kind of
> >           complex processing you might wish. [...]

I know. But this do not allow me to send mac address to kernel -- as 
kernel does not support such command yet (reason for my first question).

> You can hook up a script that cooks up wl1251-nvs.bin (caldata,
> macaddr) and then insmod the actual wl1251.ko module. Or you can just
> cook up the nvs on first device boot and store it in /lib/firmware
> (possibly overwriting the "generic" wl1251 from linux-firmware).

This is what I would like to prevent -- overwriting (possible readonly) 
system files with some device specific. It is really bad idea!

-- 
Pali Rohár
pali.rohar@gmail.com

Back to linux.kernel | Previous | Next — Previous in thread | Next in thread | Find similar | Unroll thread

Thread

Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-21 17:00 +0100
  Re: wl1251 & mac address & calibration data Michal Kazior <michal.kazior@tieto.com> - 2016-11-22 16:30 +0100
    Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-22 16:40 +0100
      Re: wl1251 & mac address & calibration data Michal Kazior <michal.kazior@tieto.com> - 2016-11-22 17:30 +0100
        Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-22 19:10 +0100
          Re: wl1251 & mac address & calibration data Arend Van Spriel <arend.vanspriel@broadcom.com> - 2016-11-23 09:30 +0100
          Re: wl1251 & mac address & calibration data Pavel Machek <pavel@ucw.cz> - 2016-11-23 23:30 +0100
            Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-23 23:50 +0100
              Re: wl1251 & mac address & calibration data Pavel Machek <pavel@ucw.cz> - 2016-11-24 09:00 +0100
                Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-24 09:40 +0100
                Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-24 16:30 +0100
                Re: wl1251 & mac address & calibration data Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> - 2016-11-24 16:40 +0100
                Re: wl1251 & mac address & calibration data Sebastian Reichel <sre@kernel.org> - 2016-11-24 17:10 +0100
                Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-24 17:50 +0100
                Re: wl1251 & mac address & calibration data Sebastian Reichel <sre@kernel.org> - 2016-11-24 19:20 +0100
                Re: wl1251 & mac address & calibration data Pali Rohár <pali.rohar@gmail.com> - 2016-11-24 19:40 +0100
                Re: wl1251 & mac address & calibration data Aaro Koskinen <aaro.koskinen@iki.fi> - 2016-11-24 20:10 +0100
                Re: wl1251 & mac address & calibration data Sebastian Reichel <sre@kernel.org> - 2016-11-24 16:30 +0100

csiph-web