Re: [PATCH 2/2] leds-bcm6328: Swap LED ON and OFF definitions

From	Jacek Anaszewski <j.anaszewski@samsung.com>
Newsgroups	linux.kernel
Subject	Re: [PATCH 2/2] leds-bcm6328: Swap LED ON and OFF definitions
Date	2015-11-23 11:30 +0100
Message-ID	<qxWxJ-tE-33@gated-at.bofh.it> (permalink)
References	(5 earlier) <qr8tX-2jQ-7@gated-at.bofh.it> <qr8tX-2jQ-5@gated-at.bofh.it> <qrqhb-5qX-9@gated-at.bofh.it> <qv5Hc-20o-15@gated-at.bofh.it> <qv5Hc-20o-13@gated-at.bofh.it>
Organization	linux.* mail to news gateway

Show all headers | View raw

On 11/15/2015 02:34 PM, Simon Arlott wrote:
> The values of BCM6328_LED_MODE_ON and BCM6328_LED_MODE_OFF were named
> for active low LEDs. These should be swapped so that they are named for
> the default case of active high LEDs.
>
> Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
> ---
> On 05/11/15 10:41, Jacek Anaszewski wrote:
>> On 11/04/2015 04:46 PM, Álvaro Fernández Rojas wrote:
>>> BCM6328_LED_MODE_ON and BCM6328_LED_MODE_OFF values were extracted from
>>> Broadcom's GPL code, in which they assume leds are active low by default.
>>> I can confirm the code is correct as it is right now, since those values
>>> match the active high / low values of the LEDs managed by GPIO instead
>>> of by using this driver.
>>
>> BCM6328_LED_MODE_ON and BCM6328_LED_MODE_OFF should represent the values
>> that actually set the LED state according to the current logic.
>> Otherwise it will confuse people who will be analyzing this code.
>> We are interested in the logic as it is seen from this driver's
>> perspective and not GPIO perspective.
>>
>> IMO the values should be swapped.
>
>   drivers/leds/leds-bcm6328.c | 12 ++++++------
>   1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/leds/leds-bcm6328.c b/drivers/leds/leds-bcm6328.c
> index 95d0cf9..0329dee 100644
> --- a/drivers/leds/leds-bcm6328.c
> +++ b/drivers/leds/leds-bcm6328.c
> @@ -48,10 +48,10 @@
>   					 BCM6328_SERIAL_LED_SHIFT_DIR)
>
>   #define BCM6328_LED_MODE_MASK		3
> -#define BCM6328_LED_MODE_OFF		0
> +#define BCM6328_LED_MODE_ON		0
>   #define BCM6328_LED_MODE_FAST		1
>   #define BCM6328_LED_MODE_BLINK		2
> -#define BCM6328_LED_MODE_ON		3
> +#define BCM6328_LED_MODE_OFF		3
>   #define BCM6328_LED_SHIFT(X)		((X) << 1)
>
>   /**
> @@ -126,9 +126,9 @@ static void bcm6328_led_set(struct led_classdev *led_cdev,
>   	*(led->blink_leds) &= ~BIT(led->pin);
>   	if ((led->active_low && value == LED_OFF) ||
>   	    (!led->active_low && value != LED_OFF))
> -		bcm6328_led_mode(led, BCM6328_LED_MODE_OFF);
> -	else
>   		bcm6328_led_mode(led, BCM6328_LED_MODE_ON);
> +	else
> +		bcm6328_led_mode(led, BCM6328_LED_MODE_OFF);
>   	spin_unlock_irqrestore(led->lock, flags);
>   }
>
> @@ -303,8 +303,8 @@ static int bcm6328_led(struct device *dev, struct device_node *nc, u32 reg,
>   			val = bcm6328_led_read(mode) >>
>   			      BCM6328_LED_SHIFT(shift % 16);
>   			val &= BCM6328_LED_MODE_MASK;
> -			if ((led->active_low && val == BCM6328_LED_MODE_ON) ||
> -			    (!led->active_low && val == BCM6328_LED_MODE_OFF))
> +			if ((led->active_low && val == BCM6328_LED_MODE_OFF) ||
> +			    (!led->active_low && val == BCM6328_LED_MODE_ON))
>   				led->cdev.brightness = LED_FULL;
>   			else
>   				led->cdev.brightness = LED_OFF;
>

Applied, thanks.

-- 
Best Regards,
Jacek Anaszewski
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Back to linux.kernel | Previous | Next | Find similar | Unroll thread

Thread

Re: [PATCH 2/2] leds-bcm6328: Swap LED ON and OFF definitions Jacek Anaszewski <j.anaszewski@samsung.com> - 2015-11-23 11:30 +0100

csiph-web