Groups | Search | Server Info | Keyboard shortcuts | Login | Register [http] [https] [nntp] [nntps]

Groups > linux.debian.user > #202183 > unrolled thread

Raid 0

Back to article view | Back to linux.debian.user

This discussion starts older than the indexed window; earlier articles aren't shown. The article labeled Started by below is the oldest one visible, not the original post.

Contents

  Raid 0 Finariu Florin <finariuf@yahoo.com> - 2018-11-06 15:00 +0100
    Re: Raid 0 gosho@oles.biz - 2018-11-06 15:10 +0100
    Re: Raid 0 Roberto C. Sánchez <roberto@debian.org> - 2018-11-06 15:10 +0100
    Re: Raid 0 Eduardo M KALINOWSKI <eduardo@kalinowski.com.br> - 2018-11-06 15:30 +0100
      Re: Raid 0 Dan Ritter <dsr@randomstring.org> - 2018-11-06 16:40 +0100

#202183 — Raid 0

[Multipart message — attachments visible in raw view] — view raw

 Hi,
Somebody can help me with some information about why I can not see the Raid0 created in bios?
I have a motherboard EPC602D8A with 2 chipsets: Intel C602 (Sata 2 x 4, Sata 3 x 2) and Marvell SE9172 (Sata 3 x 2). I create in BIOS a Raid0 on Marvel and another Raid0 on Intel C602.
When I start installation of OS in the section 'detect disk' it's show me nothing ask me to verify if the SSDs are connected. When I install OS with no Raid partition it see all SSDs I have plugged. I verified all SSDs one by one all cables too but nothing...
So how can I see the Raids created in Bios? Is something else should I do to be able to see them? I tried on RedHat, Fedora, CentOS, Kubuntu but the same thing!
So if you have informations about this please help me !
Thank you! 

[toc] | [next] | [standalone]

#202184

На 2018-11-06 15:49, Finariu Florin написа:
> Hi,
> Somebody can help me with some information about why I can not see the
> Raid0 created in bios?
> I have a motherboard EPC602D8A with 2 chipsets: Intel C602 (Sata 2 x
> 4, Sata 3 x 2) and Marvell SE9172 (Sata 3 x 2). I create in BIOS a
> Raid0 on Marvel and another Raid0 on Intel C602.
> When I start installation of OS in the section 'detect disk' it's show
> me nothing ask me to verify if the SSDs are connected. When I install
> OS with no Raid partition it see all SSDs I have plugged. I verified
> all SSDs one by one all cables too but nothing...
> So how can I see the Raids created in Bios? Is something else should I
> do to be able to see them? I tried on RedHat, Fedora, CentOS, Kubuntu
> but the same thing!
> So if you have informations about this please help me !
> Thank you!

Hi,

Your raid controller is not probably supported. A possible workarraound 
could be you to use LVM.

Kind regards
Georgi

[toc] | [prev] | [next] | [standalone]

#202187

On Tue, Nov 06, 2018 at 01:49:32PM +0000, Finariu Florin wrote:
>     Hi,
>    Somebody can help me with some information about why I can not see the
>    Raid0 created in bios?
>    I have a motherboard EPC602D8A with 2 chipsets: Intel C602 (Sata 2 x 4,
>    Sata 3 x 2) and Marvell SE9172 (Sata 3 x 2). I create in BIOS a Raid0 on
>    Marvel and another Raid0 on Intel C602.
>    When I start installation of OS in the section 'detect disk' it's show me
>    nothing ask me to verify if the SSDs are connected. When I install OS with
>    no Raid partition it see all SSDs I have plugged. I verified all SSDs one
>    by one all cables too but nothing...
>    So how can I see the Raids created in Bios? Is something else should I do
>    to be able to see them? I tried on RedHat, Fedora, CentOS, Kubuntu but the
>    same thing!
>    So if you have informations about this please help me !
>    Thank you! 

You probably need a special driver.  BIOS RAID is not real RAID; it
falls under the category of "fake RAID."

https://en.wikipedia.org/wiki/RAID#FAKE

Essentially, a BIOS RAID is really a crappy software RAID implementation
hosted on a chip.  It is the worst of everything.

If you need true RAID, then get a real RAID card (and be prepared to pay
a decent amount).  If you do not need real RAID, then setup your RAID as
a pure software RAID managed from within Linux.

If you use the BIOS fake RAID and your motherboard fails, there is a
good possibility that you will not be able to to recover the data from
your disks without another identical or nearly identical motherboard to
which you can connect the drives.  Linux software RAID, on the other
hand, lets you plug the disks into any machine running Linux and assemle
the array.

Regards,

-Roberto

-- 
Roberto C. Sánchez

[toc] | [prev] | [next] | [standalone]

#202189

On ter, 06 nov 2018, Finariu Florin wrote:
>  Hi,
> Somebody can help me with some information about why I can not see  
> the Raid0 created in bios?
> I have a motherboard EPC602D8A with 2 chipsets: Intel C602 (Sata 2 x  
> 4, Sata 3 x 2) and Marvell SE9172 (Sata 3 x 2). I create in BIOS a  
> Raid0 on Marvel and another Raid0 on Intel C602.
> When I start installation of OS in the section 'detect disk' it's  
> show me nothing ask me to verify if the SSDs are connected. When I  
> install OS with no Raid partition it see all SSDs I have plugged. I  
> verified all SSDs one by one all cables too but nothing...
> So how can I see the Raids created in Bios? Is something else should  
> I do to be able to see them? I tried on RedHat, Fedora, CentOS,  
> Kubuntu but the same thing!

It's the third time you've asked this. I'm assuming you're not  
subscribed to the list. You'd better subscribe in order to view the  
replies: https://lists.debian.org/debian-user/

Or at least look for replies in the web archives at that same address.  
But please don't keep reposting the same question.
-- 
Eduardo M KALINOWSKI
eduardo@kalinowski.com.br

[toc] | [prev] | [next] | [standalone]

#202198

Eduardo M KALINOWSKI: 
> On ter, 06 nov 2018, Finariu Florin wrote:
> >  Hi,
> > Somebody can help me with some information about why I can not see the
> > Raid0 created in bios?
> > I have a motherboard EPC602D8A with 2 chipsets: Intel C602 (Sata 2 x 4,
> > Sata 3 x 2) and Marvell SE9172 (Sata 3 x 2). I create in BIOS a Raid0 on
> > Marvel and another Raid0 on Intel C602.
> > When I start installation of OS in the section 'detect disk' it's show
> > me nothing ask me to verify if the SSDs are connected. When I install OS
> > with no Raid partition it see all SSDs I have plugged. I verified all
> > SSDs one by one all cables too but nothing...
> > So how can I see the Raids created in Bios? Is something else should I
> > do to be able to see them? I tried on RedHat, Fedora, CentOS, Kubuntu
> > but the same thing!
> 
> It's the third time you've asked this. I'm assuming you're not subscribed to
> the list. You'd better subscribe in order to view the replies:
> https://lists.debian.org/debian-user/
> 
> Or at least look for replies in the web archives at that same address. But
> please don't keep reposting the same question.

He got good, similar answers each time, and also thanked me in
private email.

So I don't know what's up, but it's safe to ignore further
repeats.

-dsr-

[toc] | [prev] | [standalone]

Back to top | Article view | linux.debian.user

csiph-web