Re: CD-RW failure to initialize

From	"ivan" <ivanjt@free.fr>
Message-ID	<sUWI7rB18pBd-pn2-BCwwdvvdkXz2@localhost> (permalink)
Newsgroups	comp.os.os2.setup.misc
Subject	Re: CD-RW failure to initialize
References	<Tze205IW65d5-pn2-SVdXghgoSdTs@81-174-221-213.pth-as14.dial.plus.net>
Date	2011-07-09 14:35 +0000
Organization	Guest of ProXad - France

Show all headers | View raw

Why not just zip uo the boot partition (zip -9rS) and then copy it to 
a USB stick?

ivan

On Sat, 9 Jul 2011 12:52:18 UTC, "yorkie" <kevh@yorkie.dabsolLL.co.uk>
wrote:

> Hi All,
> 
> 
> Bear with the longish post but I've tried to include as much
> as possible.
> 
> 
> I'm attempting to backup the system (Warp 4, FP13) to 
> upgrade to v4.51.
> 
> Plan A is thwarted by the fact that the system will not 
> operate the 
> CD-Writer correctly.  The system is as follows:-
> 
> 	SCSI HA 1 - Adaptec AHA-2944UW - BIOS enabled
> 	SCSI HA 2 - Advansys ABP-20 - Narrow, BIOS not enabled
> 	SCSI HDD x2 - on HA 1
> 	SCSI Teac 532s CD-R - on HA 2, LUN 3
> 	SCSI Ricoh MP7060S CD-RW - on HA 2, LUN 4
> 	Intel 10/100 NIC - unconfigured
> 	Aureal 2 sound card - unconfigured, no driver loaded
> 
> After Warp has booted-up the Writer has it's green LED on 
> all the 
> time when no CD is present (the CD-R does not).  This makes 
> me 
> believe that it is a hardware problem but I am unsure as it 
> might 
> be the default for a Ricoh drive (i.e. the light is 
> constant).  The 
> red LED always stays on all of time (when a CD is present), 
> never 
> less than five minutes, usually always on.  The properties 
> notebook 
> of the CD-R will appear on selection but not for the CD-RW 
> (SYS0039 The ?: device is not ready).
> 
> When the system was built the CD drives operated as they 
> should 
> but they were then on an Adaptec AHA-1522 card.  I had not 
> burnt 
> a CD for some months and it was only when I needed to 
> back-up 
> for the update that I noticed the problem. I've swapped the 
> Writer 
> for various others (all SCSI) but the issue persists and 
> I've also 
> swapped the Adaptec HA for the Advansys, again the result is
> the 
> same.  Cables ditto.  Maybe a motherboard problem?
> 
> The only thing that might have some bearing is when going 
> into 
> Selective Install the CD-Rom Device Support section shows an
> 
> entry of "Other".  I would have thought it should have been 
> something like "SCSI II".
> 
> 
> Config.sys (part of) is:-
> 
> 
> REM MODIFIED BY CONFIGSORT V2.1 ON 16/04/06 AT 11:35:13
> 
> REM *** INSTALLABLE FILE SYSTEMS ***
> IFS=G:\OS2\HPFS.IFS /CACHE:64 /LAZY:OFF /CRECL:4 
> /AUTOCHECK:GHIJ
> IFS=G:\OS2\BOOT\CDFS.IFS /Q /C:8 /M:32 /W
> REM IFS=G:\IBMLAN\NETPROG\NETWKSTA.200 /I:G:\IBMLAN /N
> 
> REM *** BASE DEVICE DRIVERS ***
> BASEDEV=IBMKBD.SYS
> BASEDEV=TIMER0.SYS
> BASEDEV=PRINT01.SYS
> BASEDEV=CHKDSK.SYS
> BASEDEV=IBM1FLPY.ADD
> REM BASEDEV=IBM2FLPY.ADD
> BASEDEV=XDFLOPPY.FLT
> BASEDEV=AIC7870.ADD
> REM BASEDEV=AHA152X.ADD /V
> BASEDEV=ASC.ADD /V /A:0 /!DM:3 !SM:3 /!DM:4 /!SM:4 /I-
> BASEDEV=OS2DASD.DMD  
> BASEDEV=OS2ASPI.DMD /ALL /SHARE (tried all the combinations
> BASEDEV=OS2SCSI.DMD /SHARE        - except the one that 
> works)
> 
> 
> 
> REM *** DEVICE DRIVERS ***
> DEVICE=G:\OS2\BOOT\TESTCFG.SYS
> DEVICE=G:\OS2\BOOT\DOS.SYS
> DEVICE=G:\OS2\BOOT\PMDD.SYS
> rem DEVICE=G:\OS2\BOOT\OS2CDROM.DMD /V
> DEVICE=G:\OS2\BOOT\JJSCDROM.DMD /VP  (tried this in 
> desperation)
