Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.kernel > #1336170

Re: [PATCH V3 3/4] 8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART support

Show all headers | View raw

Hi Andy,

Andy Shevchenko 於 2016/2/16 下午 05:11 寫道:
> On Tue, 2016-02-16 at 14:55 +0800, Peter Hung wrote:
>> +static u32 baudrate_table[] = { 1500000, 1152000, 921600 };
>> +static u8 clock_table[] = { F81504_CLKSEL_24_MHZ,
>> F81504_CLKSEL_18DOT46_MHZ,
>> +				F81504_CLKSEL_14DOT77_MHZ };
>
> I suggest to replace DOT by _.

ok

>> +/* We should do proper H/W transceiver setting before change to
>> RS485 mode */
>> +static int f81504_rs485_config(struct uart_port *port,
>> +			       struct serial_rs485 *rs485)
>> +{
>> +	u8 setting;
>> +	u8 *index = (u8 *) port->private_data;
>
> private_data is a type of void *, therefore no need to have an explicit
> casting.

ok


>> +static int f81504_check_baudrate(u32 baud, size_t *idx)
>> +{
>> +	size_t index;
>> +	u32 quot, rem;
>> +
>> +	for (index = 0; index < ARRAY_SIZE(baudrate_table); ++index)
>
> Post-increment is also okay.
>
>> {
>> +		/* Clock source must largeer than desire baudrate */
>> +		if (baud > baudrate_table[index])
>> +			continue;
>> +
>> +		quot = DIV_ROUND_CLOSEST(baudrate_table[index],
>> baud);
>
> So, how quot is used and is it possible to set, for example, baud rate
> as 1000000 or 576000?

The IC don't support B1000000 due to no 16MHz clock source.

The quot & rem is only use for compare, and it's must be not 0
when the code run to calculate DIV_ROUND_CLOSEST. So quot
is a redundancy here.

This function will find the suitable clock source for future use.
We'll pass suitable baud rate * 16 to port->uartclk for
serial8250_do_set_termios() to do advance divider operations.

I'll rewrite this section with remove quot and direct check
the "baudrate_table[index] % baud" divisible.


>> +	u8 tmp, *offset = (u8 *) port->private_data;
>
> Same for provate_data as above.

ok


>> +			/*
>> +			 * direct use 1.8432MHz when baudrate
>> smaller then or
>> +			 * equal 115200bps
>
> Check your style of comments in a _whole_ your series.

ok


>> +			/*
>> +			 * If it can't found suitable clock source
>> but had old
>> +			 * accpetable baudrate, we'll use it
>
> Typo: acceptable.
> Baudrate ->  baud rate.

ok

>> +	port.port.private_data = data;	/* save current idx */
>
> Not sure you need to allocate memory for that at all, or maybe use a
> struct with one member (for now).
>

We just pass the index of PCI configuration space currently. So
I just set a allocated u8 memory to private data. We'll maintain
current method.


>> +static SIMPLE_DEV_PM_OPS(f81504_serial_pm_ops,
>> f81504_serial_suspend,
>> +		f81504_serial_resume);
>> +
>> +static struct platform_driver f81504_serial_driver = {
>> +	.driver = {
>> +		.name	= F81504_SERIAL_NAME,
>> +		.owner	= THIS_MODULE,
>
> You perhaps don't need this. Check the rest of the modules.

ok


>> +config SERIAL_8250_F81504
>> +        tristate "Fintek F81504/508/512 16550 PCIE device support"
>> if EXPERT
>> +        depends on SERIAL_8250 && MFD_FINTEK_F81504_CORE
>> +        default SERIAL_8250
>> +        select RATIONAL
>
> It seems RATIONAL API is not used here.
>

This driver hadn't use RATIONAL API. I'll remove it.


Thanks for your advice.
-- 
With Best Regards,
Peter Hung

Back to linux.kernel | Previous | Next — Previous in thread | Find similar | Unroll thread

Thread

[PATCH V3 0/4] Transform Fintek PCIE driver from 8250 to MFD Peter Hung <hpeter@gmail.com> - 2016-02-16 08:00 +0100
  [PATCH V3 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO GPIOLIB support Peter Hung <hpeter@gmail.com> - 2016-02-16 08:00 +0100
    Re: [PATCH V3 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512  PCIE-to-UART/GPIO GPIOLIB support Linus Walleij <linus.walleij@linaro.org> - 2016-02-16 16:30 +0100
      Re: [PATCH V3 2/4] gpio: gpio-f81504: Add Fintek F81504/508/512  PCIE-to-UART/GPIO GPIOLIB support Peter Hung <hpeter@gmail.com> - 2016-02-17 11:20 +0100
  [PATCH V3 3/4] 8250: 8250_f81504: Add Fintek F81504/508/512 PCIE-to-UART/GPIO UART support Peter Hung <hpeter@gmail.com> - 2016-02-16 08:00 +0100
    Re: [PATCH V3 3/4] 8250: 8250_f81504: Add Fintek F81504/508/512  PCIE-to-UART/GPIO UART support Andy Shevchenko <andriy.shevchenko@linux.intel.com> - 2016-02-16 10:20 +0100
      Re: [PATCH V3 3/4] 8250: 8250_f81504: Add Fintek F81504/508/512  PCIE-to-UART/GPIO UART support Peter Hung <hpeter@gmail.com> - 2016-02-17 10:40 +0100

csiph-web