> DEVICE=G:\OS2\BOOT\POINTDD.SYS
> DEVICE=G:\OS2\BOOT\MOUSE.SYS
> DEVICE=G:\OS2\BOOT\COM.SYS
> DEVICE=G:\OS2\BOOT\ASPIROUT.SYS /V
> DEVICE=G:\OS2\MDOS\VEMM.SYS
> DEVICE=G:\OS2\MDOS\VXMS.SYS /UMB
> DEVICE=G:\OS2\MDOS\VDPMI.SYS
> DEVICE=G:\OS2\MDOS\VDPX.SYS
> DEVICE=G:\OS2\MDOS\VCDROM.SYS
> DEVICE=G:\OS2\MDOS\VMOUSE.SYS
> DEVICE=G:\OS2\MDOS\VCOM.SYS
> DEVICE=G:\OS2\MDOS\VMGAX64.SYS
> DEVICE=G:\OS2\MDOS\VVGA.SYS
> DEVICE=G:\MGA\OS2\KMGAX64.SYS
> DEVICE=G:\MMOS2\SSMDD.SYS
> DEVICE=G:\MMOS2\R0STUB.SYS
> DEVICE=G:\MMOS2\MIDI.SYS
> DEVICE=G:\MMOS2\VCSHDD.SYS
> DEVICE=G:\MPTN\PROTOCOL\SOCKETS.SYS
> DEVICE=G:\MPTN\PROTOCOL\AFOS2.SYS
> DEVICE=G:\MPTN\PROTOCOL\AFINET.SYS
> DEVICE=G:\MPTN\BIN\VDOSTCP.VDD
> RUN=G:\MPTN\BIN\CNTRL.EXE
> RUN=G:\MPTN\BIN\VDOSCTL.EXE
> DEVICE=G:\IBMLAN\NETPROG\RDRHELP.200
> DEVICE=G:\IBMLAN\NETPROG\VNETAPI.OS2
> DEVICE=H:\FaxWorks\Fmd.sys L
> 
> 
> Here is how the BIOS boot initialisatiom looks:-
> 
> 	Onboard USB Controller = IRQ 15
> 		Slot 2 - SCSI   = IRQ 5
> 		Slot 3 - Multimedia Device = IRQ 9
> 		AGP VGA       = IRQ 9 
> 		Slot 4 - Ethernet = IRQ 10
> 		Slot 5 - SCSI   = IRQ 10
> 
> 
> The system reckons:-
> 
> RMVIEW: Physical view
>   IRQ Level =  0  PCI Pin = NONE  Flg = EXCLUSIVE    
> TIMER_CH_0 
>   IRQ Level =  1  PCI Pin = NONE  Flg = EXCLUSIVE    KBD_0 
> Keyboard Controller
>   IRQ Level =  2  PCI Pin = NONE  Flg = EXCLUSIVE    PIC_1 
>   IRQ Level =  3  PCI Pin = NONE  Flg = MULTIPLEXED  
> SERIAL_1 Serial Controller
>   IRQ Level =  4  PCI Pin = NONE  Flg = MULTIPLEXED  
> SERIAL_0 Serial Controller
>   IRQ Level =  5  PCI Pin = NONE  Flg = SHARED       
> AIC7870_0  Adaptec AIC7870
>   IRQ Level =  6  PCI Pin = NONE  Flg = MULTIPLEXED  
> FLOPPY_0 Floppy Controller
>   IRQ Level =  8  PCI Pin = NONE  Flg = EXCLUSIVE    RTC 
>   IRQ Level = 12  PCI Pin = NONE  Flg = EXCLUSIVE    AUX_0 
> PS/2 Auxiliary Device Controller
> 
> Hmmm.... IRQ 9 not listed, though I've no driver installed 
> nor has sound been configured.
> 	   IRQ 10 not listed - this should be the secondary SCSI HA
> (BIOS not enabled).
> 	   Also the NIC but that also is not configured until I'm 
> on cable.
> 	   
> 
> RMVIEW: Logical view
> 
> Logical Device: LDEV Logical Device Tree
> Flg:  0000   Class: ROOT      Handle: 00000000 
> 
>   Logical Device: DASD
>   Flg:  0000   Class: DASD      Handle: 00000000 
> 
>     Logical Device: DSKT_0  Diskette Drive 
>     Flg:  0000   Class: DASD      Handle: 0XFC5F08E0 
> 
>       System Name = A:  Logical DASD Volume
>       System Flags = 0000
> 
>       System Name = B:  Logical DASD Volume
>       System Flags = 0000
> 
>   Logical Device: CDROM
>   Flg:  0000   Class: CDROM     Handle: 00000000 
> 
>     Logical Device: CDROM_0  CD-ROM / CD-RW / DVDs Drive
>     Flg:  0000   Class: CDROM     Handle: 00000000 
> 
>       System Name = M:  Logical CD-ROM Volume
>       System Flags = 0000
> 
>     Logical Device: CDROM_1  CD-ROM / CD-RW / DVDs Drive
>     Flg:  0000   Class: CDROM     Handle: 00000000 
> 
>       System Name = N:  Logical CD-ROM Volume
>       System Flags = 0000
> 
> SERIAL, PARALLEL and TAPE snipped for brevity.
> 
> 
> 
> RMVIEW: Driver view
> 
> Driver: RESOURCE.SYS  -  IBM Resource Manager 
> Vendor: IBM OS/2  Version: 1.1  Date (MDY): 9/17/1994 
> Flag:   STATIC     Type-Subtype: SERVICE 
> 
> 
> Driver: IBMKBD.SYS  -  IBM Keyboard Device Dependent Driver 
> Vendor: IBM - OS/2  Version: 1.1  Date (MDY): 8/7/1998 
> Flag:   STATIC     Type-Subtype: OS2 - CHAR 
> 
>   Adapter: KBD_0 Keyboard Controller 
>   Device Type: INPUT-KBD      Bus/Width: PLANAR 8 BIT
>   I/O = 0X0060  Len =   1  Flg = SHARED      Addr Lines = 16
> 
>   I/O = 0X0064  Len =   1  Flg = SHARED      Addr Lines = 16
> 
>   IRQ Level =  1  PCI Pin = NONE  Flg = EXCLUSIVE    
> 
>   Device: KBD_X Unknown Keyboard Device      IO           
> 
> Hmmmm.... I'll have to look into the keyoard setup
> 
> Driver: IBM1FLPY.ADD  -  IBM Family 1 Floppy Driver 
> Vendor: IBM OS/2  Version: 1.1  Date (MDY): 9/17/1994 
> Flag:   STATIC     Type-Subtype: ADDDM - ADD 
> 
>   Adapter: FLOPPY_0 Floppy Controller 
>   Device Type: MS-FLPY        Bus/Width: ISA 8 BIT
>   IRQ Level =  6  PCI Pin = NONE  Flg = MULTIPLEXED  
>   I/O = 0X03F0  Len =   6  Flg = MULTIPLEXED Addr Lines = 16
> 
>   I/O = 0X03F7  Len =   1  Flg = MULTIPLEXED Addr Lines = 16
> 
>   DMA Channel =  2  Flg =  MULTIPLEXED 
> 
>   Device: DSKT_0 1.44MB Diskette Drive   REMOVABLE  DISK    
>     
> 
> Driver: AIC7870.ADD  -  Adaptec AIC7870 SCSI Adapter Driver 
> Vendor: IBM - OS/2  Version: 1.1  Date (MDY): 9/6/1994 
> Flag:   STATIC     Type-Subtype: ADDDM - ADD 
> 
>   Adapter: AIC7870_0  Adaptec AIC7870 
>   Device Type: MS-SCSI        Bus/Width: PCI 32 BIT
>   I/O = 0XDC00  Len =  16  Flg = EXCLUSIVE   Addr Lines = 16
> 
>   IRQ Level =  5  PCI Pin = NONE  Flg = SHARED       
> 
>   Device: DISK_(8,0)  IBM OEM  DFHSS4E          5454      
> DISK         
> 
>   Device: DISK_(9,0)  IBM OEM  DFHSS4E          4343      
> DISK         
> 
> 
> Driver: OS2DASD.DMD  -  OS2DASD OS/2 DASD Device Manager 
> Vendor: IBM  Version: 1.1  Date (MDY): 9/13/1994 
> Flag:   STATIC     Type-Subtype: ADDDM - DM 
> 
>   Logical Device: DSKT_0  Diskette Drive 
>   Flg:  0000   Class: DASD      Handle: 0XFC5F08E0 
> 
>   System Name = A:  Logical DASD Volume
>   System Flags = 0000
> 
>   System Name = B:  Logical DASD Volume
>   System Flags = 0000
> 
> Driver: OS2ASPI.DMD  -  Non-Resource manager aware base 
> device driver 
> Vendor: Unknown Vendor  Version: 1.1  Date (MDY): 9/17/1994 
> Flag:   STATIC     Type-Subtype: OS2 -   
> 
> Driver: OS2SCSI.DMD  -  Non-Resource manager aware base 
> device driver 
> Vendor: Unknown Vendor  Version: 1.1  Date (MDY): 9/17/1994 
> Flag:   STATIC     Type-Subtype: OS2 -   
> 
> 
> 
> Driver: JJSCDROM.DMD  -  Modified CD-ROM / CD-RW / DVDs 
> Device Manager 
> Vendor: Takayuki 'January June' Suwa  Version: 1.1  Date 
> (MDY): 3/28/2003 
> Flag:   STATIC     Type-Subtype: ADDDM - DM 
> 
>   Logical Device: CDROM_0  CD-ROM / CD-RW / DVDs Drive
>   Flg:  0000   Class: CDROM     Handle: 00000000 
> 
>   System Name = M:  Logical CD-ROM Volume
>   System Flags = 0000
> 
>   Logical Device: CDROM_1  CD-ROM / CD-RW / DVDs Drive
>   Flg:  0000   Class: CDROM     Handle: 00000000 
> 
>   System Name = N:  Logical CD-ROM Volume
>   System Flags = 0000
> 
> 
> 
> Driver: ASPIROUT.SYS  -  ASPI Router Device Driver (V1.1á10)
> 
> Vendor: Paul Ratcliffe  Version: 1.1  Date (MDY): 10/9/2005 
> Flag:   STATIC     Type-Subtype: OS2 - HELPER 
> 
> 
> Deleted many in the listing which did not appear to have a 
> bearing on the issue.
> Resource.sys, I notice, is dated 17th September 1994 - I 
> would have thought
> that newer stuff would need a more up-to-date aware 
> sniffer/manager.
> 
> 
> Any thoughts?
> 
> 


--

Back to comp.os.os2.setup.misc | Previous | Next — Previous in thread | Next in thread | Find similar

Thread

CD-RW failure to initialize "yorkie" <kevh@yorkie.dabsolLL.co.uk> - 2011-07-09 07:52 -0500
  Re: CD-RW failure to initialize "ivan" <ivanjt@free.fr> - 2011-07-09 14:35 +0000
    Re: CD-RW failure to initialize "yorkie" <kevh@yorkie.dabsolLL.co.uk> - 2011-07-16 04:46 -0500
      Re: CD-RW failure to initialize "ivan" <ivanjt@free.fr> - 2011-07-17 08:35 +0000
        Re: CD-RW failure to initialize "yorkie" <kevh@yorkie.dabsolLL.co.uk> - 2011-07-17 10:01 -0500
          Re: CD-RW failure to initialize "ivan" <ivanjt@free.fr> - 2011-07-17 19:00 +0000
            Re: CD-RW failure to initialize "yorkie" <kevh@yorkie.dabsolLL.co.uk> - 2011-07-30 15:19 -0500
              Re: CD-RW failure to initialize "ivan" <ivanjt@free.fr> - 2011-07-31 09:40 +0000
              Re: CD-RW failure to initialize "Doug Bissett" <dougb007!SPAM@telus.net> - 2011-07-31 14:56 +0000
                Re: CD-RW failure to initialize "ivan" <ivanjt@free.fr> - 2011-08-01 09:22 +0000
                Re: CD-RW failure to initialize "Doug Bissett" <dougb007!SPAM@telus.net> - 2011-08-01 19:40 +0000
                Re: CD-RW failure to initialize "Doug Bissett" <dougb007!SPAM@telus.net> - 2011-08-02 15:14 +0000
                Re: CD-RW failure to initialize Dave Yeo <dave.r.yeo@gmail.com> - 2011-08-02 20:10 -0700
  Re: CD-RW failure to initialize johnsuth@nospam.com.au - 2011-07-10 01:14 +0000
    Re: CD-RW failure to initialize "yorkie" <kevh@yorkie.dabsolLL.co.uk> - 2011-07-16 04:46 -0500

csiph-web